Escalade, Suburban 1500 & 2500, Tahoe, Yukon, Yukon XL 1500 & 2500 (2006-2007), Yukon Denali and Yukon Denali XL (2005-2006)

6.2L V8 VIN 8 Auto 7

Print

Trouble Code: P0894



Transmission Component Slipping

Possible Causes:



A TFP manual valve position switch malfunction can set DTC P0894.
 
A mechanical failure of the shift solenoids or TCC PWM solenoid valve can set DTC P0894.
 
Internal transmission failures can result in a DTC P0894.
 
Sticking or contaminated shift valves may cause intermittent slipping in D4.
 
DTC P0894 defaults to an elevated line pressure condition which may result in partial TCC apply. This may produce an idle surge that could stall the engine.
 

Trouble Code: P0894



Transmission Component Slipping

Possible Causes:



Bronze material found in the transmission oil pan may indicate stator shaft bushing wear. If bushing wear is suspected, inspect the stator shaft and the input, turbine, shaft for damage.
 
Refer to Symptoms - Automatic Transmission for more information.
 

Trouble Code: P0960



Pressure Control Solenoid (PCS) Main Modulation (MAIN MOD) Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0960, set in combination with DTC P2727 and P2761, may indicate an open in the high side driver circuit.
 

Trouble Code: P0961



Line Pressure Control (PC) Solenoid System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0962



Line Pressure Control (PC) Solenoid Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0962



Pressure Control Solenoid (PCS) Main Modulation (MAIN MOD) Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0963



Line Pressure Control (PC) Solenoid Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0963



Pressure Control Solenoid (PCS) Main Modulation (MAIN MOD) Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0964



Pressure Control Solenoid 2 (PCS2) Control Circuit Open (B)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0964 set in combination with DTC P0972, P0975 and P0978 may indicate an open in the HSD2 circuit.
 

Trouble Code: P0965



Clutch Pressure Control (PC) Solenoid 2 System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, it may be helpful to ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0966



Clutch Pressure Control (PC) Solenoid 2 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, it may be helpful to ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0966



Pressure Control Solenoid 2 (PCS2) Control Circuit Low (B)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0967



Clutch Pressure Control (PC) Solenoid 2 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, it may be helpful to ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0967



Pressure Control Solenoid 2 (PCS2) Control Circuit High (B)

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0969



Clutch Pressure Control (PC) Solenoid 3 System Performance

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0970



Clutch Pressure Control (PC) Solenoid 3 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0971



Clutch Pressure Control (PC) Solenoid 3 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0972



Shift Solenoid 1 (SS1) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0972, when set in combination with DTC P0964, P0975 and P0978, may indicate an open in the actuator supply voltage 2 circuit.
 

Trouble Code: P0973



Shift Solenoid (SS) 1 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the control solenoid (w/body and TCM) valve assembly is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0973



Shift Solenoid 1 (SS1) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0974



Shift Solenoid (SS) 1 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the control solenoid (w/body and TCM) valve assembly is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0974



Shift Solenoid 1 (SS1) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0975



Shift Solenoid 2 (SS2) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0975, when set in combination with DTC P0964, P0972 and P0978, may indicate an open in the actuator supply voltage 2 circuit
 

Trouble Code: P0976



Shift Solenoid (SS) 2 Control Circuit Low Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0976



Shift Solenoid 2 (SS2) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0977



Shift Solenoid (SS) 2 Control Circuit High Voltage

Possible Causes:



When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in 2nd gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
 

Trouble Code: P0977



Shift Solenoid 2 (SS2) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0978



Shift Solenoid 3 (SS3) Control Circuit Open

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.DTC P0978, when set in combination with DTC P0964, P0972 and P0975, may indicate an open in the actuator supply voltage 2 circuit.
 

Trouble Code: P0979



Shift Solenoid 3 (SS3) Control Circuit Low

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0980



Shift Solenoid 3 (SS3) Control Circuit High

Possible Causes:



Inspect the wiring for poor electrical connections at the TCM. Inspect for the following conditions:

A bent terminal
 
A backed-out terminal
 
A damaged terminal
 
Poor terminal tension
 
A chafed wire
 
A broken wire inside the insulation
 

When diagnosing for an intermittent short or open, massage the wiring harness while watching the test equipment for a change.You may have to drive the vehicle in order to experience a condition.
 

Trouble Code: P0989



Transmission Fluid Pressure (TFP) Switch 5 Circuit Low Voltage

Trouble Code: P0990



Transmission Fluid Pressure (TFP) Switch 5 Circuit High Voltage

Trouble Code: P1121



Throttle Position (TP) Sensor Circuit Intermittent High Voltage

Trouble Code: P1122



Throttle Position (TP) Sensor Circuit Intermittent Low Voltage

Trouble Code: P1125



Accelerator Pedal Position (APP) System

Trouble Code: P1133



HO2S Insufficient Switching Bank 1 Sensor 1

Trouble Code: P1134



HO2S Transition Time Ratio Bank 1 Sensor 1

Trouble Code: P1153



HO2S Insufficient Switching Bank 2 Sensor 1

Trouble Code: P1154



HO2S Transition Time Ratio Bank 2 Sensor 1

Trouble Code: P1380



Misfire Detected - Rough Road Data Not Available

 
label.common.footer.alt.autozoneLogo