Envoy, Rainer, Trailblazer 2006-2007

6.0L V8 VIN H Auto 6

Print

Trouble Code: P2135



Throttle Position (TP) Sensor 1-2 Correlation

Trouble Code: P2138



Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Trouble Code: P2176



Minimum Throttle Position Not Learned

Trouble Code: P2534



Ignition 1 Switch Circuit Low Voltage

Possible Causes:



If all circuit tests are OK, ensure the transmission pass through connector and harness terminals are clean and not damaged, and the charging system is functioning correctly.
 
Verify there is a good connection at the body control module (BCM) especially if DTC P0700 is also set with this code.
 

Trouble Code: P2544



Transmission Torque Request Circuit

Possible Causes:



This diagnostic trouble code may set due to low system voltage. Ensure that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test . Verify charging system is operating correctly. Refer to Charging System Test . Verify there is no parasitic drain on the battery. Refer to Battery Electrical Drain/Parasitic Load Test .
 

Trouble Code: P2763



Torque Converter Clutch (TCC) Pressure Control (PC) Solenoid Control Circuit High Voltage

Trouble Code: P2764



Torque Converter Clutch (TCC) Pressure Control (PC) Solenoid Control Circuit Low Voltage

Trouble Code: P2769



Torque Converter Clutch (TCC) Enable Solenoid Control Circuit Low Voltage

Possible Causes:



With the TCC engaged, the TCC slip speed should be -20 to +40 RPM.
 

Trouble Code: P2770



Torque Converter Clutch (TCC) Enable Solenoid Control Circuit High Voltage

Trouble Code: P2771



Four Wheel Drive (4WD) Low Switch Circuit

Possible Causes:



Verify that the input speed sensor (ISS) and the output speed sensor (OSS) are functioning properly.
 
In 3rd gear at approximately 64 km/h (40 mph), command TCC ON. If functioning properly the OSS will track ISS and the engine RPM.
 
If not, refer to DTC P0716 for the ISS and DTC P0723 for the OSS.
 

Trouble Code: P2A00



HO2S 1 Sensor Circuit

Trouble Code: P2A01



HO2S Performance Bank 1 Sensor 2

Trouble Code: P2A03



HO2S 22 (Bank 2 Sensor 2) Performance

Trouble Code: P2A04



HO2S Performance Bank 2 Sensor 2

Trouble Code: U0001



High Speed CAN Communication Bus

Possible Causes:



This DTC cannot be retrieved with a current status. Diagnosis of current DTC is accomplished via the symptom, Scan Tool Does Not Communicate with GMLAN Device. Refer to Scan Tool Does Not Communicate with High Speed GMLAN Device .
 
An intermittent condition is likely to be caused by a short on the GMLAN serial data circuits. Use the Scan Tool Does Not Communicate with GMLAN Device procedure in order to isolate an intermittent condition. Refer to Scan Tool Does Not Communicate with High Speed GMLAN Device .
 

Trouble Code: U0073



Controller Area Network (CAN) Bus Communication

Possible Causes:



This DTC cannot be retrieved with a current status. Diagnosis of a current DTC is accomplished via the symptom, Scan Tool Does Not Communicate with High and/or Low Speed GMLAN Device. Refer to Data Link References for the correct procedure for the specific module(s) and the busses they use to communicate.
 
An intermittent condition is likely to be caused by a short on the GMLAN serial data circuits. Use the Scan Tool Does Not Communicate with High and/or Low Speed GMLAN Device procedure in order to isolate an intermittent condition. Refer to Data Link References for the correct procedure for the specific modules.
 

Trouble Code: U0100



Lost Communication With Engine/Powertrain Control Module (ECM/PCM)

Possible Causes:



A poor connection at the inoperative module may cause this code to set.
 
An improperly powered module may cause this code to set.
 

Trouble Code: U0101



Lost Communication With Transmission Control Module (TCM)

Possible Causes:



A poor connection at the inoperative module may cause this code to set.
 
An improperly powered module may cause this code to set.
 

Trouble Code: U0299



N/A

Possible Causes:



A poor connection at the inoperative module may cause this code to set.
 
An improperly powered module may cause this code to set.
 

Trouble Code: U1000



Class 2 Data Link Malfunction

Possible Causes:



When a malfunction occurs while modules are communicating, a lost communication DTC is set as a current DTC. When the modules stop communicating the current lost communication DTC is cleared but the history DTC remains. When the modules begin to communicate again, the module with the open fuse will not be learned by the other modules so U1000 is set current by the other modules. If the malfunction occurs when the modules are not communicating, only U1000 is set.
 

Trouble Code: U1001



Lost Communication with XXX

Possible Causes:



An intermittent open between a module and a star connector may cause this DTC to set.
 
A poor connection at a module or a star connector may cause this DTC to set.
 
An intermittent open in a star connector may cause this DTC to set.
 
An open voltage or ground circuit to a module may cause this DTC to set.
 
An internal module malfunction may cause this DTC to set.
 

Trouble Code: U1241



Lost Communication With Scan Tool

Possible Causes:



DTC U1241 does not indicate a system malfunction and will not cause any warning indicators to illuminate. When DTC U1241 sets, cycle the ignition and use the scan tool to clear the code, no further diagnosis is necessary.
 

Trouble Code: U1254



Lost Communication with XXX

Possible Causes:



An intermittent open between a module and a star connector may cause this DTC to set.
 
A poor connection at a module or a star connector may cause this DTC to set.
 
An intermittent open in a star connector may cause this DTC to set.
 
An open voltage or ground circuit to a module may cause this DTC to set.
 
An internal module malfunction may cause this DTC to set.
 

Trouble Code: U2100



High Speed CAN Communication Bus

Possible Causes:



This DTC cannot be retrieved with a current status. Diagnosis of current DTC is accomplished via the symptom, Scan Tool Does Not Communicate with high speed GMLAN Device. Refer to Scan Tool Does Not Communicate with High Speed GMLAN Device .
 
An intermittent condition is likely to be caused by a short on the high speed high speed GMLAN serial data circuits. Use the Scan Tool Does Not Communicate with high speed GMLAN Device procedure in order to isolate an intermittent condition. Refer to Scan Tool Does Not Communicate with High Speed GMLAN Device .
 

Trouble Code: U2105



Lost Communication With Engine Control Module (ECM)

Possible Causes:



A poor connection at the inoperative module may cause this code to set.
 
An improperly powered module may cause this code to set.
 

Trouble Code: U2199



Unassigned

Possible Causes:



A poor connection at the inoperative module may cause this code to set.
 
An improperly powered module may cause this code to set.
 

 
label.common.footer.alt.autozoneLogo