Log In
Search suggestions

    My Vehicles

    2004 Buick Park Avenue Ultra 3.8L FI SC OHV 6cyl

    My Store

    1720 S RIDGEWOOD A
    (386) 427-1210

    CLOSED Open tomorrow at 7:30 AM

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    GM Buick/Oldsmobile/Pontiac/Full-Size 1975-1990 Repair Guide

    Timing

    Print

    See Figures 1 and 2

    Ignition timing is the measurement, in degrees of crankshaft rotation, of the point at which the spark plugs fire in each of the cylinders. It is measured in degrees before or after Top Dead Center (TDC) of the compression stroke.

    Because it takes a fraction of a second for the spark plug to ignite the mixture in the cylinder, the spark plug must fire a little before the piston reaches TDC. Otherwise, the mixture will not be completely ignited as the piston passes TDC and the full power of the explosion will not be used by the engine.

    The timing measurement is given in degrees of crankshaft rotation before the piston reaches TDC (BTDC). If the setting for the ignition timing is 5° BTDC, the spark plug must fire 5° before each piston reaches TDC. This only holds true, however, when the engine is at idle speed.

    As the engine speed increases, the pistons go faster. The spark plugs have to ignite the fuel even sooner if it is to be completely ignited when the piston reaches TDC. To do this, the distributor has two means to advance the timing of the spark as the engine speed increases. This is accomplished by centrifugal weights within the distributor, and a vacuum diaphragm mounted on the side of the distributor (early models). The later model engines control the spark timing through the ECM (Electronic Control Module).

    If the ignition is set too far advanced (BTDC), the ignition and expansion of the fuel in the cylinder will occur too soon and cause engine ping. If the ignition spark is set too far retarded, after TDC (ATDC), the piston will have already passed TDC and started on its way down when the fuel is ignited. This will cause the piston to be forced down for only a portion of its travel. This will result in poor engine performance and lack of power.

    Timing marks consist of a notch on the rim of the crankshaft pulley and a scale of degrees attached to the front of the engine. The notch corresponds to the position of the piston in the number 1 cylinder. A stroboscopic (dynamic) timing light is used, which is hooked into the circuit of the No. 1 cylinder spark plug. Every time the spark plug fires, the timing light flashes. By aiming the timing light at the timing marks, the exact position of the piston within the cylinder can be read, since the stroboscopic flash makes the mark on the pulley appear to be standing still. Proper timing is indicated when the notch is aligned with the correct number on the scale.



    Click image to see an enlarged view

    Fig. Fig. 1: Timing indicator, located just above the harmonic balancer

    There are three basic types of timing lights available. The first is a simple neon bulb with two wire connections (one for the spark plug and one for the plug wire, connecting the light in series). This type of light is quite dim, and must be held closely to the marks to be seen, but it is inexpensive. The second type of light operates from the vehicle's battery. Two alligator clips connect to the battery terminals, while a third wire connects to the spark plug with an adapter. This type of light is more expensive, but the xenon bulb provides a nice bright flash which can even be seen in sunlight. The third type replaces the battery source with 110 volt house current. Some timing lights have other functions built into them, such as dwell meters, tachometers, or remote starting switches. These are convenient, in that they reduce the tangle of wires under the hood, but may duplicate the functions of the tools you already have.

    If your vehicle has electronic ignition, you should use a timing light with an inductive pickup. This pickup simply clamps onto the No. 1 spark plug wire, eliminating the adapter. It is not susceptible to cross firing or false triggering, which may occur with a conventional light, due to the greater voltages produced by the electronic ignition.



    Click image to see an enlarged view

    Fig. Fig. 2: Timing indicator on an Olds 307 (VIN Y); all models similar

    INSPECTION & ADJUSTMENT



    Non-ESC Models

    The non-ESC (Electronic Spark Controlled) vehicles are equipped with a vacuum advance unit at the distributor.

    1. Warm the engine to normal operating temperature. Shut off the engine and connect the timing light to the No. 1 spark plug, located on the left (driver's side) front of the engine.
    2.  

    DO NOT, under any circumstances, pierce a spark plug wire to hook up the light. Once the insulation is broken, voltage will jump to the nearest ground, and the spark plug will not fire properly.

    1. Clean off the timing marks and mark the pulley or damper notch and the timing scale with white chalk or paint. The timing notch on the damper or pulley can be elusive. Bump the engine around with the starter or turn the crankshaft with a wrench on the front pulley bolt to get it to an accessible position.
    2.  
    3. Disconnect and plug the vacuum advance hose at the distributor, to prevent any distributor advance. The vacuum line is the rubber hose connected to the metal cone-shaped canister on the side of the distributor. A short screw, pencil, or a golf tee can be used to plug the hose.
    4.  
    5. Start the engine and adjust the idle speed to that specified in the Tune-Up Specifications chart. If the chart differs from the underhood emissions label, use the specs on the label. Some vehicles require that the timing be set with the transmission in Neutral. You can disconnect the idle solenoid, if any, to get the speed down. Otherwise, adjust the idle speed screw. This is to prevent any centrifugal advance of timing in the distributor.
    6.  

    On 1975-77 HEI systems, the tachometer connects to the TACH terminal on the distributor and to a ground. For 1978 and later models, all tachometer connections are to the TACH terminal. Some tachometers must connect to the TACH terminal and to the positive battery terminal. Some tachometers won't work at all with HEI. Consult the tachometer manufacturer if the instructions supplied with the unit do not give the proper connection.


    CAUTION
    Never ground the HEI TACH terminal; serious system damage will result, including module burnout.

    1. Aim the timing light at the timing marks. Be careful not to touch the fan, which may appear to be standing still. Keep your clothes and hair, and the light's wires clear of the fan, belts, and pulleys. If the pulley or damper notch is not aligned with the proper timing mark (see the Tune-Up Specifications chart or Underhood Emissions Label), the timing will have to be adjusted.
    2.  

    TDC or Top Dead Center corresponds to 0 degrees, Before Top Dead Center or BTDC may also be shown as BEFORE; A, ATDC, or After Top Dead Center, may be shown as AFTER.

    1. Loosen the distributor base clamp locknut. You can buy special wrenches which make this task a lot easier on V8s. Turn the distributor slowly to adjust the timing, holding it by the body and not the cap. Turn the distributor in the direction of rotor rotation (found in the Firing Order illustration) to retard, and against the direction to advance.
    2.  

    The 231 and 252 V6 engines have two timing marks on the crankshaft pulley. One timing mark is1/8in. (3.1mm) wide and the other, is1/16in. (1.6mm) wide. The smaller mark is used for setting the timing with a hand-held timing light. The larger mark is used with the magnetic probe and is only of use to a professional mechanic. Make sure you set the timing using the smaller mark.

    1. Tighten the locknut. Check the timing, in case the distributor moved as you tightened it.
    2.  
    3. Replace the distributor vacuum hose, if removed. Correct the idle speed.
    4.  
    5. Shut off the engine and disconnect the light.
    6.  

    ESC Models

    See Figure 3

    ESC (Electronic Spark Control) equipped models do not have a vacuum advance unit on the distributor. The spark is controlled by the ECM (Electronic Control Module). ESC distributors have a four wire connector instead of a vacuum advance unit.

    1. The timing marks are the same as the non-ESC vehicles. Refer to the underhood sticker for proper timing procedures and specifications. If there is no sticker, follow these procedures to adjust ignition timing.
    2.  
    3. Start the engine and allow it to reach normal operating temperature.
    4.  
    5. If equipped, make sure the air conditioner is turned OFF.
    6.  
    7. Ground the Diagnostic terminal of the ALDL (Assembly Line Diagnostic Link) located under the dash panel on the left (driver) side. Using a small piece of wire, ground the A to B terminal as in the ALDL terminal illustration in this section.
    8.  



    Click image to see an enlarged view

    Fig. Fig. 3: For ESC equipped vehicles, ground the A and B terminals at the ALDL. This is usually located next to the fuse panel.

    1. Using a timing light, set the timing at the specified rpm by loosening the distributor hold-down clamp and rotating the distributor until the specified timing is obtained at the timing marks on the crankshaft pulley.
    2.  
    3. Tighten the hold-down clamp and recheck the timing to ensure the distributor has not moved during this procedures.
    4.  
    5. With the engine RUNNING, remove the ground wire at the ALDL under the dash panel. The engine should be running so no trouble codes are stored in the ECM.
    6.  
    7. Make any necessary carburetor adjustments and reconnect any removed vacuum lines.
    8.  

     
    AutoZone Logo