GM Century/Lumina/Grand Prix/Intrigue 1997-2000

PCV Valve

Print

The Crankcase Ventilation Valve, also known as the Positive Crankcase Ventilation or PCV Valve, is part of the system used to consume crankcase vapors in the combustion process instead of venting them to atmosphere. Fresh air from the throttle body is supplied to the crankcase, mixed with blow-by gases, and then passed through the crankcase ventilation valve into the intake manifold system. The primary control for this system is the crankcase ventilation valve which meters the flow at a rate depending on inlet vacuum. To maintain idle quality, the valve restricts the flow when inlet vacuum is low (idle or low rpm operation). If abnormal operating conditions arise, the system is designed to allow excessive amounts of blow-by gases to back flow through the crankcase vent into the throttle body to be consumed by normal combustion.

A plugged valve may cause a rough idle, stalling or slow idle speed, oil leaks and sludge in the engine. A leaking valve would cause a rough idle, stalling and high idle speed. Another area to watch is the rubber grommet which retains most PCV valves. These deteriorate from their constant exposure to engine oil and heat. If the grommet shows signs of cracking or has deteriorated to the point where the PCV valve is not a tight fit, it should be replaced.

The crankcase ventilation valve should be inspected every 30,000 miles (50,000 km) for proper operation. To check, remove the valve, and operate the engine at idle. Place your thumb over the end of the valve to check for vacuum. If there is no vacuum, check for a plugged hose, a clogged manifold port or suspect a failed valve. Turn off the engine and remove the valve and shake it. Listen for the rattle of the check needle inside the valve. If the valve does not rattle, replace it

In general, crankcase ventilation valve service is relatively simple. While the valve can be cleaned in many cases, replacement is recommended.

REMOVAL & INSTALLATION



3.1L (VIN M) and 3.4L (VIN E) Engines
  1. Locate the vacuum hoses that run to the fuel pressure regulator and the Positive Crankcase Ventilation (PCV) valve. They should run parallel to each other. It may be necessary to disconnect both hoses, depending on the model and the brackets. The vacuum hose to the ventilation valve terminates on the valve which is pressed into a rubber grommet mounted on one of the valve rocker covers.
  2.  



Click image to see an enlarged view

Fig. Location of the PCV valve-3.1L (VIN M) and 3.4L (VIN E) engines



Click image to see an enlarged view

Fig. The PCV valve on this 3.1L engine was contaminated with and oil/coolant mix that resulted from intake manifold gasket failure



Click image to see an enlarged view

Fig. A new PCV is connected to its vacuum hose then simply inserted back into the rubber grommet in the rocker arm cover

  1. Pull the vacuum hose off of the valve. The valve should be easily pulled from its grommet.
  2.  
  3. Install the replacement valve into the grommet. Make sure it is seated properly so there will be no vacuum leaks.
  4.  
  5. Connect the vacuum hose(s) to the crankcase valve as well as the fuel pressure regulator, if removed. Verify the hoses are secure.
  6.  

3.4L (VIN X) Engine
  1. Locate the crankcase ventilation valve in its location in its molded rubber connection on the lower side of the intake manifold.
  2.  
  3. Remove the valve from its vacuum hose connection.
  4.  



Click image to see an enlarged view

Fig. Crankcase ventilation pipe routing and valve location-3.4L (VIN X) engine

To install:

  1. Install the replacement valve. Make sure it is seated properly so there will be no vacuum leaks.
  2.  
  3. Connect the vacuum hose to the crankcase valve. Test run the engine to verify no vacuum leaks.
  4.  

3.8L (VIN K) Engine
  1. The cosmetic/acoustic engine cover is called the fuel injector sight shield. Remove this cover by first turning counter-clockwise the tube/oil fill cap from the valve rocker arm cover. Lift the fuel injector sight shield up at the front and slide the tab out of the engine bracket.
  2.  



Click image to see an enlarged view

Fig. The engine cover shown here must be removed for almost any engine maintenance. Dirt that collects around the oil fill tube opening must be removed or it will fall into the engine when the cover is removed



Click image to see an enlarged view

Fig. The plastic oil fill tube is the primary cover retainer. Twist the plastic oil fill tube to disengage it. You can see how dirt and debris, if not cleaned off, could easily enter the engine



Click image to see an enlarged view

Fig. Disengage the cover's rear tab from the metal bracket on the back side of the engine



Click image to see an enlarged view

Fig. Remove the cover and set aside in a safe place. Install the oil fill tube temporarily to keep dirt out of the engine



Click image to see an enlarged view

Fig. On the 3.8L (VIN K) engine, you must first remove the MAP sensor to access the crankcase ventilation valve



Click image to see an enlarged view

Fig. On this 3.8L engine, after the MAP sensor is unclipped, the plastic PCV cover needs about 1 / 8 turn to disengage it from the base



Click image to see an enlarged view

Fig. The PCV valve is seated in the lower housing and is retained by a silicone O-ring



Click image to see an enlarged view

Fig. View of the PCV valve and O-ring seal once removed from the 3.8L (VIN K) engine

  1. Locate the Manifold Absolute Pressure (MAP) sensor at the end of the intake manifold. Remove the MAP sensor by disconnecting the electrical connector. Carefully bend the locking tabs holding the MAP sensor to the PCV valve cover just enough to remove the sensor. Pull the MAP sensor straight out of the PCV valve cover.
  2.  
  3. Use a 16mm socket to press the access cover down and rotate 1 / 4 turn counter-clockwise. Remove the access cover.
  4.  
  5. Remove the PCV valve and the O-ring from the intake manifold.
  6.  

To install:

  1. Inspect the O-ring. It should be replaced, if necessary. Install the replacement PCV valve. Install the access cover.
  2.  
  3. Inspect the seal on the MAP sensor. It should be replaced, if necessary. Position the MAP Sensor to the PCV cover. Make sure the locking tabs engage to hold the MAP sensor to the PCV cover. Plug in the electrical connector.
  4.  
  5. Insert the tab of the fuel injector sight shield under the engine bracket. Place the hole of the shield onto the oil fill neck of the valve rocker arm cover. Install the tube/oil fill cap onto the valve rocker arm cover and twist clockwise in order to lock.
  6.  

3.8L (VIN 1) Engine
  1. The cosmetic engine cover, also called the fuel injector sight shield, must be removed. Remove this cover by first turning counter-clockwise the tube/oil fill cap from the valve rocker arm cover. Remove the nut holding the shield to the fuel injector rail brace std. Lift the fuel injector sight shield up at the front and slide the tab out of the engine bracket.
  2.  
  3. On this engine, the crankcase ventilation valve is under an access cover at the throttle body end of the intake manifold. The cover is under a small pressure from a spring underneath the cover. While holding down the valve access cover, remove the two cover bolts.
  4.  



Click image to see an enlarged view

Fig. On the 3.8L (VIN 1) supercharged engine, the crankcase ventilation valve is found under a cover plate

  1. Remove the access cover, then remove the crankcase ventilation valve, the spring and O-ring.
  2.  

To install:

  1. Install the replacement valve with a new O-ring. Position the spring and install the cover.
  2.  
  3. While holding down the ventilation valve access cover, install the cover retaining bolts.
  4.  
  5. Install the engine cover by inserting the tab of the cover under the engine bracket. Place the hole of the cover onto the oil fill neck of the rocker arm cover.
  6.  
  7. Install the tube/oil fill cap into the rocker arm cover and twist clockwise in order to lock.
  8.  
  9. Install the nut holding the cover to the fuel injector rail brace stud and snug down to just 18 inch lbs. (2 Nm).
  10.  

 
label.common.footer.alt.autozoneLogo