Escalade, Suburban, Tahoe, Yukon, Denali, DenaliXL, YukonXL 1999-2005

Ignition Switch

Print

Removal & Installation




CAUTION
When performing service around the SIR system components or wiring, the SIR system MUST be disabled. Failure to do so could result in possible air bag deployment, personal injury or unneeded SIR system repairs.

  1. Disable the SIR system. Refer to the Chassis Electrical Section.
  2.  
  3. Make sure the switch is in the OFF position.
  4.  
  5. Remove the steering wheel as outlined in this section.
  6.  
  7. Disconnect the tilt wheel lever by pulling it out.
  8.  
  9. Remove the knee bolster and the Torx® head screws from the lower column cover.
  10.  
  11. Lower the cover by tilting it down and then sliding it back to disengage the locking tabs.
  12.  
  13. Remove the Torx® head screws from the upper column cover.
  14.  
  15. Remove the steering column lock set and the upper cover.
  16.  
  17. Disconnect the wiring harness straps from the steering column wiring harness.
  18.  
  19. Remove the retainer from Connector Position Assurance (CPA) if equipped.
  20.  
  21. Disengage the connector from the Brake Transmission Shift Interlock (BTSI) if equipped.
  22.  
  23. Unplug the gray and black connectors from the bulkhead connector.
  24.  
  25. Unfasten the Torx® head screws from the switch and remove the switch.

    Click image to see an enlarged view

    Fig. Exploded view of the multi-function switch-1999-02 models

  26.  

To install:

Installation is the reverse of removal but please note the following important steps.

  1. Install the switch. Use a small blade screwdriver to compress the electrical contact and move the switch into position. The electrical contact must rest on the canceling cam assembly.
  2.  
  3. Fasten the Torx® head screws on the switch. Tighten the screws to 53 inch. lbs. (6 Nm).
  4.  
  5. Install the upper column cover and fasten the column bracket nuts. Tighten the nuts to 22 ft. lbs. (30 Nm).
  6.  
  7. Install the knee bolster and the steering column cylinder lock. Tighten the column cover Torx® screws to 12 inch. lbs. (1.4 Nm).
  8.  
  9. Install the lower column cover and tighten the Torx® screws 53 inch. lbs. (6 Nm).
  10.  
  11. Make sure the switch is in the OFF position and install the steering wheel. Refer to this section for this procedure.
  12.  
  13. Enable the SIR system (if equipped).
  14.  


NOTE
The steering column must be removed from the vehicle to perform the following procedure.

  1. Disable the inflatable restraint steering wheel module. Refer to AIR BAG/SIR.
  2.  
  3. Remove the upper and lower trim covers.
    NOTE
    The abrasion sleeve located on the steering column wire harness assembly must be reinstalled. Make note of what connector (electronic lock module assembly) is coming out of the middle of the abrasion sleeve for installation purposes.

  4.  
  5. Remove the wire harness strap from the steering column and the wire harness assembly.
  6.  
  7. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
  8.  
  9. Rotate the key alarm connector 90 degrees.
  10.  
  11. Pull the key alarm connector out of the electronic lock module assembly.
  12.  
  13. Remove the passkey connector from the electronic lock module assembly.
  14.  
  15. Insert tool J42759 or equivalent into the electronic lock module assembly and slide the ignition and key alarm switch assembly out.

    Click image to see an enlarged view

    Fig. Using tool J42759 to release ignition switch from lock module assembly.

  16.  

To install:

  1. Insert tool J42759 into the electronic lock module assembly and slide the ignition and key alarm switch assembly into the lock module assembly.
  2.  
  3. Push the key alarm connector into the electronic lock module assembly.
  4.  
  5. Rotate the key alarm connector 90 degrees so that the key alarm connector locks into place.
  6.  
  7. Install the passkey connector into the electronic lock module assembly.
  8.  
  9. Slide the 2 connectors of the turn signal and multifunction switch assembly into the bulkhead connector.
    NOTE
    The abrasion sleeve must be installed back onto the steering column wire harness assembly. The electronic lock module assembly wires and connector must be hanging out of the middle of the abrasion sleeve.

  10.  
  11. Attach the wire harness strap to the wire harness assembly and the steering column.
  12.  
  13. Install the upper and lower trim covers.
  14.  
  15. Enable the inflatable restraint steering wheel module.
  16.  

  1. Disable the SIR system. Refer to AIR BAG/SIR.
  2.  
  3. Remove the knee bolster.
  4.  
  5. Remove the steering column trim covers from the steering column.
  6.  
  7. Disconnect the steering column electrical connectors.
  8.  
  9. Remove the wire harness assembly from the steering column and the wire harness strap.
  10.  
  11. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
  12.  
  13. Rotate the key alarm connector 90 degrees.
  14.  
  15. Pull the key alarm connector out of the lock module assembly.
  16.  
  17. Remove the passkey connector from the lock module assembly.
  18.  
  19. Remove the connector from the electric park lock (vehicles equipped with floor shifters).
  20.  

To install:

  1. Install the ignition switch to the lock module.
  2.  
  3. Install the key alarm connector into the lock module assembly.
  4.  
  5. Push the key alarm connector  into the lock module assembly.
  6.  
  7. Rotate the key alarm connector 90 degrees so that the key alarm connector locks into place.
  8.  
  9. Install the passkey connector into the lock module assembly.
  10.  
  11. Install the connector to the electric park lock (vehicles equipped with floor shifters).
  12.  
  13. Slide the 2 connectors of the turn signal and multifunction switch into the bulkhead connector.
  14.  
  15. Attach the wire harness assembly to the steering column wire harness strap.
  16.  
  17. Connect the steering column electrical connectors to the vehicle.
  18.  
  19. Install the trim covers to the column.
  20.  
  21. Install the knee bolster.
  22.  
  23. Enable the SIR system.
  24.  

  1. Disconnect the negative battery cable.
  2.  
  3. Disable the SIR system. Refer to AIR BAG/SIR.
  4.  
  5. Remove the hush and knee bolster.
  6.  
  7. Remove the steering column trim covers.
  8.  
  9. With the key installed, turn the key to the RUN position.
  10.  
  11. Install an Allen wrench into the hole on top of the lock cylinder housing. Push down on the Allen wrench to release the tab on the lock cylinder inside the lock cylinder housing.
  12.  
  13. Slide the lock cylinder out of the lock cylinder housing.
  14.  
  15. Disconnect the passlock and key buzzer from the lock cylinder housing.
  16.  
  17. Insert tool J42759 or equivalent into the lock cylinder housing to release the tabs on the ignition switch.
  18.  
  19. Pull the ignition switch out of the lock cylinder housing.
  20.  
  21. Disconnect the connector from the ignition switch.
  22.  

To install:


NOTE
: The gears between the ignition switch and the lock cylinder housing must be in the correct position. Failure to do so will cause a misalignment of the gears in the ignition switch and the lock cylinder housing, which may result in a NO START or BATTERY DRAIN.



Click image to see an enlarged view

Fig. Verify the alignment of the gear in the ignition switch. If gear is not in position shown, turn gear in ignition switch until you reach the correct position.


NOTE
In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock.

  1. Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop.
  2.  
  3. Connect the connector to the ignition switch.
  4.  
  5. Insert the ignition switch into the lock cylinder housing. The tabs on the ignition switch MUST be seated inside the lock cylinder housing for proper installation.

    Click image to see an enlarged view

    Fig. Tabs on ignition switch engage slots in lock cylinder housing.

  6.  
  7. Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position - allowing it to spring return into the RUN position.

    Click image to see an enlarged view

    Fig. Screwdriver does the trick on this job.

  8.  
  9. Align the lock cylinder and install the lock cylinder into the lock cylinder housing.
  10.  
  11. Connect the passlock and key buzzer into the lock housing.
  12.  
  13. Install the steering column trim covers.
  14.  
  15. Install the hush and knee bolster.
  16.  
  17. Enable the SIR system.
  18.  
  19. Connect the negative battery cable.
  20.  


CAUTION
If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System in AIR BAG/SIR.

  1. Disconnect the negative battery cable.
  2.  
  3. Disable the SIR system. Refer to the Chassis Electrical Section.
  4.  
  5. Remove the hush and knee bolster.
  6.  
  7. Remove the steering column trim covers.
  8.  
  9. With the key installed, turn the key to the RUN position on 2005-06 models. On 2007 models turn the key to the START position.
  10.  
  11. Insert an Allen wrench into the hole on top of the lock cylinder housing. Push down on the Allen wrench to release the tab on the lock cylinder inside the lock cylinder housing.

    Click image to see an enlarged view

    Fig. Insert Allen wrench through hole, push down on tab and slide out the lock cylinder

  12.  
  13. Slide the lock cylinder out of the lock cylinder housing.
  14.  
  15. Disconnect the passlock and key buzzer from the lock cylinder housing.
  16.  
  17. Insert J 42759 into the lock cylinder housing to release the tabs on the ignition switch.

    Click image to see an enlarged view

    Fig. Insert J 42759 into the lock cylinder housing to release the tabs on the ignition switch

  18.  
  19. Pull the ignition switch out of the lock cylinder housing.
  20.  
  21. Disconnect the connector from the ignition switch.
  22.  

To install:


WARNING
The gears between the ignition switch and the lock cylinder housing must be in the correct position. Failure to do so will cause a misalignment of the gears in the ignition switch and the lock cylinder housing, which may result in a NO START or BATTERY DRAIN.

  1. Verify the alignment of the gear (1) in the ignition switch (2). If gear (1) is not in position shown, turn gear in ignition switch (2) until you reach the correct position.
    NOTE
    In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock.



    Click image to see an enlarged view

    Fig. Verify the alignment of the gear (1) in the ignition switch (2)



    Click image to see an enlarged view

    Fig. In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock

  2.  
  3. Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop.
  4.  
  5. Connect the connector to the ignition switch.
  6.  
  7. Insert the ignition switch into the lock cylinder housing. The tabs on the ignition switch MUST be seated inside the lock cylinder housing for proper installation.
  8.  
  9. Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position - allowing it to spring return into the RUN position.

    Click image to see an enlarged view

    Fig. Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position - allowing it to spring return into the RUN position

  10.  
  11. Align the lock cylinder and install the lock cylinder into the lock cylinder housing.
  12.  
  13. Connect the passlock and key buzzer into the lock housing.
  14.  
  15. Install the steering column trim covers.
  16.  
  17. Install the hush and knee bolster.
  18.  
  19. Enable the SIR system.
  20.  
  21. Connect the negative battery cable.
  22.  

 
label.common.footer.alt.autozoneLogo