GM Blazer/Jimmy/Typhoon/Bravada 1983-1993 Repair Guide



Ignition timing is the measurement, in degrees of crankshaft rotation, of the point at which the spark plugs fire in each of the cylinders. It is measured in degrees before or after Top Dead Center (TDC) of the compression stroke.

Because it takes a fraction of a second for the spark plug to ignite the mixture in the cylinder, the spark plug must fire a little before the piston reaches TDC. Otherwise, the mixture will not be completely ignited as the piston passes TDC and the full power of the explosion will not be used by the engine.

The timing measurement is given in degrees of crankshaft rotation before the piston reaches TDC (BTDC). If the setting for the ignition timing is 5° BTDC, the spark plug must fire 5° before each piston reaches TDC. This only holds true, however, when the engine is at idle speed.

As the engine speed increases, the pistons go faster. The spark plugs have to ignite the fuel even sooner if it is to be completely ignited when the piston reaches TDC. To do this, distributors have various means of advancing the spark timing as the engine speed increases. On some earlier model vehicles, this is accomplished by centrifugal weights within the distributor along with a vacuum diaphragm mounted on the side of the distributor. Later model vehicles are equipped with Electronic Spark Timing (EST) in which no vacuum or mechanical advance is used. Instead, the EST system makes all timing changes electronically based on signals from various sensors.

If the ignition is set too far advanced (BTDC), the ignition and expansion of the fuel in the cylinder will occur too soon and tend to force the piston down while it is still traveling up. This causes engine ping. If the ignition spark is set too far retarded, after TDC (ATDC), the piston will have already passed TDC and have started on its way down when the fuel is ignited. This will cause the piston to be forced down for only a portion of its travel. This will result in poor engine performance and lack of power.

Timing marks consist of a notch on the rim of the crankshaft pulley and a scale of degrees attached to the front of the engine (often on the engine front cover). The notch corresponds to the position of the piston in the number 1 cylinder. A stroboscopic (dynamic) timing light is used, which is hooked into the circuit of the No. 1 cylinder spark plug. Every time the spark plug fires, the timing light flashes. By aiming the timing light at the timing marks while the engine is running, the exact position of the piston within the cylinder can be easily read since the stroboscopic flash makes the mark on the pulley appear to be standing still. Proper timing is indicated when the notch is aligned with the correct number on the scale.

There are three basic types of timing lights available. The first is a simple neon bulb with two wire connections (one for the spark plug and one for the plug wire, connecting the light in series). This type of light is quite dim, and must be held closely to the marks to be seen, but it is quite inexpensive. The second type of light is powered by the car's battery. Two alligator clips connect to the battery terminals, while a third wire connects to the spark plug with an adapter. This type of light is more expensive, but the xenon bulb provides a nice bright flash which can even be seen in sunlight. The third type replaces the battery source with 110 volt house current, but still attaches to the No. 1 spark plug wire in order to determine when the plug is fired. Some timing lights have other functions built into them, such as dwell meters, tachometers, or remote starting switches. These are convenient, in that they reduce the tangle of wires under the hood, but may duplicate the functions of tools you already have.

Never pierce a spark plug wire in order to attach a timing light or perform tests. The pierced insulation will eventually lead to an electrical arc and related ignition troubles.

Since your truck has electronic ignition, you should use a timing light with an inductive pickup. This pickup simply clamps onto the No. 1 spark plug wire, eliminating the adapter. It is not susceptible to cross-firing or false triggering, which may occur with a conventional light, due to the greater voltages produced by electronic ignition.