See Figures 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 and 13
The Evaporative Emission Control System (EECS) is designed to prevent fuel tank vapors from being emitted into the atmosphere. Gasoline vapors are absorbed and stored by a fuel vapor charcoal canister. The charcoal canister absorbs the gasoline vapors and stores them until certain engine conditions are met and the vapors can be purged and burned by the engine.
The charcoal canister purge cycle is controlled by a thermostatic vacuum switch, a timed vacuum source or by a solenoid valve the receives its instruction from the engine management system. The thermostatic switch is installed in the coolant passage and prevents canister purge when engine operating temperature is below 115°F (46°C). The timed vacuum source uses a manifold vacuum-controlled diaphragm to control canister purge. When the engine is running, full manifold vacuum is applied to the top tube of the purge valve which lifts the valve diaphragm and opens the valve. The solenoid valve is usually mounted on or near the intake manifold. In general, none of the systems, regardless of type, allow canister purge below 115°F (46°C).
A vent located in the fuel tank, allows fuel vapors to flow to the charcoal canister. A tank pressure control valve, used on high altitude applications, prevents canister purge when the engine is not running. The fuel tank cap does not normally vent to the atmosphere but is designed to provide both vacuum and pressure relief.
Poor engine idle, stalling and poor driveability can be caused by a damaged canister or split, damaged or improperly connected hoses.
Evidence of fuel loss or fuel vapor odor can be caused by a liquid fuel leak:
- Apply a length of hose to the lower tube of the purge valve assembly and attempt to blow air through it. There should be little or no air should passing into the canister.
If the canister is equipped with a constant purge hole, a small amount of air will pass into the canister.
- Using a hand-held vacuum pump, apply a vacuum of 15 in. Hg (51 kPa) to the control vacuum (upper) tube. If the vacuum does not hold for at least 20 seconds, the diaphragm is leaking. Replace the canister.
- If the diaphragm holds vacuum, attempt to blow air through the hose connected to the PCV tube while vacuum is still being applied. An increase of air should be observed. If no increase is noted, the canister must be replaced.
See Figure 14
- Attach a length of hose to the tank side of the valve assembly and try to blow air through it. Little or no air should pass into the canister.
- Using a hand-held vacuum pump, apply vacuum equivalent to 15 in. Hg (51 kPa) to the control vacuum tube. If the diaphragm does not hold vacuum, the diaphragm is leaking. Replace the valve.
- If the diaphragm holds vacuum, attempt to blow air through the hose connected to the valve while vacuum is still being applied. Air should pass. If no air is noted, the valve must be replaced.
- With engine temperature below 100°F (38°C), apply vacuum to the manifold side of the switch. The switch should hold vacuum.
- Start and continue to run the engine until the engine temperature increases above 122°F (50°C). The vacuum should drop off.
- Replace the switch if it fails either test.
REMOVAL & INSTALLATION
See Figures 15, 16 and 17
- Tag and disconnect the hoses from the canister.
- Remove the vapor canister retaining nut.
- Remove the canister from the vehicle.
- Install the canister. If necessary refer to the vehicle emission control label, located in the engine compartment for proper routing of the vacuum hoses.
- Drain the cooling system to below the switch level.
- Tag and disconnect the vacuum hoses from the switch.
- Remove the thermostatic vacuum switch.
- Install the thermostatic vacuum switch. Make sure to apply sealer to the switch threads.
- Connect the vacuum hoses.
- Refill the cooling system.
See Figures 18, 19 and 20
- Disconnect the negative battery cable.
- Disconnect the electrical connectors and hoses from the solenoid.
- Pull the solenoid away from the bracket and remove the assembly.
- Install the solenoid to the bracket by sliding it into place.
- Connect the electrical connectors and the hoses.
- Connect the negative battery cable.