HHR 2006-2008

Disarming the System

Print

Zone 1



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.

    Click image to see an enlarged view

    Fig. BCM fuse center

  8.  
  9. Locate the Body Control Module (BCM) fuse center then remove fuse center cover.
    WARNING
    This inflatable restraint Sensing and Diagnostic Module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.

    Click image to see an enlarged view

    Fig. Front end sensor

  12.  
  13. Open front hood, and locate the front end sensor also known as the Electronic Frontal Sensor (EFS) (2).
  14.  
  15. Remove the Connector Position Assurance (CPA) from the front end sensor connector.
  16.  
  17. Remove the front end sensor connector from the front end sensor (2).
  18.  

Zone 2



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Locate the Body Control Module (BCM) fuse center then remove fuse center cover.
    WARNING
    This inflatable restraint Sensing and Diagnostic Module (SDM) has 2 fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  12.  
  13. To disable the seat belt pretensioner-RF, go to step 7. To disable the roof rail module-right go to step 10 and for the side impact sensor (SIS)-right go to step 13.
  14.  
  15. Remove the lower center pillar trim.
  16.  
  17. Remove the Connector Position Assurance (CPA) from the seat belt pretensioner-RF connector.
  18.  
  19. Disconnect the seat belt pretensioner-RF connector from the vehicle harness connector.
  20.  
  21. Remove the garnish molding from the upper lock pillar.
  22.  
  23. Remove the CPA from the roof rail module-right connector.
  24.  
  25. Disconnect the roof rail module-right connector from the vehicle harness connector.
  26.  
  27. Remove the RH door trim panel.
  28.  
  29. Peel back the door water deflector far enough to access the SIS-right.
  30.  
  31. Remove the CPA from the SIS connector.
  32.  
  33. Disconnect the SIS connector from the SIS-right.
  34.  

Zone 3



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch. Locate the Body Control Module (BCM) fuse center then remove the fuse center cover.
    WARNING
    This inflatable restraint Sensing and Diagnostic Module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  8.  
  9. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  10.  
  11. Remove the left/driver outer trim cover from the Instrument Panel (I/P).
  12.  
  13. Remove the Connector Position Assurance (CPA) from the steering wheel module coil connector.
  14.  
  15. Disconnect the steering wheel module coil connector from the vehicle harness connector.
  16.  

Zone 5



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicle-s wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Locate the Body Control Module (BCM) fuse center, then, remove the fuse center cover.
    WARNING
    This inflatable restraint Sensing and Diagnostic Module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  12.  
  13. Remove the right/passenger outer trim cover from the Instrument Panel (I/P).
  14.  
  15. Remove the Connector Position Assurance (CPA) from the I/P module connector.
  16.  
  17. Disconnect the I/P module connector from the vehicle harness connector.
  18.  

Zone 6



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Locate the Body Control Module (BCM) fuse center, then, remove fuse center cover.
    WARNING
    This inflatable restraint Sensing and Diagnostic Module (SDM) has 2 fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  12.  
  13. To disable the seat belt pretensioner-LF go to step 7. To disable the roof rail module-left go to step 10 and for the side impact sensor (SIS)-left go to step 13.
  14.  
  15. Remove the lower center pillar trim.
  16.  
  17. Remove the Connector Position Assurance (CPA) from the seat belt pretensioner-LF connector.
  18.  
  19. Disconnect the seat belt pretensioner-LF connector from the vehicle harness connector.
  20.  
  21. Remove the garnish molding from the upper lock pillar.
  22.  
  23. Remove the CPA from the roof rail module-left connector.
  24.  
  25. Disconnect the roof rail module-left connector from the vehicle harness connector.
  26.  
  27. Remove the LH door trim panel.
  28.  
  29. Peel back the door water deflector far enough to access the SIS-left.
  30.  
  31. Remove the CPA from the SIS connector.
  32.  
  33. Disconnect the SIS connector from the SIS-left.
  34.  

Zone 8



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Turn the steering wheel so that the vehicles wheels are pointing straight ahead.
  4.  
  5. Turn the ignition switch to the OFF position.
  6.  
  7. Remove the key from the ignition switch.
  8.  
  9. Locate the Body Control Module (BCM) fuse center then remove fuse center cover.
    WARNING
    This inflatable restraint Sensing and Diagnostic Module (SDM) has two fused power inputs. To ensure there is no unwanted SIR deployment, personal injury, or unnecessary SIR system repairs, remove both AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center. With the AIR BAG fuses removed and the ignition switch in the ON position, the AIR BAG warning indicator illuminates. This is normal operation, and does not indicate an SIR system malfunction.

  10.  
  11. Locate and remove the AIR BAG (IGN) and AIR BAG (BATT) fuses from the BCM fuse center.
  12.  
  13. Remove the garnish molding from the right upper lock pillar.
  14.  
  15. Remove the Connector Position Assurance (CPA) from the roof rail module-right connector.
  16.  
  17. Disconnect the roof rail module-right connector from the vehicle harness connector.
  18.  
  19. Remove the lower right center pillar trim.
  20.  
  21. Remove the CPA from seat belt pretensioner-RF connector.
  22.  
  23. Disconnect the seat belt pretensioner-RF connector from the vehicle harness connector.
  24.  
  25. Remove the passenger/right outer trim cover from the Instrument Panel (I/P). Remove the CPA from the I/P module connector.
  26.  
  27. Disconnect the I/P module connector from the vehicle harness connector.
  28.  
  29. Remove the driver/left outer trim cover from the I/P.
  30.  
  31. Remove the CPA from the steering wheel module coil connector.
  32.  
  33. Disconnect the steering wheel module coil connector from the vehicle harness connector.
  34.  
  35. Remove the lower left center pillar trim.
  36.  
  37. Remove the CPA from seat belt pretensioner-LF connector.
  38.  
  39. Disconnect the seat belt pretensioner-LF connector from the vehicle harness connector.
  40.  
  41. Remove the garnish molding from the upper lock pillar.
  42.  
  43. Remove the CPA from the roof rail module-left connector.
  44.  
  45. Disconnect the roof rail module-left connector from the vehicle harness connector.
  46.  

 
label.common.footer.alt.autozoneLogo