Ford Ranger/Bronco II 1983-1990 Repair Guide

Timing Belts



See Figures 1, 2, 3, 4, 5, 6, 7, 8 and 9

Only the 2.0L and 2.3L (gasoline and diesel) OHC engines use a rubber timing belt. All other engines use a timing chain and/or gears, and no periodic inspection is required.

The 2.0L and 2.3L Ranger engines utilize a timing belt to drive the camshaft from the crankshaft's turning motion and to maintain proper valve timing. Some manufacturer's schedule periodic timing belt replacement to assure optimum engine performance, to make sure the motorist is never stranded should the belt break (as the engine will stop instantly) and for some (manufacturer's with interference motors) to prevent the possibility of severe internal engine damage should the belt break.

Although these engines are not listed as an interference motor (it is not listed by the manufacturer as a motor whose valves might contact the pistons if the camshaft was rotated separately from the crankshaft) the first 2 reasons for periodic replacement still apply. Ford does not publish a replacement interval for these engines, but most belt manufacturers recommend intervals anywhere from 45,000 miles (72,500 km) to 90,000 miles (145,000 km). You will have to decide for yourself if the peace of mind offered by a new belt is worth it on higher mileage engines.

But whether or not you decide to replace it, you would be wise to check it periodically to make sure it has not become damaged or worn. Generally speaking, a severely worn metal chain will show wear as engine performance would drop dramatically, but a damaged or worn rubber belt (which could give out suddenly) may not give as much warning. In general, any time the engine timing cover(s) is(are) removed you should inspect the belt for premature parting, severe cracks or missing teeth. Also, an access plug is provided in the upper portion of the timing cover so that camshaft timing can be checked without cover removal. If timing is found to be off, cover removal and further belt inspection or replacement is necessary.

Click image to see an enlarged view

Fig. Fig. 1: Do not bend, twist or turn the timing belt inside out. Never allow oil, water or steam to contact the belt

Click image to see an enlarged view

Fig. Fig. 2: Check for premature parting of the belt

Click image to see an enlarged view

Fig. Fig. 3: Check if the teeth are cracked or damaged

Click image to see an enlarged view

Fig. Fig. 4: Look for noticeable cracks or wear on the belt face

Click image to see an enlarged view

Fig. Fig. 5: You may only have damage on one side of the belt; if so, the guide could be the culprit

Click image to see an enlarged view

Fig. Fig. 6: Foreign materials can get in between the teeth and cause damage

Click image to see an enlarged view

Fig. Fig. 7: Inspect the timing belt for cracks, fraying, glazing or damage of any kind

Click image to see an enlarged view

Fig. Fig. 8: Damage on only one side of the timing belt may indicate a faulty guide

Click image to see an enlarged view

Fig. Fig. 9: ALWAYS replace the timing belt at the interval specified by the manufacturer


  1. Locate and carefully remove the access plug from the upper portion of the timing cover.

When turning the engine over by hand, ALWAYS rotate the crankshaft in the proper direction of rotation, otherwise the timing belt might jump one or more teeth due to the configuration of the belt tensioner.

  1. Turn the engine CLOCKWISE (in the normal direction of rotation) to set the engine at Top Dead Center (TDC) of the No. 1 cylinder by aligning the O mark on the belt cover with the O mark on the crankshaft pulley.

If no timing mark is visible through the access cover when the O marks on the crank pulley and cover are aligned, the engine may be on No. 1 exhaust stroke and not the compression stroke (the camshaft is 180° away from No. 1 TDC). If so, the crankshaft must be rotated one full turn to bring the No. 1 piston back to the top and the camshaft around to close the No. 1 intake and exhaust valves.

  1. With the O marks aligned, look through the access hole in the cover to assure that the timing mark on the camshaft sprocket aligns with the pointer on the inner belt cover. If the belt timing is incorrect, the timing cover and belt must be removed for further inspection, possible replacement and correct installation. For more details, please refer to Engine & Engine Rebuilding of this guide.
  3. If timing is correct, re-install the access plug.