GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide

Fuel and Oil Recommendations

Print

OIL



See Figures 1 and 2



Click image to see an enlarged view

Fig. Fig. 1: Recommended SAE engine oil viscosity grades



Click image to see an enlarged view

Fig. Fig. 2: Look for the API oil identification label when choosing your engine oil

The Society of Automotive Engineers (SAE) grade number indicates the viscosity of the engine oil; its resistance to flow at a given temperature. The lower the SAE grade number, the lighter the oil. For example, the mono-grade oils begin with SAE 5 weight, which is a thin light oil, and continue in viscosity up to SAE 80 or 90 weight, which are heavy gear lubricants. These oils are also known as "straight weight", meaning they are of a single viscosity, and do not vary with engine temperature.

Multi-viscosity oils offer the important advantage of being adaptable to temperature extremes. These oils have designations such as 10W-40, 20W-50, etc. The 10W-40 means that in winter (the "W'' in the designation) the oil acts like a thin 10 weight oil, allowing the engine to spin easily when cold and offering rapid lubrication. Once the engine has warmed up, however, the oil acts like a straight 40 weight, maintaining good lubrication and protection for the engine's internal components. A 20W-50 oil would therefore be slightly heavier than and not as ideal in cold weather as the 10W-40, but would offer better protection at higher rpm and temperatures because when warm it acts like a 50 weight oil. Whichever oil viscosity you choose when changing the oil, make sure you are anticipating the temperatures your engine will be operating in until the oil is changed again. Refer to the oil viscosity chart for oil recommendations according to temperature.

The American Petroleum Institute (API) designation indicates the classification of engine oil used under certain given operating conditions. Only oils designated for use "Service SG'' or greater should be used. Oils of the SG type perform a variety of functions inside the engine in addition to the basic function as a lubricant. Through a balanced system of metallic detergents and polymeric dispersants, the oil prevents the formation of high and low temperature deposits and also keeps sludge and particles of dirt in suspension. Acids, particularly sulfuric acid, as well as other by-products of combustion, are neutralized. Both the SAE grade number and the APE designation can be found on top of the oil can.

For recommended oil viscosity's, refer to the chart. Note that 10W-30 and 10W-40 grade oils are not recommended for sustained high speed driving when the temperature rises above the indicated limit.

Synthetic Oil

There are many excellent synthetic and fuel-efficient oils currently available that can provide better gas mileage, longer service life and, in some cases, better engine protection. These benefits do not come without a few hitches, however; the main one being the price of synthetic oils, which may be more expensive than the price per quart of conventional oil.

Synthetic oil is not for every car and every type of driving, so you should consider your engine's condition and your type of driving. Also, check your car's warranty conditions regarding the use of synthetic oils.

FUEL



It is important to use fuel of the proper octane rating in your vehicle. Octane rating is based on the quantity of anti-knock compounds added to the fuel and it determines the speed at which the gas will burn. The lower the octane rating, the faster it burns. The higher the octane, the slower the fuel will burn and a greater percentage of compounds in the fuel prevent spark ping (knock), detonation and preignition (dieseling).

As the temperature of the engine increases, the air/fuel mixture exhibits a tendency to ignite before the spark plug is fired. If fuel of an octane rating too low for the engine is used, this will allow combustion to occur before the piston has completed its compression stroke, thereby creating a very high pressure very rapidly.

Fuel of the proper octane rating, for the compression ratio and ignition timing of your truck, will slow the combustion process sufficiently to allow the spark plug enough time to ignite the mixture completely and smoothly. Many non-catalyst models are designed to run on regular fuel. The use of some super-premium fuel is no substitution for a properly tuned and maintained engine. Chances are that if your engine exhibits any signs of spark ping, detonation or pre-ignition when using regular fuel, the ignition timing should be checked against specifications or the cylinder head should be removed for decarbonizing.

Most models are designed to operate using unleaded gasoline with a minimum rating of 87 octane. Use of unleaded gas with octane ratings lower than 87 can cause persistent spark knock which could lead to engine damage.

Light spark knock may be noticed when accelerating or driving up hills. The slight knocking may be considered normal (with 87 octane) because the maximum fuel economy is obtained under condition of occasional light spark knock. Gasoline with an octane rating higher than 87 may be used, but it is not necessary (in most cases) for proper operation.

If spark knock is constant, when using 87 octane, at cruising speeds on level ground, ignition timing adjustment may be required. Refer to this section for the proper procedure

Your engine's fuel requirement can change with time, mainly due to carbon buildup, which changes the compression ratio. If your engine pings, knocks or runs on, switch to a higher grade of fuel. Sometimes just changing brands will cure the problem. If it becomes necessary to retard the timing from specifications, don't change it more than a few degrees. Retarded timing will reduce power output and fuel mileage and will increase the engine temperature.

 
label.common.footer.alt.autozoneLogo