GrandPrix, Impala 2006-2008, Monte Carlo 2006-2007

Disarming & Arming

Print

Zone 1



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the instrument panel (I/P) fuse block cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.



    Click image to see an enlarged view

    Fig. SDM fuse-2003-05 Chevrolet Impala and Monte Carlo

  10.  
  11. Remove the SDM fuse.
  12.  
  13. Remove the radiator upper air baffle and deflector.
  14.  
  15. Remove the connector position assurance (CPA) (2) from the front end sensor harness connector (3).
  16.  
  17. Disconnect the front end sensor harness connector (3) from the front end sensor (1).

    Click image to see an enlarged view

    Fig. Front end sensor harness-2003-05 Chevrolet Impala and Monte Carlo; 2005 Pontiac Grand Prix

  18.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the front end sensor harness connector (3) to the front end sensor (1).
  4.  
  5. Install the CPA (2) into the front end sensor harness connector (3).
  6.  
  7. Install the radiator upper air baffle and deflector.
  8.  
  9. Install the SDM fuse.
  10.  
  11. Install the I/P fuse block cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR fuse from the underhood fuse center.
  14.  
  15. Remove the radiator upper air baffle and deflector and locate the front end sensor also known as electronic frontal sensor (EFS).
  16.  
  17. Remove the connector position assurance (CPA) from the front end sensor connector.
  18.  
  19. Remove the front end sensor connector from the front end sensor.
  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the front end sensor connector to the front end sensor.
  4.  
  5. Install the CPA into the front end sensor connector.
  6.  
  7. Install the radiator upper air baffle and deflector.
  8.  
  9. Install the SIR Fuse.
  10.  
  11. Close the underhood fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 2



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the instrument panel (I/P) fuse block cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Remove the SDM fuse.
  12.  
  13. Remove the connector position assurance (CPA) from the left side impact sensor (SIS) connector.
  14.  
  15. Disconnect the left SIS connector from the left SIS.
  16.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the left SIS connector to the left SIS.
  4.  
  5. Install the CPA to the left SIS connector.
  6.  
  7. Install the SDM fuse.
  8.  
  9. Install the fuse block access cover.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the instrument panel (I/P) fuse block cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Remove the SDM fuse.

    Click image to see an enlarged view

    Fig. Left side impact sensor-Monte Carlo

  12.  
  13. Remove the connector position assurance (CPA) from the left side impact sensor (SIS) connector.
  14.  
  15. Disconnect the left SIS connector from the left SIS (2).
  16.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the left SIS connector to the left SIS (2).
  4.  
  5. Install the CPA to the left SIS connector.
  6.  
  7. Install the SDM fuse.
  8.  
  9. Install the fuse block access cover.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR fuse from the underhood fuse center.
  14.  
  15. When disabling the roof rail module go to step 8, if the side impact sensor (SIS) needs disabling then go to step 11.
  16.  
  17. Remove the left rear sail panel.
  18.  
  19. Remove the connector position assurance (CPA) from the left/driver roof rail module connector (2).

    Click image to see an enlarged view

    Fig. Left roof rail module-Pontiac Grand Prix

  20.  
  21. Disconnect the left roof rail module wiring harness yellow connector (2) from the left roof rail module (3).
  22.  
  23. Remove the left/driver door trim panel.

    Click image to see an enlarged view

    Fig. Side impact sensor-Pontiac Grand Prix

  24.  
  25. Remove enough of the water deflector to access the SIS.
  26.  
  27. Remove the SIS CPA from the left SIS connector (3).
  28.  
  29. Remove the SIS connector (3) from the SIS (1).
  30.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS proceed to step 3, if the roof rail module needs enabling then go to step 7.
  4.  
  5. Install the left SIS connector (3) to the SIS (1).
  6.  
  7. Install the SIS CPA to the SIS connector (3).
  8.  
  9. Replace and secure the water deflector back over the SIS.
  10.  
  11. Install the left/driver door trim panel.
  12.  
  13. Connect the left roof rail module wiring harness yellow connector (2) to the left roof rail module (3).
  14.  
  15. Install the CPA to the left roof rail module connector (2).
  16.  
  17. Install the left rear sail panel.
  18.  
  19. Close the underhood fuse center cover.
  20.  
  21. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  22.  

Zone 3



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the instrument panel (I/P) fuse block cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Remove the SDM fuse.
  12.  
  13. Remove the LH insulator panel.
  14.  
  15. Remove the connector position assurance (CPA) from the steering wheel module coil connector located at the base of the steering column.
  16.  
  17. Disconnect the steering wheel module coil connector.
  18.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the steering wheel module coil connector.
  4.  
  5. Install the CPA to the steering wheel module coil connector located at the base of the steering column.
  6.  
  7. Install the LH insulator panel.
  8.  
  9. Install the SDM fuse.
  10.  
  11. Install the I/P fuse block cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR fuse from the underhood fuse center.
  14.  
  15. Remove the left/driver sound insulator from the instrument panel (I/P) (2).
  16.  
  17. Remove the connector position assurance (CPA) from the steering wheel module coil yellow connector (1).

    Click image to see an enlarged view

    Fig. Steering wheel module coil yellow connector-Pontiac Grand Prix

  18.  
  19. Disconnect the steering wheel module coil yellow connector (1) from the vehicle harness yellow connector (3).
  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the steering wheel module coil yellow connector (3) to the vehicle harness yellow connector (1).
  4.  
  5. Install the CPA to the steering wheel module coil yellow connector (1).
  6.  
  7. Install the left sound insulator to the I/P (2).
  8.  
  9. Install the SIR Fuse.
  10.  
  11. Close the underhood fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 5



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the instrument panel (I/P) fuse block cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Remove the SDM fuse.
  12.  
  13. Remove the RH I/P access hole cover.
  14.  
  15. Remove the connector position assurance (CPA) from the I/P module connector located to the right of the steering column.
  16.  
  17. Disconnect the I/P module connector.

    Click image to see an enlarged view

    Fig. Right I/P module connector-Impala and Monte Carlo; 2005 Pontiac Grand Prix

  18.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the I/P module connector.
  4.  
  5. Install the CPA into the I/P module connector located to the right of the steering column.
  6.  
  7. Install the LH insulator panel.
  8.  
  9. Install the SDM fuse.
  10.  
  11. Install the I/P fuse block cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR Fuse from the underhood fuse center.
  14.  
  15. Remove the right/passenger sound insulator from the instrument panel (I/P).
  16.  
  17. Remove the connector position assurance (CPA) from the I/P module yellow connector.
  18.  
  19. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  20.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  4.  
  5. Install the CPA to the I/P module yellow connector.
  6.  
  7. Install the right sound insulator to the I/P.
  8.  
  9. Install the SIR Fuse.
  10.  
  11. Close the underhood fuse center cover.
  12.  
  13. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  14.  

Zone 6



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR fuse from the underhood fuse center.
  14.  
  15. When disabling the roof rail module go to step 8, if the side impact sensor (SIS) needs disabling then go to step 11.
  16.  
  17. Remove the right rear sail panel.
  18.  
  19. Remove the connector position assurance (CPA) from the right/passenger roof rail module connector.
  20.  
  21. Disconnect the right roof rail module wiring harness yellow connector from the right roof rail module.
  22.  
  23. Remove the right/passenger door trim panel.
  24.  
  25. Remove enough of the water deflector to access the SIS.
  26.  
  27. Remove the SIS CPA from the right SIS connector.
  28.  
  29. Remove the SIS connector from the SIS.
  30.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SIS proceed to step 3, if the roof rail module needs enabling then go to step 7.
  4.  
  5. Install the right SIS connector to the SIS.
  6.  
  7. Install the SIS CPA to the SIS connector.
  8.  
  9. Replace and secure the water deflector back over the SIS.
  10.  
  11. Install the right/passenger door trim panel.
  12.  
  13. Connect the right roof rail module wiring harness yellow connector to the right roof rail module.
  14.  
  15. Install the CPA to the right roof rail module connector.
  16.  
  17. Install the right rear sail panel.
  18.  
  19. Install the SIR Fuse.
  20.  
  21. Close the underhood fuse center cover.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

Zone 7



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the fuse block access cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Remove the SDM fuse.

    Click image to see an enlarged view

    Fig. Side impact module-Impala and Monte Carlo

  12.  
  13. Remove the connector position assurance (CPA) from the side impact module LF connector (1) located under the driver seat.
  14.  
  15. Disconnect the side impact module LF connector (1).
  16.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the side impact module LF connector (1) located under the driver seat.
  4.  
  5. Install the CPA to the side impact module LF connector (1).
  6.  
  7. Remove the SDM fuse.
  8.  
  9. Install the fuse block access cover.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR Fuse from the underhood fuse center.
  14.  
  15. Remove the connector position assurance (CPA) from the left/driver seat belt pretensioner connector located under the driver seat.
  16.  
  17. Disconnect the left seat belt pretensioner connector from vehicle wiring harness connector.
  18.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the left seat belt pretensioner connector to the vehicle wiring harness connector.
  4.  
  5. Install the CPA to the seat belt pretensioner connector.
  6.  
  7. Install the SIR Fuse.
  8.  
  9. Close the underhood fuse center cover.
  10.  
  11. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  12.  

Zone 9



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  4.  
  5. Turn OFF the ignition.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Remove the instrument panel (I/P) fuse block cover.
    NOTE
    With the SIR fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Remove the SDM fuse.
  12.  
  13. Remove the RH I/P access hole cover.
  14.  
  15. Remove the connector position assurance (CPA) from the I/P module connector, located at the RH side of the I/P.
  16.  
  17. Disconnect the I/P module connector.
  18.  
  19. Remove the LH insulator panel.
  20.  
  21. Remove the CPA from the steering wheel module coil connector located at the base of the steering column.
  22.  
  23. Disconnect the steering wheel module coil connector.
  24.  
  25. Remove the CPA from the side impact module LF connector (1), located under the driver seat.
  26.  
  27. Disconnect the side impact module LF connector.
  28.  

Enabling Procedure:

  1. Remove the key from the ignition.
  2.  
  3. Connect the side impact module LF connector (1), located under the driver seat.
  4.  
  5. Install the CPA to the side impact module LF connector.
  6.  
  7. Connect the steering wheel module coil connector.
  8.  
  9. Install the CPA to the steering wheel module coil connector located at the base of the steering column.
  10.  
  11. Install the LH insulator panel.
  12.  
  13. Connect the I/P module connector, located at the RH side of the I/P.
  14.  
  15. Install the CPA to the I/P module connector.
  16.  
  17. Install the RH I/P access hole cover.
  18.  
  19. Install the SDM fuse.
  20.  
  21. Install the LH I/P access hole cover.
  22.  
  23. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  24.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Open the hood and locate the underhood fuse center on right/passenger shock tower.
    NOTE
    With the SIR Fuse removed and the ignition ON, the AIR BAG indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Lift the cover for the underhood fuse center.
  12.  
  13. Locate and remove the SIR fuse from the underhood fuse center.
  14.  
  15. When disabling the SDM use the entire procedure, if the right/passenger seat belt pretensioner needs disabling then proceed to step 22.
  16.  
  17. Remove the right rear sail panel.
  18.  
  19. Remove the CPA from the right/passenger roof rail module connector.
  20.  
  21. Disconnect the right roof rail module wiring harness yellow connector from the right roof rail module.
  22.  
  23. Remove the right/passenger sound insulator from the instrument panel (I/P).
  24.  
  25. Remove the CPA from the I/P module yellow connector.
  26.  
  27. Disconnect the I/P module yellow connector from the vehicle harness yellow connector.
  28.  
  29. Remove the left/driver sound insulator from the instrument panel (I/P).
  30.  
  31. Remove the CPA from the steering wheel module coil yellow connector.
  32.  
  33. Disconnect the steering wheel module coil yellow connector from the vehicle harness yellow connector.
  34.  
  35. Remove the CPA from the left/driver seat belt pretensioner connector located under the driver seat.
  36.  
  37. Disconnect the left seat belt pretensioner connector from vehicle wiring harness connector.
  38.  
  39. Remove the left rear sail panel.
  40.  
  41. Remove the CPA from the left/driver roof rail module connector.
  42.  
  43. Disconnect the left roof rail module wiring harness yellow connector from the left roof rail module.
  44.  
  45. Remove the connector position assurance (CPA) from the right/passenger seat belt pretensioner connector located under the passenger seat.
  46.  
  47. Disconnect the right seat belt pretensioner connector from vehicle wiring harness connector.
  48.  

Enabling Procedure:

  1. Remove the key from the ignition switch.
  2.  
  3. When enabling the SDM use the entire procedure, if the right/passenger seat belt pretensioner needs enabling then proceed to step 17.
  4.  
  5. Connect the right roof rail module wiring harness yellow connector to the right roof rail module.
  6.  
  7. Install the CPA to the right roof rail module connector.
  8.  
  9. Install the right rear sail panel.
  10.  
  11. Connect the I/P module yellow connector to the vehicle harness yellow connector.
  12.  
  13. Install the CPA to the I/P module yellow connector.
  14.  
  15. Install the right sound insulator to the I/P (3).
  16.  
  17. Connect the steering wheel module coil yellow connector to the vehicle harness yellow connector.
  18.  
  19. Install the CPA to the steering wheel module coil yellow connector.
  20.  
  21. Install the left sound insulator to the I/P.
  22.  
  23. Connect the left seat belt pretensioner connector to the vehicle wiring harness connector.
  24.  
  25. Install the CPA to the seat belt pretensioner connector.
  26.  
  27. Connect the left roof rail module wiring harness yellow connector to the left roof rail module.
  28.  
  29. Install the CPA to the left roof rail module connector.
  30.  
  31. Install the left rear sail panel.
  32.  
  33. Connect the right seat belt pretensioner connector to the vehicle wiring harness connector.
  34.  
  35. Install the CPA to the seat belt pretensioner connector.
  36.  
  37. Install the SIR Fuse.
  38.  
  39. Close the underhood fuse center cover.
  40.  
  41. Use caution while reaching in and turn the ignition switch to the ON position. The AIR BAG indicator will flash then turn OFF.
  42.  

 
label.common.footer.alt.autozoneLogo