Express, Savana, G1500, G2500, G3500, 1998-2005

6.0L V8 VIN U Auto 3

Print

Trouble Code: P0650



Malfunction Indicator Lamp Circuit Malfunction

Possible Causes:



MIL control circuit is open or shorted to ground
 
MIL control circuit is shorted to system power
 
MIL control power circuit is open in the Instrument Cluster
 
MIL (the lamp) is damaged or has failed
 
Instrument Cluster or the PCM has failed
 

Trouble Code: P0651



5-Volt Reference 2 Circuit Malfunction

Possible Causes:



5v VREF circuit is shorted to chassis or sensor ground
 
5v VREF circuit to MAP or TP sensor circuit is shorted to (B+)
 
PCM has failed
 

Trouble Code: P0700



Malfunction Indicator Lamp Circuit Malfunction (TCM)

Possible Causes:



MIL control circuit is shorted to ground
 
Check the TCM for any trouble codes in memory that are responsible for the request to turn on the MIL
 
TCM has failed
 

Trouble Code: P0711



TFT Sensor Range/Performance (4L60-E, 4L80-E)

Possible Causes:



ATF fluid level too low or the fluid is contaminated or burnt
 
TFT sensor is contaminated, damaged or "skewed"
 
PCM has failed
 

Trouble Code: P0712



TFT Sensor Circuit Low Input (4L60-E, 4L80-E)

Possible Causes:



TFT sensor signal circuit is shorted to sensor or chassis ground
 
TFT sensor is damaged or has failed (it may be shorted)
 
PCM has failed
 

Trouble Code: P0713



TFT Sensor Circuit High Input (4L60-E. 4L80-E)

Possible Causes:



TFT sensor signal circuit is open between the sensor and PCM
 
TFT sensor signal circuit is shorted to VREF or system power
 
TFT sensor is damaged or has failed (it may be open)
 
PCM has failed
 

Trouble Code: P0716



A/T Input Shaft Speed Sensor Circuit Malfunction (4L80-E)

Possible Causes:



ISS positive (+) circuit is open, shorted to ground or to power
 
ISS negative (-) circuit is open, shorted to ground or to power
 
ISS terminals are corroded or damaged (check for moisture)
 
ISS signal wires routed too close to the Ignition system cables
 
PCM has failed
 

Trouble Code: P0717



A/T Input Shaft Speed Sensor Low Input (4L80-E)

Possible Causes:



ISS positive (+) circuit is open, shorted to ground or to power
 
ISS negative (-) circuit is open, shorted to ground or to power
 
ISS is damaged or has failed
 
PCM has failed
 
TSB 00-07-30-015 contains a repair procedure for this code
 

Trouble Code: P0719



TCC Brake Switch Circuit Low Input (4L60-E, 4L80-E)

Possible Causes:



TCC brake switch circuit is open or shorted to ground
 
TCC brake switch power circuit is open (check the CRUISE, FAN ALT or other related fuse in underhood junction block)
 
TCC brake switch is out of adjustment or damaged
 
PCM has failed
 

Trouble Code: P0724



TCC Brake Switch High Input (4L60-E, 4L80-E)

Possible Causes:



Check for ABS trouble codes (they can cause this code to set)
 
TCC brake switch circuit is shorted to system power
 
TCC brake switch is out of adjustment or damaged
 
PCM has failed
 

Trouble Code: P0730



Incorrect Gear Ratio (4L80-E)

Possible Causes:



ATF level is too low, or the fluid is burnt or contaminated
 
ISS or OSS signal circuit has an intermittent fault condition
 
Inspect for debris in the transmission pan or internal damaged
 
Possible vehicle overloading, exceeding the trailer towing limit, or towing in overdrive events occurred (discuss with customer)
 

Trouble Code: P0740



TCC Solenoid Circuit Malfunction (4L60-E, 4L65-E)

Possible Causes:



TCC solenoid control circuit is open, shorted to ground or to B+
 
TCC solenoid power circuit is open (test the TRANS fuse)
 
TCC solenoid is damaged or has failed
 
PCM has failed
 
TSB 01-07-30-002C contains a repair procedure for this code
 

Trouble Code: P0742



TCC System Stuck Off - Mechanical (4L60-E)

Possible Causes:



Exhaust orifice in the TCC solenoid valve is clogged
 
Converter clutch apply valve stuck in the "on" (apply) position
 
Valve body gasket is damaged or misaligned
 
Release pass is clogged or restricted
 
Transmission cooler line is bent or restricted
 

Trouble Code: P0751



A/T 1-2 Shift Solenoid - No 1st Or 4th Gear (4L60-E, 4L65-E, 4L80-E)

Possible Causes:



ATF is burnt or contaminated, or the level is incorrect
 
Transmission has an internal damage to the torque converter
 
Shift solenoid valve seals are damaged or leaking
 
Transmission has failed
 

Trouble Code: P0752



A/T 1-2 Shift Solenoid - No 2nd Or 3rd Gear (4L60-E, 4L80-E)

Possible Causes:



ATF is burnt or contaminated, or the level is incorrect
 
Transmission has an internal damage to the torque converter
 
Shift solenoid valve seals are damaged or leaking
 
Transmission has failed
 

Trouble Code: P0753



A/T 1-2 Shift Solenoid Circuit Malfunction (4L60-E, 4L80-E)

Possible Causes:



1-2 shift solenoid control circuit is open or shorted to ground
 
1-2 shift solenoid control circuit is shorted to system power
 
1-2 shift solenoid is damaged or has failed
 
PCM has failed
 
TSB 01-07-30-002C contains a repair procedure for this code
 

Trouble Code: P0756



2-3 Shift Solenoid - No 2nd Or 3rd Gear (4L60-E, 4L65-E)

Possible Causes:



ATF is burnt or contaminated
 
Transmission has plugged or restricted fluid circuits
 
Shift solenoid valve seals are leaking or damaged
 
Transmission has failed
 
TSB 01-07-30-036A contains a repair procedure for this code
 

Trouble Code: P0758



A/T 2-3 Shift Solenoid Circuit Malfunction (4L60-E, 4L80-E)

Possible Causes:



2-3 shift solenoid control circuit is open or shorted to ground
 
2-3 shift solenoid control circuit is shorted to system power
 
2-3 shift solenoid power circuit is open (test the TRANS fuse)
 
2-3 shift solenoid is damaged or has failed
 
PCM has failed
 
TSB 01-07-30-002C contains a repair procedure for this code
 

Trouble Code: P0785



A/T 3-2 Shift Solenoid Circuit Malfunction (4L60-E)

Possible Causes:



3-2 shift solenoid control circuit is open, shorted to ground or shorted to system power
 
3-2 shift solenoid power circuit is open (check the TRANS fuse)
 
3-2 shift solenoid is damaged or has failed
 
PCM has failed
 
TSB 01-07-30-002C contains a repair procedure for this code
 

Trouble Code: P0850



Title: A/T TCC PWM Solenoid Malfunction (4L60-E, 4L65-E)

Possible Causes:



ATF is burnt or contaminated
 
Transmission has an internal malfunction, or the TCC PWM solenoid seal is damaged
 
TCC PWM solenoid has failed, or the Transmission has failed
 

Trouble Code: P1106



MAP Sensor Circuit Intermittent High Input

Possible Causes:



MAP sensor signal circuit is shorted to VREF (intermittent fault)
 
MAP sensor ground circuit is open (intermittent fault)
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1107



MAP Sensor Circuit Intermittent Low Input

Possible Causes:



MAP sensor signal circuit is shorted to VREF (intermittent fault)
 
MAP sensor ground circuit is open (intermittent fault)
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1111



IAT Sensor Circuit Intermittent High Input

Possible Causes:



IAT sensor signal circuit is open (intermittent fault)
 
IAT sensor ground circuit is open (intermittent fault)
 
IAT sensor is damaged (an intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1112



IAT Sensor Circuit Intermittent Low Input

Possible Causes:



IAT sensor signal circuit is open (intermittent fault)
 
IAT sensor ground circuit is open (intermittent fault)
 
IAT sensor is damaged (an intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1114



ECT Sensor Circuit Intermittent Low Input

Possible Causes:



ECT sensor signal circuit shorted to ground (intermittent fault)
 
ECT sensor has failed (possible intermittent shorted condition)
 
PCM has failed
 

Trouble Code: P1115



ECT Sensor Circuit Intermittent High Input

Possible Causes:



ECT sensor signal circuit is open between the sensor and PCM
 
ECT sensor ground circuit is open between sensor and PCM
 
ECT sensor has failed (possible intermittent "open" condition)
 
PCM has failed
 

Trouble Code: P1120



TP Sensor 1 Circuit Malfunction

Possible Causes:



TP1 sensor signal circuit is open, shorted to ground or to power
 
TP1 sensor VREF circuit is open or shorted to ground or to B+
 
TP1 sensor ground circuit has a high resistance condition
 
TP1 sensor is damaged or has failed
 

Trouble Code: P1122



TP Sensor Circuit Intermittent High Input

Possible Causes:



TP sensor signal circuit is shorted to VREF (intermittent fault)
 
TP sensor ground circuit is open (an intermittent fault)
 
TP sensor is damaged or has failed (possible intermittent open)
 
PCM has failed
 

Trouble Code: P1125



Accelerator Position Sensor 1 and 2 Circuit Malfunction

Possible Causes:



APP sensor assembly is damaged, loose or shorted
 
APP1 sensor signal circuit shorted to the APP2 sensor circuit
 
APP 1 or APP2 sensor signal circuit has high resistance
 
APP sensor assembly is damaged or TAC module has failed
 

Trouble Code: P1133



HO2S-11 (Bank 1 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1153



HO2S-21 (Bank 2 Sensor 1) Insufficient Switching

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
Fuel pressure is too high (i.e., causing a rich air fuel mixture)
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal high or low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1154



HO2S-21 (Bank 2 Sensor 1) Transition Time Ratio

Possible Causes:



Air leaks present in the exhaust manifold or the exhaust pipes
 
HO2S may be contaminated (due to improper fuel or silicone)
 
HO2S signal low reference circuit has high resistance
 
HO2S heater element has failed, or the heater circuit is open
 
PCM has failed
 

Trouble Code: P1172



Secondary Fuel Pump Insufficient/No Fuel Flow

Possible Causes:



Fuel tank level is too low (must be within 25-75% to test relay)
 
Secondary F/P relay power circuit is open (test the ENG1 fuse)
 
Secondary F/P relay control circuit is open, shorted to ground or shorted to power
 
Secondary F/P relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1207



FICM PWM Signal To PCM Circuit Malfunction

Possible Causes:



FICM sensor PWM signal circuit is open or shorted to ground
 
FICM is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1208



Fuel Rail Pressure Signal To PCM Circuit Malfunction

Possible Causes:



FICM sensor PWM signal circuit is open or shorted to ground
 
FICM is damaged or it has failed
 
PCM has failed
 

Trouble Code: P1220



TP Sensor 2 Circuit Malfunction

Possible Causes:



TP2 sensor signal circuit is open, shorted to ground or to power
 
TP2 sensor VREF circuit is open, shorted to ground or shorted to system power (B+)
 
TP2 sensor ground circuit has a high resistance condition
 
TP2 sensor is damaged or has failed
 

Trouble Code: P1221



TP Sensor 2 Signal Correlation

Possible Causes:



TP2 sensor connector is contaminated, dirty or contains water
 
TP2 sensor signal, ground or VREF circuit has high resistance
 
TP2 sensor VREF circuit has a high resistance condition
 
TP2 sensor ground circuit has a high resistance condition
 
TP2 sensor is damaged or has failed
 
TAC controller or the throttle body is damaged or has failed
 
TSB 02-06-04-005 contains a repair procedure for this code
 

Trouble Code: P1275



Accelerator Pedal Position Sensor 1 Circuit Malfunction

Possible Causes:



APP1 sensor connector is contaminated, oily or contains water
 
APP1 sensor signal, ground or VREF circuit high resistance
 
APP1 sensor VREF circuit is open, shorted to ground or to B+
 
APP1 sensor signal or ground circuit has high resistance
 
APP1 sensor is damaged or has failed
 
TAC module is damaged or has failed
 

Trouble Code: P1276



Accelerator Pedal Position Sensor 1 Range/Performance

Possible Causes:



APP1 sensor connector is contaminated, oily or contains water
 
APP1 sensor signal circuit is open or shorted to ground
 
APP1 sensor signal circuit is shorted to VREF or system power
 
APP1 sensor ground circuit is open or has high resistance
 
APP1 sensor VREF circuit is open or shorted to ground
 
APP1 sensor is damaged or has failed
 

 
label.common.footer.alt.autozoneLogo