GM Lumina/Grand Prix/Cutlass Supreme/Regal 1988-1996

Instrument Panel and Pad

Print

PRECAUTIONS



When handling a part that has an "ESD-sensitive'' sticker warning of Electrostatic Discharge (it looks like a hand inside a black triangle with a white stripe through it), follow these guidelines to reduce any possible buildup of electrostatic charge:



If replacing a part that has the sticker, do not open the package until just prior to installation. Before removing the part from its package, ground the package to a good ground on the car.
 
Avoid touching the electrical terminals of the component.
 
Always touch a good ground before handling a part with the sticker. This should be repeated while handling the part; do it more often when sliding across the seat, sitting from the standing position, or after walking.
 


CAUTION
Properly disarm the air bag on vehicles equipped with the Supplemental Restraint System (SRS). Failure to do so can cause serious injury.

REMOVAL & INSTALLATION



Cutlass Supreme
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the instrument panel pad:
    1. Open the glove box door, remove the lower storage compartment, remove the revealed screws, and remove the defroster grille and deflector.
    2.  
    3. Remove the screws inside the defroster opening and remove the instrument cluster trim plate.
    4.  
    5. Remove the screws at the sides of the cluster opening and remove the cluster. Remove the Head-Up Display retaining screws behind the cluster.
    6.  
    7. Lift the pad and disconnect the Daytime Running Lamps connector, speaker wiring and glovebox lamp switch.
    8.  
    9. Remove the upper pad from the instrument panel.
    10.  

  4.  
  5. Remove the speakers and radio.
  6.  
  7. Remove the air outlet trim plates and climate control system switch panel.
  8.  
  9. Remove the ashtray or sport pod housing on International Series.
  10.  
  11. Remove the left and right side sound insulators.
  12.  
  13. Remove the ALDL connector and allow it to dangle below the instrument panel.
  14.  
  15. Remove the steering column trim plate and lower the steering column.
  16.  
  17. Remove the courtesy lights.
  18.  
  19. Remove the parking brake release handle and allow it to dangle below.
  20.  
  21. Remove the screws fastening the fuse block and position the fuse block aside.
  22.  
  23. Remove the screws holding the main ventilation duct.
  24.  
  25. Remove the nut holding the wiring harness clip.
  26.  
  27. Remove the glove box lamp.
  28.  
  29. Remove the screws at both bottom ends of the instrument panel.
  30.  
  31. Remove the screws at the top of the instrument panel and at the steering column support.
  32.  
  33. Have a helper assist you, and remove the instrument panel assembly from the vehicle.
  34.  

To install:
  1. Carefully install the instrument panel to the vehicle. Be sure to clear all wiring, etc.
  2.  
  3. Install the screws at the steering column support, the top of the instrument panel, and at the bottom of both sides of the instrument panel.
  4.  
  5. Install the glovebox lamp.
  6.  
  7. Install the nut holding the wiring harness clip.
  8.  
  9. Install the screws holding the main ventilation duct.
  10.  
  11. Install the fuse block and parking brake release handle.
  12.  
  13. Install the courtesy lights.
  14.  
  15. Secure the steering column and install the trim plate.
  16.  
  17. Install the ALDL connector.
  18.  
  19. Install the left and right side sound insulators.
  20.  
  21. Install the ashtray or sport pod housing.
  22.  
  23. Install the air outlet trim plates and climate control system switch panel.
  24.  
  25. Install the radio and speakers.
  26.  
  27. Reverse the removal procedure to install the instrument panel pad.
  28.  
  29. Connect the negative battery cable and check all items in the instrument panel for proper operation.
  30.  

1995-96 MODELS
See Figure 1


Click image to see an enlarged view

Fig. Fig. 1: Exploded view of the instrument panel assembly - 1994 Grand Prix and 1995-96 Regal and Cutlass Supreme


CAUTION
Properly disarm the air bag on vehicles equipped with the Supplemental Restraint System (SRS). Failure to do so can cause serious injury.

  1. Disconnect the front door inside carpet retainers.
  2.  
  3. Remove the sound insulators.
  4.  
  5. Disable the air bag system as outlined in Chassis Electrical .
  6.  
  7. Remove the windshield side upper garnish mouldings.
  8.  
  9. Remove the instrument panel upper trim panel as follows:
    1. Insert a flat bladed tool, downward at the rearmost edge of the upper trim panel.
    2.  
    3. Carefully pry the panel up to release the 10 panel tabs.
    4.  
    5. Lift the rear edge approximately 2 inches and pull the panel rearward to remove.
    6.  

  10.  
  11. Remove the instrument panel lower compartment.
  12.  
  13. Disconnect the theft deterrent module.
  14.  
  15. Disconnect the passenger side air bag inflator module.
  16.  
  17. Remove the steering column opening filler.
  18.  
  19. Remove the instrument panel cluster trim plate.
  20.  
  21. Remove the console, if equipped.
  22.  
  23. Remove the audio system as outlined in Chassis Electrical .
  24.  
  25. Remove the ventilation control system.
  26.  
  27. Remove the instrument panel cluster.
  28.  
  29. Disconnect the headlamp switch, foglamp, HUD switch and trip calculator, if equipped.
  30.  
  31. Disconnect the fuse block.
  32.  
  33. Remove the knee bolster deflector.
  34.  
  35. Remove the steering column nuts and lower the steering column.
  36.  
  37. Remove the instrument panel carrier mounting bolts and screws.
  38.  
  39. Disconnect the data link connector, lower compartment light and trunk release switch.
  40.  
  41. Remove the instrument panel carrier clips.
  42.  
  43. Reposition the instrument panel wiring harness and remove the carrier assembly.
  44.  

To install:
  1. Reposition the instrument panel carrier assembly and route the instrument panel wiring.
  2.  
  3. Install the instrument panel carrier clips.
  4.  
  5. Connect the data link connector, lower compartment light and trunk release switch.
  6.  
  7. Install the instrument panel carrier mounting bolts and screws and tighten the bolts to 89 inch lbs. (10 Nm).
  8.  
  9. Raise the steering column and install the retaining nuts.
  10.  
  11. Install the knee bolster deflector.
  12.  
  13. Connect the fuse block.
  14.  
  15. Connect the headlamp switch, foglamp, HUD switch and trip calculator, if equipped.
  16.  
  17. Install the instrument panel cluster.
  18.  
  19. Install the audio system as outlined in Chassis Electrical .
  20.  
  21. Install the instrument panel cluster.
  22.  
  23. Install the instrument panel cluster trim plate.
  24.  
  25. Install the console, if equipped.
  26.  
  27. Install the steering column opening filler.
  28.  
  29. Connect the passenger side air bag inflator module.
  30.  
  31. Connect the theft deterrent module.
  32.  
  33. Install the instrument panel lower compartment.
  34.  
  35. Install the instrument panel upper trim panel.
  36.  
  37. Install the windshield side upper garnish mouldings.
  38.  
  39. Enable the air bag system as outlined in Chassis Electrical .
  40.  
  41. Install the sound insulators.
  42.  
  43. Connect the front door inside carpet retainers.
  44.  

Grand Prix
1988-93 MODELS
See Figure 2


Click image to see an enlarged view

Fig. Fig. 2: Exploded view of the instrument panel assembly - 1998-93 Grand Prix

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the instrument panel pad:
    1. Remove the 2 screws at the top of the instrument panel trim plate.
    2.  
    3. Remove the glove box and the screw above it.
    4.  
    5. Lift the front of the pad and pull toward you to release the clips.
    6.  
    7. Disconnect the speaker connectors and Daytime Running Lights connector, and remove the pad.
    8.  

  4.  
  5. Remove the lights switches assembly and wiper/washer switch assembly.
  6.  
  7. Remove the instrument cluster trim plate.
  8.  
  9. Remove the parking brake release handle and allow it to dangle below.
  10.  
  11. Remove the ALDL connector and allow it to dangle below the instrument panel.
  12.  
  13. Remove the left and right side sound insulators.
  14.  
  15. Remove the steering column trim plate.
  16.  
  17. Lower the steering column.
  18.  
  19. Remove the screws fastening the fuse block and position the fuse block aside.
  20.  
  21. Disconnect the HVAC connector and remove the remote radio amplifier.
  22.  
  23. Remove the radio controls trim cover and climate control switch panel trim cover. Then remove the radio and climate control switch panel.
  24.  
  25. Remove the ashtray and cassette deck or compartment that replaces it if not equipped. Remove the remote radio receiver.
  26.  
  27. Remove the instrument cluster.
  28.  
  29. Remove both speakers.
  30.  
  31. Remove 7 screws holding ventilation duct to instrument panel.
  32.  
  33. Remove 3 nuts holding wiring harness carrier.
  34.  
  35. Have a helper assist you, and remove the instrument panel assembly from the vehicle.
  36.  

To install:
  1. Carefully install the instrument panel to the vehicle. Be sure to clear all wiring, etc.
  2.  
  3. Install the nuts holding wiring harness carrier.
  4.  
  5. Install the screws holding ventilation duct to instrument panel.
  6.  
  7. Install the speakers and instrument cluster. Install the remote radio receiver.
  8.  
  9. Install the ashtray and cassette deck or compartment.
  10.  
  11. Install the radio and climate control switch panel and trim covers.
  12.  
  13. Install the remote radio amplifier and connect the HVAC connector.
  14.  
  15. Secure the fuse block.
  16.  
  17. Secure the steering column and install the trim plate.
  18.  
  19. Install the left and right side sound insulators.
  20.  
  21. Install the ALDL connector.
  22.  
  23. Secure the parking brake release handle.
  24.  
  25. Install the instrument cluster trim plate.
  26.  
  27. Install the lights switches assembly and wiper/washer switch assembly.
  28.  
  29. Reverse the removal procedure to install the instrument panel pad.
  30.  
  31. Connect the negative battery cable and check all items in the instrument panel for proper operation.
  32.  

1994-96 MODELS
See Figure 1

CAUTION
Properly disarm the air bag on vehicles equipped with the Supplemental Restraint System (SRS). Failure to do so can cause serious injury.

  1. Disconnect the front door inside carpet retainers.
  2.  
  3. Remove the sound insulators.
  4.  
  5. Disable the air bag system as outlined in Chassis Electrical .
  6.  
  7. Remove the windshield side upper garnish mouldings.
  8.  
  9. Remove the instrument panel upper trim panel as follows:
    1. Insert a flat bladed tool, downward at the rearmost edge of the upper trim panel.
    2.  
    3. Carefully pry the panel up to release the 10 panel tabs.
    4.  
    5. Lift the rear edge approximately 2 inches and pull the panel rearward to remove.
    6.  

  10.  
  11. Remove the instrument panel lower compartment.
  12.  
  13. Disconnect the theft deterrent module.
  14.  
  15. Disconnect the passenger side air bag inflator module.
  16.  
  17. Remove the steering column opening filler.
  18.  
  19. Remove the instrument panel cluster trim plate.
  20.  
  21. Remove the console, if equipped.
  22.  
  23. Remove the audio system as outlined in Chassis Electrical .
  24.  
  25. Remove the ventilation control system.
  26.  
  27. Remove the instrument panel cluster.
  28.  
  29. Disconnect the headlamp switch, foglamp, HUD switch and trip calculator, if equipped.
  30.  
  31. Disconnect the fuse block.
  32.  
  33. Remove the knee bolster deflector.
  34.  
  35. Remove the steering column nuts and lower the steering column.
  36.  
  37. Remove the instrument panel carrier mounting bolts and screws.
  38.  
  39. Disconnect the data link connector, lower compartment light and trunk release switch.
  40.  
  41. Remove the instrument panel carrier clips.
  42.  
  43. Reposition the instrument panel wiring harness and remove the carrier assembly.
  44.  

To install:
  1. Reposition the instrument panel carrier assembly and route the instrument panel wiring.
  2.  
  3. Install the instrument panel carrier clips.
  4.  
  5. Connect the data link connector, lower compartment light and trunk release switch.
  6.  
  7. Install the instrument panel carrier mounting bolts and screws and tighten the bolts to 89 inch lbs. (10 Nm).
  8.  
  9. Raise the steering column and install the retaining nuts.
  10.  
  11. Install the knee bolster deflector.
  12.  
  13. Connect the fuse block.
  14.  
  15. Connect the headlamp switch, foglamp, HUD switch and trip calculator, if equipped.
  16.  
  17. Install the instrument panel cluster.
  18.  
  19. Install the audio system as outlined in Chassis Electrical .
  20.  
  21. Install the instrument panel cluster.
  22.  
  23. Install the instrument panel cluster trim plate.
  24.  
  25. Install the console, if equipped.
  26.  
  27. Install the steering column opening filler.
  28.  
  29. Connect the passenger side air bag inflator module.
  30.  
  31. Connect the theft deterrent module.
  32.  
  33. Install the instrument panel lower compartment.
  34.  
  35. Install the instrument panel upper trim panel.
  36.  
  37. Install the windshield side upper garnish mouldings.
  38.  
  39. Enable the air bag system as outlined in Chassis Electrical .
  40.  
  41. Install the sound insulators.
  42.  
  43. Connect the front door inside carpet retainers.
  44.  

Lumina and Monte
1990-94 MODELS
See Figure 3


Click image to see an enlarged view

Fig. Fig. 3: Exploded view of the instrument panel assembly - 1990-94 Lumina

  1. Disconnect the negative battery cable.
  2.  
  3. Disconnect the Daytime Running Lamp sensor if equipped.
  4.  
  5. Remove the screws under the edge of the instrument panel pad, and remove the pad by pulling up to release and out.
  6.  
  7. Remove the speakers.
  8.  
  9. Remove the instrument cluster.
  10.  
  11. Remove the glovebox.
  12.  
  13. Remove the right side sound insulator.
  14.  
  15. Remove the climate control system switch panel.
  16.  
  17. Remove the radio.
  18.  
  19. Remove the lamps switches.
  20.  
  21. Remove the ashtray and bracket.
  22.  
  23. Remove the ALDL connector and allow it to dangle below the instrument panel.
  24.  
  25. Remove the parking brake release handle and allow it to dangle below.
  26.  
  27. Remove the screws fastening the fuse block and position the fuse block aside.
  28.  
  29. Remove the steering column trim plate and lower the steering column.
  30.  
  31. Remove 7 bolts holding the carrier (5 at the top and 2 at the bottom).
  32.  
  33. Remove the 5 screws holding the main air duct.
  34.  
  35. Disengage 9 clips holding the wiring harness.
  36.  
  37. Have a helper assist you, and remove the instrument panel assembly from the vehicle.
  38.  

To install:
  1. Carefully install the instrument panel to the vehicle. Be sure to clear all wiring, etc.
  2.  
  3. Engage the clips holding the wiring harness.
  4.  
  5. Install the 5 screws holding the main air duct.
  6.  
  7. Install the bolts holding the carrier.
  8.  
  9. Secure the steering column and install the trim plate.
  10.  
  11. Secure the fuse block, parking brake release handle and ALDL connector.
  12.  
  13. Install the ashtray and bracket.
  14.  
  15. Install the lamps switches.
  16.  
  17. Install the radio.
  18.  
  19. Install the climate control system switch panel.
  20.  
  21. Install the right side sound insulator and glovebox.
  22.  
  23. Install the instrument cluster.
  24.  
  25. Install the speakers.
  26.  
  27. Install the instrument panel pad and screws.
  28.  
  29. Connect the Daytime Running Lamp sensor if equipped.
  30.  
  31. Connect the negative battery cable and check all items in the instrument panel for proper operation.
  32.  

1995-96 MODELS
See Figure 4


Click image to see an enlarged view

Fig. Fig. 4: Exploded view of the instrument panel assembly - 1995-96 Lumina and Monte Carlo


CAUTION
Properly disarm the air bag on vehicles equipped with the Supplemental Restraint System (SRS). Failure to do so can cause serious injury.

  1. Disconnect the front door inside carpet retainers.
  2.  
  3. Remove the sound insulators.
  4.  
  5. Disable the air bag system as outlined in Chassis Electrical .
  6.  
  7. Remove the windshield side upper garnish mouldings.
  8.  
  9. Remove the instrument panel upper trim panel as follows:
    1. Insert a flat bladed tool, downward at the rearmost edge of the upper trim panel.
    2.  
    3. Carefully pry the panel up to release the 10 panel tabs.
    4.  
    5. Lift the rear edge approximately 2 in. (50.8mm) and pull the panel rearward to remove.
    6.  

  10.  
  11. Remove the instrument panel lower compartment.
  12.  
  13. Disconnect the theft deterrent module.
  14.  
  15. Disconnect the passenger side air bag inflator module.
  16.  
  17. Remove the steering column opening filler.
  18.  
  19. Remove the instrument panel cluster trim plate.
  20.  
  21. Remove the console, if equipped.
  22.  
  23. Remove the audio system as outlined in Chassis Electrical .
  24.  
  25. Remove the ventilation control system.
  26.  
  27. Remove the instrument panel cluster.
  28.  
  29. Disconnect the headlamp switch.
  30.  
  31. Disconnect the fuse block.
  32.  
  33. Remove the knee bolster deflector.
  34.  
  35. Remove the steering column nuts and lower the steering column.
  36.  
  37. Remove the instrument panel carrier mounting bolts and screws.
  38.  
  39. Disconnect the data link connector, lower compartment light and trunk release switch.
  40.  
  41. Remove the instrument panel carrier clips.
  42.  
  43. Reposition the instrument panel wiring harness and remove the carrier assembly.
  44.  

To install:
  1. Reposition the instrument panel carrier assembly and route the instrument panel wiring.
  2.  
  3. Install the instrument panel carrier clips.
  4.  
  5. Connect the data link connector, lower compartment light and trunk release switch.
  6.  
  7. Install the instrument panel carrier mounting bolts and screws and tighten the bolts to 89 inch lbs. (10 Nm).
  8.  
  9. Raise the steering column and install the retaining nuts.
  10.  
  11. Install the knee bolster deflector.
  12.  
  13. Connect the fuse block.
  14.  
  15. Connect the headlamp switch.
  16.  
  17. Install the instrument panel cluster.
  18.  
  19. Install the audio system as outlined in Chassis Electrical .
  20.  
  21. Install the instrument panel cluster.
  22.  
  23. Install the instrument panel cluster trim plate.
  24.  
  25. Install the console, if equipped.
  26.  
  27. Install the steering column opening filler.
  28.  
  29. Connect the passenger side air bag inflator module.
  30.  
  31. Connect the theft deterrent module.
  32.  
  33. Install the instrument panel lower compartment.
  34.  
  35. Install the instrument panel upper trim panel.
  36.  
  37. Install the windshield side upper garnish mouldings.
  38.  
  39. Enable the air bag system as outlined in Chassis Electrical .
  40.  
  41. Install the sound insulators.
  42.  
  43. Connect the front door inside carpet retainers.
  44.  

Regal
1988-94 MODELS
See Figure 5


Click image to see an enlarged view

Fig. Fig. 5: Exploded view of the instrument panel assembly-1994 Regal

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the instrument panel pad:
    1. Carefully pry the speaker grilles and disconnect the Daytime Running Lamp sensor if equipped.
    2.  
    3. Remove the screw under each speaker grille.
    4.  
    5. Remove the screws at the lower edge of the instrument panel pad.
    6.  
    7. Remove the pad by lifting the front and pulling toward you to release it.
    8.  

  4.  
  5. Remove the speakers
  6.  
  7. Remove the instrument cluster.
  8.  
  9. Remove the glovebox.
  10.  
  11. Remove the right side sound insulator.
  12.  
  13. Remove the climate control system switch panel and sound system controls.
  14.  
  15. Remove the English/Metric switch.
  16.  
  17. Remove the lights switches.
  18.  
  19. Remove the cassette deck or compartment that replaces it if not equipped. Remove the ashtray and bracket.
  20.  
  21. Remove the ALDL connector and allow it to dangle below the instrument panel.
  22.  
  23. Remove the parking brake release handle and allow it to dangle below.
  24.  
  25. Remove the remote radio receiver.
  26.  
  27. Remove the steering column trim plate and lower the steering column.
  28.  
  29. Remove 7 bolts holding the carrier (5 at the top and 2 at the bottom). Remove the 2 bolts above the steering column.
  30.  
  31. Remove the 5 screws holding the main air duct.
  32.  
  33. Remove the 3 nuts holding the conduit. Two are above the glovebox and the other is through the cassette/compartment opening.
  34.  
  35. Disengage 9 clips holding the wiring harness.
  36.  
  37. Have a helper assist you, and remove the instrument panel assembly from the vehicle.
  38.  

To install:
  1. Carefully install the instrument panel to the vehicle. Be sure to clear all wiring, etc.
  2.  
  3. Engage the clips holding the wiring harness.
  4.  
  5. Install the 3 nuts holding the conduit.
  6.  
  7. Install the screws holding the main air duct.
  8.  
  9. Install the bolts holding the carrier.
  10.  
  11. Secure the steering column and install the trim plate.
  12.  
  13. Install the remote radio receiver.
  14.  
  15. Secure the fuse block, parking brake release handle and ALDL connector.
  16.  
  17. Install the ashtray and bracket.
  18.  
  19. Install the cassette deck or compartment.
  20.  
  21. Install the lights switches and English/Metric switch.
  22.  
  23. Install the climate control system switch panel and sound system controls.
  24.  
  25. Install the right side sound insulator and glovebox.
  26.  
  27. Install the instrument cluster and speakers.
  28.  
  29. Reverse the removal procedure to install the instrument panel pad.
  30.  
  31. Connect the negative battery cable and check all items in the instrument panel for proper operation.
  32.  

1995-96 MODELS
See Figure 1

CAUTION
Properly disarm the air bag on vehicles equipped with the Supplemental Restraint System (SRS). Failure to do so can cause serious injury.

  1. Disconnect the front door inside carpet retainers.
  2.  
  3. Remove the sound insulators.
  4.  
  5. Disable the air bag system as outlined in Chassis Electrical .
  6.  
  7. Remove the windshield side upper garnish mouldings.
  8.  
  9. Remove the instrument panel upper trim panel as follows:
    1. Insert a flat bladed tool, downward at the rearmost edge of the upper trim panel.
    2.  
    3. Carefully pry the panel up to release the 10 panel tabs.
    4.  
    5. Lift the rear edge approximately 2 in. (50.8mm) and pull the panel rearward to remove.
    6.  

  10.  
  11. Remove the instrument panel lower compartment.
  12.  
  13. Disconnect the theft deterrent module.
  14.  
  15. Disconnect the passenger side air bag inflator module.
  16.  
  17. Remove the steering column opening filler.
  18.  
  19. Remove the instrument panel cluster trim plate.
  20.  
  21. Remove the console, if equipped.
  22.  
  23. Remove the audio system as outlined in Chassis Electrical .
  24.  
  25. Remove the ventilation control system.
  26.  
  27. Remove the instrument panel cluster.
  28.  
  29. Disconnect the headlamp switch, foglamp, HUD switch and trip calculator, if equipped.
  30.  
  31. Disconnect the fuse block.
  32.  
  33. Remove the knee bolster deflector.
  34.  
  35. Remove the steering column nuts and lower the steering column.
  36.  
  37. Remove the instrument panel carrier mounting bolts and screws.
  38.  
  39. Disconnect the data link connector, lower compartment light and trunk release switch.
  40.  
  41. Remove the instrument panel carrier clips.
  42.  
  43. Reposition the instrument panel wiring harness and remove the carrier assembly.
  44.  

To install:
  1. Reposition the instrument panel carrier assembly and route the instrument panel wiring.
  2.  
  3. Install the instrument panel carrier clips.
  4.  
  5. Connect the data link connector, lower compartment light and trunk release switch.
  6.  
  7. Install the instrument panel carrier mounting bolts and screws and tighten the bolts to 89 inch lbs. (10 Nm).
  8.  
  9. Raise the steering column and install the retaining nuts.
  10.  
  11. Install the knee bolster deflector.
  12.  
  13. Connect the fuse block.
  14.  
  15. Connect the headlamp switch, foglamp, HUD switch and trip calculator, if equipped.
  16.  
  17. Install the instrument panel cluster.
  18.  
  19. Install the audio system as outlined in Chassis Electrical .
  20.  
  21. Install the instrument panel cluster.
  22.  
  23. Install the instrument panel cluster trim plate.
  24.  
  25. Install the console, if equipped.
  26.  
  27. Install the steering column opening filler.
  28.  
  29. Connect the passenger side air bag inflator module.
  30.  
  31. Connect the theft deterrent module.
  32.  
  33. Install the instrument panel lower compartment.
  34.  
  35. Install the instrument panel upper trim panel.
  36.  
  37. Install the windshield side upper garnish mouldings.
  38.  
  39. Enable the air bag system as outlined in Chassis Electrical .
  40.  
  41. Install the sound insulators.
  42.  
  43. Connect the front door inside carpet retainers.
  44.  

 
label.common.footer.alt.autozoneLogo