Jumper wires are simple, yet extremely valuable, pieces of test equipment. Jumper wires are merely wires that are used to bypass sections of a circuit. The simplest type of jumper wire is merely a length of multi-strand wire with an alligator clip at each end. Jumper wires are usually fabricated from lengths of standard automotive wire and whatever type of connector (alligator clip, spade connector or pin connector) that is required for the particular vehicle being tested. The well equipped tool box will have several different styles of jumper wires in several different lengths. Some jumper wires are made with three or more terminals coming from a common splice for special purpose testing. In cramped, hard-to-reach areas it is advisable to have insulated boots over the jumper wire terminals in order to prevent accidental grounding, sparks, and possible fire, especially when testing fuel system components.
Jumper wires are used primarily to locate open electrical circuits, on either the ground (-) side of the circuit or on the hot (+) side. If an electrical component fails to operate, connect the jumper wire between the component and a good ground. If the component operates only with the jumper installed, the ground circuit is open. If the ground circuit is good, but the component does not operate, the circuit between the power feed and component is open. You can sometimes connect the jumper wire directly from the battery to the hot terminal of the component, but first make sure the component uses 12 volts in operation. Some electrical components, such as fuel injectors, are designed to operate on about 4 volts and running 12 volts directly to the injector terminals can burn out the wiring. By inserting an inline fuse holder between a set of test leads, a fused jumper wire can be used for bypassing open circuits. Use a 5 amp fuse to provide protection against voltage spikes. When in doubt, use a voltmeter to check the voltage input to the component and measure how much voltage is being applied normally. By moving the jumper wire successively back from the lamp toward the power source, you can isolate the area of the circuit where the open is located. When the component stops functioning, or the power is cut off, the open is in the segment of wire between the jumper and the point previously tested.
12 VOLT TEST LIGHT
The 12 volt test light is used to check circuits and components while electrical current is flowing through them. It is used for voltage and ground tests. Twelve volt test lights come in different styles but all have three main parts; a ground clip, a probe, and a light. The most commonly used 12 volt test lights have pick-type probes. To use a 12 volt test light, connect the ground clip to a good ground and probe wherever necessary with the pick. The pick should be sharp so that it can penetrate wire insulation to make contact with the wire, without making a large hole in the insulation. The wrap-around light is handy in hard to reach areas or where it is difficult to support a wire to push a probe pick into it. To use the wrap around light, hook the wire to probed with the hook and pull the trigger. A small pick will be forced through the wire insulation into the wire core.
Like the jumper wire, the 12 volt test light is used to isolate opens in circuits. But, whereas the jumper wire is used to bypass the open to operate the load, the 12 volt test light is used to locate the presence of voltage in a circuit. If the test light glows, you know that there is power up to that point; if the 12 volt test light does not glow when its probe is inserted into the wire or connector, you know that there is an open circuit (no power). Move the test light in successive steps back toward the power source until the light in the handle does glow. When it does glow, the open is between the probe and point previously probed.
The test light does not detect that 12 volts (or any particular amount of voltage) is present; it only detects that some voltage is present. It is advisable before using the test light to touch its terminals across the battery posts to make sure the light is operating properly.
SELF-POWERED TEST LIGHT
The self-powered test light usually contains a 1.5 volt penlight battery. One type of self-powered test light is similar in design to the 12 volt test light. This type has both the battery and the light in the handle and pick-type probe tip. The second type has the light toward the open tip, so that the light illuminates the contact point. The self-powered test light is dual purpose piece of test equipment. It can be used to test for either open or short circuits when power is isolated from the circuit (continuity test). A powered test light should not be used on any computer controlled system or component unless specifically instructed to do so. Many engine sensors can be destroyed by even this small amount of voltage applied directly to the terminals.Open Circuit Testing
To use the self-powered test light to check for open circuits, first isolate the circuit from the vehicle's 12 volt power source by disconnecting the battery or wiring harness connector. Connect the test light ground clip to a good ground and probe sections of the circuit sequentially with the test light. (start from either end of the circuit). If the light is out, the open is between the probe and the circuit ground. If the light is on, the open is between the probe and end of the circuit toward the power source.Short Circuit Testing
By isolating the circuit both from power and from ground, and using a self-powered test light, you can check for shorts to ground in the circuit. Isolate the circuit from power and ground. Connect the test light ground clip to a good ground and probe any easy-to-reach test point in the circuit. If the light comes on, there is a short somewhere in the circuit. To isolate the short, probe a test point at either end of the isolated circuit (the light should be on). Leave the test light probe connected and open connectors, switches, remove parts, etc., sequentially, until the light goes out. When the light goes out, the short is between the last circuit component opened and the previous circuit opened.
The 1.5 volt battery in the test light does not provide much current. A weak battery may not provide enough power to illuminate the test light even when a complete circuit is made (especially if there are high resistances in the circuit). Always make sure that the test battery is strong. To check the battery, briefly touch the ground clip to the probe; if the light glows brightly the battery is strong enough for testing. Never use a self-powered test light to perform checks for opens or shorts when power is applied to the electrical system under test. The 12 volt vehicle power will quickly burn out the 1.5 volt light bulb in the test light.
A voltmeter is used to measure voltage at any point in a circuit, or to measure the voltage drop across any part of a circuit. It can also be used to check continuity in a wire or circuit by indicating current flow from one end to the other. Voltmeters usually have various scales on the meter dial and a selector switch to allow the selection of different voltages. The voltmeter has a positive and a negative lead. To avoid damage to the meter, always connect the negative lead to the negative (-) side of circuit (to ground or nearest the ground side of the circuit) and connect the positive lead to the positive (+) side of the circuit (to the power source or the nearest power source). Note that the negative voltmeter lead will always be black and that the positive voltmeter will always be some color other than black (usually red). Depending on how the voltmeter is connected into the circuit, it has several uses.
A voltmeter can be connected either in parallel or in series with a circuit and it has a very high resistance to current flow. When connected in parallel, only a small amount of current will flow through the voltmeter current path; the rest will flow through the normal circuit current path and the circuit will work normally. When the voltmeter is connected in series with a circuit, only a small amount of current can flow through the circuit. The circuit will not work properly, but the voltmeter reading will show if the circuit is complete or not.Available Voltage Measurement
Set the voltmeter selector switch to the 20V position and connect the meter negative lead to the negative post of the battery. Connect the positive meter lead to the positive post of the battery and turn the ignition switch ON to provide a load. Read the voltage on the meter or digital display. A well charged battery should register over 12 volts. If the meter reads below 11.5 volts, the battery power may be insufficient to operate the electrical system properly. This test determines voltage available from the battery and should be the first step in any electrical trouble diagnosis procedure. Many electrical problems, especially on computer controlled systems, can be caused by a low state of charge in the battery. Excessive corrosion at the battery cable terminals can cause a poor contact that will prevent proper charging and full battery current flow.
Normal battery voltage is 12 volts when fully charged. When the battery is supplying current to one or more circuits it is said to be "under load". When everything is off the electrical system is under a "no-load" condition. A fully charged battery may show about 12.5 volts at no load; will drop to 12 volts under medium load; and will drop even lower under heavy load. If the battery is partially discharged the voltage decrease under heavy load may be excessive, even though the battery shows 12 volts or more at no load. When allowed to discharge further, the battery's available voltage under load will decrease more severely. For this reason, it is important that the battery be fully charged during all testing procedures to avoid errors in diagnosis and incorrect test results.Voltage Drop
When current flows through a resistance, the voltage beyond the resistance is reduced (the larger the current, the greater the reduction in voltage). When no current is flowing, there is no voltage drop because there is no current flow. All points in the circuit which are connected to the power source are at the same voltage as the power source. The total voltage drop always equals the total source voltage. In a long circuit with many connectors, a series of small, unwanted voltage drops due to corrosion at the connectors can add up to a total loss of voltage which impairs the operation of the normal loads in the circuit.Indirect Computation of Voltage Drops
- Set the voltmeter selector switch to the 20 volt position.
- Connect the meter negative lead to a good ground.
- Probe all resistances in the circuit with the positive meter lead.
- Operate the circuit in all modes and observe the voltage readings.
- Set the voltmeter switch to the 20 volt position.
- Connect the voltmeter negative lead to the ground side of the resistance load to be measured.
- Connect the positive lead to the positive side of the resistance or load to be measured.
- Read the voltage drop directly on the 20 volt scale.
Too high a voltage indicates too high a resistance. If, for example, a blower motor runs too slowly, you can determine if there is too high a resistance in the resistor pack. By taking voltage drop readings in all parts of the circuit, you can isolate the problem. Too low a voltage drop indicates too low a resistance. If, for example, a blower motor runs too fast in the MED and/or LOW position, the problem can be isolated in the resistor pack by taking voltage drop readings in all parts of the circuit to locate a possibly shorted resistor. The maximum allowable voltage drop under load is critical, especially if there is more than one high resistance problem in a circuit because all voltage drops are cumulative. A small drop is normal due to the resistance of the conductors.High Resistance Testing
- Set the voltmeter selector switch to the 4 volt position.
- Connect the voltmeter positive lead to the positive post of the battery.
- Turn on the headlights and heater blower to provide a load.
- Probe various points in the circuit with the negative voltmeter lead.
- Read the voltage drop on the 4 volt scale. Some average maximum allowable voltage drops are:
Voltage drops are all measured while a load is operating; without current flow, there will be no voltage drop.
The ohmmeter is designed to read resistance (ohms) in a circuit or component. Although there are several different styles of ohmmeters, all will usually have a selector switch which permits the measurement of different ranges of resistance (usually the selector switch allows the multiplication of the meter reading by 10, 100, 1000, and 10,000). A calibration knob allows the meter to be set at zero for accurate measurement. Since all ohmmeters are powered by an internal battery (usually 9 volts), the ohmmeter can be used as a self-powered test light. When the ohmmeter is connected, current from the ohmmeter flows through the circuit or component being tested. Since the ohmmeter's internal resistance and voltage are known values, the amount of current flow through the meter depends on the resistance of the circuit or component being tested.
The ohmmeter can be used to perform continuity test for opens or shorts (either by observation of the meter needle or as a self-powered test light), and to read actual resistance in a circuit. It should be noted that the ohmmeter is used to check the resistance of a component or wire while there is no voltage applied to the circuit. Current flow from an outside voltage source (such as the vehicle battery) can damage the ohmmeter, so the circuit or component should be isolated from the vehicle electrical system before any testing is done. Since the ohmmeter uses its own voltage source, either lead can be connected to any test point.
When checking diodes or other solid state components, the ohmmeter leads can only be connected one way in order to measure current flow in a single direction. Make sure the positive (+) and negative (-) terminal connections are as described in the test procedures to verify the one-way diode operation.
In using the meter for making continuity checks, do not be concerned with the actual resistance readings. Zero resistance, or any resistance readings, indicate continuity in the circuit. Infinite resistance indicates an open in the circuit. A high resistance reading where there should be none indicates a problem in the circuit. Checks for short circuits are made in the same manner as checks for open circuits except that the circuit must be isolated from both power and normal ground. Infinite resistance indicates no continuity to ground, while zero resistance indicates a dead short to ground.Resistance Measurement
The batteries in an ohmmeter will weaken with age and temperature, so the ohmmeter must be calibrated or "zeroed" before taking measurements. To zero the meter, place the selector switch in its lowest range and touch the two ohmmeter leads together. Turn the calibration knob until the meter needle is exactly on zero.
All analog (needle) type ohmmeters must be zeroed before use, but some digital ohmmeter models are automatically calibrated when the switch is turned on. Self-calibrating digital ohmmeters do not have an adjusting knob, but its a good idea to check for a zero readout before use by touching the leads together. All computer controlled systems require the use of a digital ohmmeter with at least 10 megohms impedance for testing. Before any test procedures are attempted, make sure the ohmmeter used is compatible with the electrical system or damage to the on-board computer could result.
To measure resistance, first isolate the circuit from the vehicle power source by disconnecting the battery cables or the harness connector. Make sure the key is OFF when disconnecting any components or the battery. Where necessary, also isolate at least one side of the circuit to be checked to avoid reading parallel resistances. Parallel circuit resistances will always give a lower reading than the actual resistance of either of the branches. When measuring the resistance of parallel circuits, the total resistance will always be lower than the smallest resistance in the circuit. Connect the meter leads to both sides of the circuit (wire or component) and read the actual measured ohms on the meter scale. Make sure the selector switch is set to the proper ohm scale for the circuit being tested to avoid misreading the ohmmeter test value.
An ammeter measures the amount of current flowing through a circuit in units called amperes or amps. Amperes are units of electron flow which indicate how fast the electrons are flowing through the circuit. Since Ohms Law dictates that current flow in a circuit is equal to the circuit voltage divided by the total circuit resistance, increasing voltage also increases the current level (amps). Likewise, any decrease in resistance will increase the amount of amps in a circuit. At normal operating voltage, most circuits have a characteristic amount of amperes, called "current draw" which can be measured using an ammeter. By referring to a specified current draw rating, measuring the amperes, and comparing the two values, one can determine what is happening within the circuit to aid in diagnosis. An open circuit, for example, will not allow any current to flow so the ammeter reading will be zero. More current flows through a heavily loaded circuit or when the charging system is operating.
An ammeter is always connected in series with the circuit being tested. All of the current that normally flows through the circuit must also flow through the ammeter; if there is any other path for the current to follow, the ammeter reading will not be accurate. The ammeter itself has very little resistance to current flow and therefore will not affect the circuit, but it will measure current draw only when the circuit is closed and electricity is flowing. Excessive current draw can blow fuses and drain the battery, while a reduced current draw can cause motors to run slowly, lights to dim and other components to not operate properly. The ammeter can help diagnose these conditions by locating the cause of the high or low reading.
Different combinations of test meters can be built into a single unit designed for specific tests. Some of the more common combination test devices are known as Volt/Amp testers, Tach/Dwell meters, or Digital Multimeters. The Volt/Amp tester is used for charging system, starting system or battery tests and consists of a voltmeter, an ammeter and a variable resistance carbon pile. The voltmeter will usually have at least two ranges for use with 6, 12 and 24 volt systems. The ammeter also has more than one range for testing various levels of battery loads and starter current draw and the carbon pile can be adjusted to offer different amounts of resistance. The Volt/Amp tester has heavy leads to carry large amounts of current and many later models have an inductive ammeter pickup that clamps around the wire to simplify test connections. On some models, the ammeter also has a zero-center scale to allow testing of charging and starting systems without switching leads or polarity. A digital multimeter is a voltmeter, ammeter and ohmmeter combined in an instrument which gives a digital readout. These are often used when testing solid state circuits because of their high input impedance (usually 10 megohms or more).
The tach/dwell meter combines a tachometer and a dwell (cam angle) meter and is a specialized kind of voltmeter. The tachometer scale is marked to show engine speed in rpm and the dwell scale is marked to show degrees of distributor shaft rotation. In most electronic ignition systems, dwell is determined by the control unit, but the dwell meter can also be used to check the duty cycle (operation) of some electronic engine control systems. Some tach/dwell meters are powered by an internal battery, while others take their power from the car battery in use. The battery powered testers usually require calibration much like an ohmmeter before testing.