Grand Cherokee 2006-2007

Instrument Panel

Print

Removal & Installation



Instrument Panel
  1. Before servicing the vehicle, refer to the precautions section.
    CAUTION
    On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the negative battery (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death.

  2.  
  3. Remove the bolts and remove the driver-s side hush panel.
  4.  
  5. Using a trim stick, separate the upper clips and rotate the cover down and release the lower hinges at the bottom and remove the opening cover.
    CAUTION
    Before servicing the steering Column the airbag system must be disarmed. Failure to do so may result in accidental deployment of the airbag and possible personal injury.

  6.  
  7. Remove the three bolts in the lower shroud.
    NOTE
    Use care not to break off the tangs on the shrouds.

  8.  
  9. Then unsnap the lower shroud from the upper shroud.
  10.  
  11. Disconnect the steering column electrical connectors.
  12.  
  13. Remove the pinch bolt.
  14.  
  15. Remove the column support bolts.
  16.  
  17. Remove the column cross bolt and slide the column downward off the bracket and remove the steering column.
  18.  
  19. Remove the nuts attaching the instrument panel to the pedal support bracket.
  20.  
  21. Using a trim stick, remove the ignition cylinder bezel.
  22.  
  23. Remove the screws and remove the ignition cylinder
  24.  
  25. Disconnect the electrical connector.
  26.  
  27. Using a trim stick, remove the left side cover.
  28.  
  29. Remove the left side door sill trim.
  30.  
  31. Remove the driver-s side cowl trim panel.
  32.  
  33. Disconnect the electrical connectors.
  34.  
  35. Disconnect the electrical connectors.
  36.  
  37. Remove the bolts and disconnect the ground wires within the steering column opening to the left of the steering column.
  38.  
  39. Disconnect the white adjustable pedal electrical connector.
  40.  
  41. Remove the bolts and remove the left a-pillar trim.
  42.  
  43. Remove the two left side bolts and one screw at the a-pillar support.
  44.  
  45. Using a trim stick, remove the shifter bezel ring.
  46.  
  47. Using a trim stick, remove the shifter bezel.
  48.  
  49. Remove the center console back cover and disconnect the electrical connector.
  50.  
  51. Remove the screws and remove the console.
  52.  
  53. Disconnect the electrical connectors under the console.
  54.  
  55. Open the glove box and push the stop tabs down to drop the glove box out of the instrument panel.
  56.  
  57. Rotate the box down and release the door hinges at the bottom and remove the glove box.
  58.  
  59. Remove the passenger side hush panel.
  60.  
  61. Remove the right side door sill trim.
  62.  
  63. Remove the nut, separate the right cowl trim panel and remove.
  64.  
  65. Remove the right side end cap.
  66.  
  67. Disconnect the electrical connectors.
  68.  
  69. Remove the bolts and remove the right a-pillar trim panel.
  70.  
  71. Remove the two right side bolts and one screw at the a-pillar support.
  72.  
  73. Using a trim stick, remove the defroster grills.
  74.  
  75. Remove the two fence line nuts.
  76.  
  77. Using a trim stick, remove the radio bezel.
  78.  
  79. Using a trim stick, remove the center bezel and disconnect the electrical connectors.
  80.  
  81. Remove the nut from the HVAC support stud behind the center bezel.
  82.  
  83. Remove the screw to the HVAC from under the glove box opening.
  84.  
  85. Remove the HVAC bracket bolt from the glove box opening.
  86.  
  87. Remove the left and right center support brackets.
  88.  
  89. Remove the center floor duct.
  90.  
  91. Remove the radio.
  92.  
  93. Remove the two HVAC bolts from the radio opening.
  94.  
  95. Remove the instrument panel assembly.
  96.  

To install:

  1. Before proceeding with installation of the instrument panel assembly, remove the load clips from each a-pillar and install onto the sides of the panel using the screw.
  2.  
  3. Place the instrument panel into the vehicle and position onto the a-pillars using the load clips.
  4.  
  5. Install the two bolts on the right side and tighten the bolts to 95 inch lbs. (11 Nm).
  6.  
  7. Install the two fence line nuts.
  8.  
  9. Guide the peddle support studs on the driver-s side, into the slots in the instrument panel reinforcement.
  10.  
  11. Position the center stack brackets in front of the duct work.
  12.  
  13. Rotate the instrument panel back and guide the HVAC stud.
  14.  
  15. Continue to rotate the instrument panel back and guide the tube brackets located in the radio opening, into the HVAC.
  16.  
  17. Install the screw at the bottom of the column opening next to the center stack up from the bottom attaching the HVAC.
  18.  
  19. Install the bolt at the HVAC blower motor housing.
  20.  
  21. Install the screw at the bottom of the glove box opening to the blower motor housing support
  22.  
  23. Snap the lower glove box hinges over the pivots and rotate up.
  24.  
  25. Push the stop tabs down and close the glove box.
  26.  
  27. Connect the right side wiring.
  28.  
  29. Install the right hush panel trim.
  30.  
  31. Install the right cowl trim and position the door seal back.
  32.  
  33. Position the right side door sill trim and seat fully.
  34.  
  35. Install the right a-pillar trim, the bolts and position the door seal back.
  36.  
  37. Install the two bolts on the left side and tighten to 95 inch lbs. (11 Nm).
  38.  
  39. Position the right side end cap and seat fully.
  40.  
  41. Install the two nuts on the studs above the column tighten the nuts to 105 inch lbs. (12 Nm).
  42.  
  43. Connect the two left bulk connectors.
  44.  
  45. Connect the two fuse block connectors.
  46.  
  47. Connect the white connector to adjustable brake pedal.
  48.  
  49. Install the grounds within the steering column opening and install the bolts.
  50.  
  51. Install the left cowl trim panel and install the nut
  52.  
  53. Install the left door sill.
  54.  
  55. Install the column cross bolt and tighten to 105 inch lbs. (12 Nm).
  56.  
  57. Position the steering column shaft into the slip joint.
  58.  
  59. Lift the column into position and install the bolts.
  60.  
  61. Tighten the bolts to 105 inch lbs. (12 Nm).
  62.  
  63. Slide the coupler onto the column shaft and install a new coupler bolt. Tighten the coupler bolt to 36 ft. lbs. (49 Nm).
  64.  
  65. Connect the shifter cable and electrical connectors to the ignition.
  66.  
  67. Install the ignition cylinder and install the screws.
  68.  
  69. Position the ignition bezel and seat fully.
  70.  
  71. Connect the electrical connector for the multifunction switch
  72.  
  73. Install the upper shroud on the column.
  74.  
  75. Install the lower shroud to the column.
  76.  
  77. Snap the two halves back into place.
  78.  
  79. Install the three mounting bolts to secure the shroud in place.
  80.  
  81. Snap the steering column opening cover lower hinges onto the pins and roll cover up.
  82.  
  83. Seat the upper retaining clips fully.
  84.  
  85. Install the hush panel.
  86.  
  87. Connect the column electrical connectors.
  88.  
  89. Install the column covers.
  90.  
  91. Install the left a-pillar trim, the bolts and position the door seal back.
  92.  
  93. Position the left side end cap and seat fully.
  94.  
  95. Install the center support nut onto the stud.
  96.  
  97. Install the two HVAC bolts within the radio opening.
  98.  
  99. Install the radio.
  100.  
  101. Install the radio bezel.
  102.  
  103. Install the left and right center support brackets and nuts and tighten to 105 inch lbs. (12 Nm).
  104.  
  105. Position the center wire harness and connect the electrical connectors.
  106.  
  107. Install the center bezel.
  108.  
  109. Position the defroster vents and seat fully.
  110.  
  111. Connect the center harness electrical connectors (ground, module, shifter, brake lever).
  112.  
  113. Install the center floor duct.
  114.  
  115. Position the console into the vehicle and install the screws.
  116.  
  117. Connect the electrical connector and install the rear cover onto the console.
  118.  
  119. Position the shifter bezel and seat fully.
  120.  
  121. Position the shifter bezel trim ring and seat fully.
  122.  
  123. Connect the negative battery cable.
  124.  

 
label.common.footer.alt.autozoneLogo