Escalade, Suburban 1500 & 2500, Tahoe, Yukon, Yukon XL 1500 & 2500 (2006-2007), Yukon Denali and Yukon Denali XL (2005-2006)

5.3L V8 VIN J Auto 11

Print

Trouble Code: P2125



Accelerator Pedal Position (APP) Sensor 2 Circuit

Possible Causes:



Inspect the throttle actuator control (TAC) module connectors for signs of water intrusion. If water intrusion occurs, multiple DTCs may set without any circuit or component conditions found during diagnostic testing.
 
When the TAC module detects a condition within the TAC system, more than one TAC system related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Disconnecting components during testing may set additional DTCs. Remember this if you review the stored information in Capture Info.
 
For an intermittent, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P2135



Throttle Position (TP) Sensor 1-2 Correlation

Possible Causes:



Inspect the TAC module connectors for signs of water intrusion. If water intrusion occurs, multiple DTCs may set without any circuit or component conditions found during diagnostic testing.
 
When the TAC module detects a condition within the TAC system, more than one TAC system related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Disconnecting components during testing may set additional DTCs. Remember this if you review the stored information in Capture Info.
 
If this DTC is determined to be intermittent, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P2138



Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Possible Causes:



The PCM compares the signal of each of the accelerator pedal position sensor to each other throughout the entire range of operation. Clear the DTCs and actuate the pedal through the entire range with the ignition ON and the engine OFF.
 
Use the J 35616 Connector Test Adapter Kit for any test that requires probing the PCM harness connector or a component harness connector. Using this kit will prevent damage to the harness connector terminals.
 
For intermittent conditions, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P2534



Ignition 1 Switch Circuit Low Voltage

Possible Causes:



If all circuit tests are OK, ensure the transmission pass through connector and harness terminals are clean and not damaged, and the charging system is functioning correctly.
 
Verify there is a good connection at the body control module (BCM) especially if DTC P0700 is also set with this code.
 

Trouble Code: P2610



Control Module Ignition Off Timer Performance

Trouble Code: P2636



Fuel Transfer Pump Flow Insufficient

Trouble Code: P2670



Actuator Supply Voltage 2 Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2671



Actuator Supply Voltage 2 High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2714



Clutch Pressure Control (PC) Solenoid 4 - Stuck Off

Possible Causes:



When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure conditions.
 

Trouble Code: P2715



Clutch Pressure Control (PC) Solenoid 4 - Stuck On

Possible Causes:



When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure conditions.
 

Trouble Code: P2719



Clutch Pressure Control (PC) Solenoid 4 System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2720



Clutch Pressure Control (PC) Solenoid 4 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2721



Clutch Pressure Control (PC) Solenoid 4 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2723



Clutch Pressure Control (PC) Solenoid 5 - Stuck Off

Possible Causes:



When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure conditions.
 

Trouble Code: P2723



Pressure Control Solenoid 1 (PCS1) Controlled Clutch Stuck Off

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC indicates the on-coming clutch being controlled by PCS1 is not applied or applied too slowly. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, in order to determine the specific shift when the DTC was set. Refer to the Solenoid and Clutch Chart to determine which clutch circuit is suspect.Important: Clutch failure due to installation of an engine power upgrade is not covered under the manufacturers warranty. Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur.
 

Trouble Code: P2724



Clutch Pressure Control (PC) Solenoid 5 - Stuck On

Possible Causes:



When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure conditions.
 

Trouble Code: P2724



Pressure Control Solenoid 1 (PCS1) Controlled Clutch Stuck On

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.This DTC indicates the off-going clutch being controlled by PCS1 is not releasing or is slow to release. This could indicate a leak or obstruction in a specific clutch apply circuit. Observe scan tool failure record data for previous or current range information when the DTC was set, in order to determine the specific shift when the DTC was set. Refer to the Solenoid and Clutch Chart to determine which clutch circuit is suspect.Important: Clutch failure due to installation of an engine power upgrade is not covered under the manufacturers warranty. Inspect for the presence of an add-on engine power package. When engine horsepower or torque is increased over factory rating, a shift flare condition may occur.
 

Trouble Code: P2727



Pressure Control Solenoid 1 (PCS1) Control Circuit Open (A)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2728



Clutch Pressure Control (PC) Solenoid 5 System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2729



Clutch Pressure Control (PC) Solenoid 5 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2729



Pressure Control Solenoid 1 (PCS1) Control Circuit Low (A)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2730



Clutch Pressure Control (PC) Solenoid 5 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2730



Pressure Control Solenoid 1 (PCS1) Control Circuit High (A)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2761



Torque Converter Clutch (TCC) Pressure Control (PC) Solenoid Control Circuit

Possible Causes:



DTC P2761 defaults to an elevated line pressure condition which may result in partial TCC apply. This may produce an idle surge that could stall the engine.
 

Trouble Code: P2761



Torque Converter Clutch (TCC) Pressure Control (PC) Solenoid Control Circuit

Trouble Code: P2761



Torque Converter Clutch (TCC) Pressure Control Solenoid (PCS) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P2761 set in combination with DTC P0960 and P2727 may indicate an open in the HSD circuit.
 

Trouble Code: P2762



Torque Converter Clutch (TCC) Pressure Control Solenoid System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2763



Torque Converter Clutch (TCC) Pressure Control Solenoid Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2763



Torque Converter Clutch (TCC) Pressure Control Solenoid (PCS) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2764



Torque Converter Clutch (TCC) Pressure Control Solenoid Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P2764



Torque Converter Clutch (TCC) Pressure Control Solenoid (PCS) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P2771



Four Wheel Drive (4WD) Low Switch Circuit

Possible Causes:



Low pump pressure and a slipping transmission may cause DTC P2771 to set.
 
Transfer case ratio is calculated by dividing the ISS by the OSS.
 

Trouble Code: P2771



Four Wheel Drive (4WD) Low Switch Circuit

Possible Causes:



Verify that the input speed sensor (ISS) and the output speed sensor (OSS) are functioning properly.
 
In 3rd gear at approximately 64 km/h (40 mph), command TCC ON. If functioning properly the OSS will track ISS and the engine RPM.
 
If not, refer to DTC P0716 for the ISS and DTC P0723 for the OSS.
 

Trouble Code: P2771



4WD Low Switch Circuit

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.Inspect for any transmission DTCs that may have set again.
 

Trouble Code: P2796



Auxiliary Transmission Fluid Pump Relay Control Circuit

Possible Causes:



The Auxiliary Transmission Fluid Pump Relay can be controlled using a Scan Tool. This feature is located in the HCM Output Controls on the scan tool.
 
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P2797



Auxiliary Transmission Fluid Pump Performance

Possible Causes:



The Auxiliary Transmission Fluid Pump Relay can be controlled using a Scan Tool. This feature is located in the HPCM Output Controls on the scan tool.
 
Inspect for restricted Auxiliary Transmission Fluid Pump pickup filter.
 
Inspect for leaking at the Auxiliary Transmission Fluid Pump mounting surface.
 
Inspect charging system and battery voltage for correct operation.
 
Ensure all Engine Idle Off enabling criteria have been met to ensure auxiliary transmission fluid pump operation is possible.
 
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P2A01



HO2S Performance Bank 1 Sensor 2

Trouble Code: P2A04



HO2S Performance Bank 2 Sensor 2

Trouble Code: U0001



High Speed CAN Communication Bus

Possible Causes:



This DTC cannot be retrieved with a current status. Diagnosis of current DTC is accomplished via the symptom, Scan Tool Does Not Communicate with GMLAN Device. Refer to Scan Tool Does Not Communicate with High Speed GMLAN Device .
 
An intermittent condition is likely to be caused by a short on the GMLAN serial data circuits. Use the Scan Tool Does Not Communicate with GMLAN Device procedure in order to isolate an intermittent condition. Refer to Scan Tool Does Not Communicate with High Speed GMLAN Device .
 

Trouble Code: U0073



High Speed CAN Communication Bus

 
label.common.footer.alt.autozoneLogo