GM: Electra/Park Avenue/Ninety-Eight 1990-1993

How To Use This Guide

Print

Repair information for the Oldsmobile Ninety Eight and Buick Electra and Park Avenue is intended to teach you about the inner workings of your car and save you money on its upkeep.

The first two Sections will be the most used, since they contain maintenance and tune-up information and procedures. Studies have shown that a properly-tuned and maintained car can get at least 10% better gas mileage (which translates into lower operating costs) and periodic maintenance will catch minor problems before they turn into major repair bills. The remaining Sections deal with more complex systems of your car. Operating systems from engine through brakes are covered to the extent that the average do-it-yourselfer becomes mechanically involved.

A secondary purpose of this guide is a reference guide for owners who want to understand their car and/or their mechanics better. In this case, no tools at all are required. Knowing just what a particular repair job requires in parts and labor time will allow you to evaluate whether or not you're getting a fair price quote and help decipher itemized bills from a repair shop.

Before attempting any repairs or service on your car, read through the entire procedure outlined in the appropriate Section. This will give you the overall view of what tools and supplies will be required. There is nothing more frustrating than having to walk to the bus stop on Monday morning because you were short one gasket on Sunday afternoon. Read ahead and plan ahead. Each operation should be approached logically and all procedures thoroughly understood before attempting any work. Some special tools that may be required can often be rented from local automotive jobbers or places specializing in renting Tools and Equipment. Check the yellow pages of your local phone book.

All Sections contain adjustments, maintenance, removal and installation procedures, and overhaul procedures. When overhaul is not considered practical, you will learn how to remove the failed part and then how to install its replacement. In this way, you at least save the labor costs. Backyard overhaul of some components (such as the alternator or water pump) is just not practical, but the removal and installation procedure is often simple and well within the capabilities of the average car owner.

Two basic mechanic's rules should be mentioned here. First, whenever the left side of the car or engine is referred to, it is meant to specify the driver'S side of the car. Conversely, the right side of the car means the passenger'S side. Second, all screws and bolts are removed by turning counterclockwise, and tightened by turning clockwise.

Safety is always the most important rule. Constantly be aware of the dangers involved in working on or around an automobile and take proper precautions to avoid the risk of personal injury or damage to the vehicle. See `servicing your vehicle safely' in this Section, and the safety notice on the acknowledgment page before attempting any service procedures and pay attention to the instructions provided. There are 3 common mistakes committed when working mechanically:

Incorrect order of assembly, disassembly or adjustment. When taking something apart or putting it together, doing things in the wrong order usually just costs you extra time; however it can break something. Read the entire procedure before beginning disassembly. Do everything in the order in which the instructions say you should do it, even if you can't immediately see a reason for it. When you're taking apart something that is fairly complex, you might want to draw a picture of (or photograph) how it looks at points during disassembly in order to make sure you get everything back in its proper position. Exploded views are supplied whenever possible, but sometimes the job requires more attention to detail than an illustration provides. When making adjustments (especially tune-up adjustments), do them in order. One adjustment often affects another and you cannot expect satisfactory results unless each adjustment is made only when it cannot be changed by any other.

Overtorquing (or undertorquing) nuts and bolts. While it is more common for overtorquing to cause damage, undertorquing can cause a fastener to vibrate loose and cause serious damage, especially when dealing with aluminum parts. Pay attention to torque specifications and utilize a torque wrench when assembling. If a torque figure is not available remember that, if you are using the right tool to do the job, you will probably not have to strain yourself to get a fastener tight enough. The pitch of most threads is so slight that the tension you put on the wrench will be multiplied many times in actual force on what you are tightening. A good example of how critical torque is can be seen in the case of spark plug installation, especially where you are putting the plug into an aluminum cylinder head. Too little torque can fail to crush the gasket, causing leakage of combustion gases and consequent overheating of the plug and engine parts. Too much torque can damage the threads or distort the plug, which changes the spark gap at the electrode. Since more and more manufacturers are using aluminum in their engine and chassis parts to save weight, a torque wrench should be in any serious do-it-yourselfer's tool box.

Incidentally, there are various commercial chemical products available for ensuring that fasteners won't come loose; a common brand is Loctite®. Read the label on the package and make sure the product is compatible with the materials, fluids, etc. involved before choosing one.

Crossthreading. This occurs when a threaded fastener is screwed into a nut or casting at the wrong angle and forced, causing the threads to become damaged. Crossthreading is more likely to occur if access is difficult. It helps to clean and lubricate fasteners, and to start threading with the part to be installed going straight in, using just your fingers initially. If you encounter resistance, unscrew the part and start over again at a different angle until it can be inserted and turned several times without much effort. Keep in mind that many parts, especially spark plugs, use tapered threads so that gentle turning will automatically bring the part you're threading to the proper angle if you don't force it or resist a change in angle. Don't put a wrench on the part until it's been turned in a couple of times by hand. If you suddenly encounter resistance and the part has not seated fully, don't force it. Pull it back out and make sure it's clean and threading properly. Always take your time and be patient; once you have some experience, working on your car will become an enjoyable hobby.

 
label.common.footer.alt.autozoneLogo