BASIC OPERATING PRINCIPLES
The battery is the first link in the chain of mechanisms which work together to provide cranking of the automobile engine. In most modern vehicles, the battery is a lead/acid electrochemical device consisting of six 2v subsections (cells) connected in series so the unit is capable of producing approximately 12v of electrical pressure. Each subsection consists of a series of positive and negative plates held a short distance apart in a solution of sulfuric acid and water.
The two types of plates are of dissimilar metals. This sets-up a chemical reaction, and it is this reaction which produces current flow from the battery when its positive and negative terminals are connected to an electrical accessory such as a lamp or motor. The continued transfer of electrons would eventually convert the sulfuric acid to water, and make the two plates identical in chemical composition. As electrical energy is removed from the battery, its voltage output tends to drop. Thus, measuring battery voltage and battery electrolyte composition are two ways of checking the ability of the unit to supply power. During engine cranking, electrical energy is removed from the battery. However, if the charging circuit is in good condition and the operating conditions are normal, the power removed from the battery will be replaced by the alternator which will force electrons back through the battery, reversing the normal flow, and restoring the battery to its original chemical state.Starting System
The battery and starting motor are linked by very heavy electrical cables designed to minimize resistance to the flow of current. Generally, the major power supply cable that leaves the battery goes directly to the starter, while other electrical system needs are supplied by a smaller cable. During starter operation, power flows from the battery to the starter and is grounded through the vehicle's frame/body or engine and the battery's negative ground strap.
The starter is a specially designed, direct current electric motor capable of producing a great amount of power for its size. One thing that allows the motor to produce a great deal of power is its tremendous rotating speed. It drives the engine through a tiny pinion gear (attached to the starter's armature), which drives the very large flywheel ring gear at a greatly reduced speed. Another factor allowing it to produce so much power is that only intermittent operation is required of it. Thus, little allowance for air circulation is necessary, and the windings can be built into a very small space.
The starter solenoid is a magnetic device which employs the small current supplied by the start circuit of the ignition switch. This magnetic action moves a plunger which mechanically engages the starter and closes the heavy switch connecting it to the battery. The starting switch circuit usually consists of the starting switch contained within the ignition switch, a neutral safety switch or clutch pedal switch, and the wiring necessary to connect these in series with the starter solenoid or relay.
The pinion, a small gear, is mounted to a one way drive clutch. This clutch is splined to the starter armature shaft. When the ignition switch is moved to the START position, the solenoid plunger slides the pinion toward the flywheel ring gear via a collar and spring. If the teeth on the pinion and flywheel match properly, the pinion will engage the flywheel immediately. If the gear teeth butt one another, the spring will be compressed and will force the gears to mesh as soon as the starter turns far enough to allow them to do so. As the solenoid plunger reaches the end of its travel, it closes the contacts that connect the battery and starter, then the engine is cranked.
As soon as the engine starts, the flywheel ring gear begins turning fast enough to drive the pinion at an extremely high rate of speed. At this point, the one-way clutch begins allowing the pinion to spin faster than the starter shaft so that the starter will not operate at excessive speed. When the ignition switch is released from the starter position, the solenoid is de-energized, and a spring pulls the gear out of mesh interrupting the current flow to the starter.
Some starters employ a separate relay, mounted away from the starter, to switch the motor and solenoid current on and off. The relay replaces the solenoid electrical switch, but does not eliminate the need for a solenoid mounted on the starter used to mechanically engage the starter drive gears. The relay is used to reduce the amount of current the starting switch must carry.Charging System
The automobile charging system provides electrical power for operation of the vehicle's ignition system, starting system and all electrical accessories. The battery serves as an electrical surge or storage tank, storing (in chemical form) the energy originally produced by the engine driven generator. The system also provides a means of regulating output to protect the battery from being overcharged and to avoid excessive voltage to the accessories.
The storage battery is a chemical device incorporating parallel lead plates in a tank containing a sulfuric acid/water solution. Adjacent plates are slightly dissimilar, and the chemical reaction of the two dissimilar plates produces electrical energy when the battery is connected to a load such as the starter motor. The chemical reaction is reversible, so that when the generator is producing a voltage (electrical pressure) greater than that produced by the battery, electricity is forced into the battery, and the battery is returned to its fully charged state.
Newer automobiles use alternating current generators or alternators, because they are more efficient, can be rotated at higher speeds, and have fewer brush problems. In an alternator, the field usually rotates while all the current produced passes only through the stator winding. The brushes bear against continuous slip rings. This causes the current produced to periodically reverse the direction of its flow. Diodes (electrical one way valves) block the flow of current from traveling in the wrong direction. A series of diodes is wired together to permit the alternating flow of the stator to be rectified back to 12 volts DC for use by the vehicle's electrical system.
The voltage regulating function is performed by a regulator. The regulator is often built in to the alternator; this system is termed an integrated or internal regulator.