HHR 2006-2008

Removal & Installation

Print

2.0L Engines





Click image to see an enlarged view

Fig. ECT sensor location-2.0L engine


WARNING
Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.

  1. Turn OFF the ignition.
  2.  
  3. Drain the coolant system to below the Engine Coolant Temperature (ECT) sensor.
  4.  
  5. Disconnect the ECT sensor electrical connector.
  6.  
  7. Carefully remove the ECT sensor (1).
  8.  

To install:

  1. If you are reinstalling the original sensor, or if you are installing a new sensor without a sealer, coat the threads with sealer GM P/N 21485227, LOCTITE® 242 Threadlocker or an equivalent.
  2.  
  3. Install the ECT sensor (1). Tighten the ECT sensor to 16 ft. lbs. (22 Nm).
  4.  
  5. Connect the ECT sensor electrical connector.
  6.  
  7. Refill the engine coolant system.
  8.  
  9. Run the engine to normal operating temperature and check for leaks.
  10.  

2.2L & 2.4L Engines



  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE
    Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.

  2.  
  3. Turn ignition switch to the OFF position.
  4.  
  5. Drain the coolant system to below the Engine Coolant Temperature (ECT) sensor.
  6.  
  7. Disconnect the ECT sensor electrical connector.
  8.  
  9. If equipped with Regular Production Option (RPO) MN5, disconnect the engine harness electrical connector (3) from the Engine Coolant Temperature (ECT) sensor.
  10.  
  11. If equipped with RPO M86, disconnect the engine harness electrical connector (3) from the ECT sensor.
  12.  
  13. Carefully remove the ECT sensor.

    Click image to see an enlarged view

    Fig. Engine Coolant Temperature (ECT) sensor location (3) for regular production option RPO MN5-2.2L & 2.4L Engines



    Click image to see an enlarged view

    Fig. Engine Coolant Temperature (ECT) sensor location (3) for RPO M86-2.2L & 2.4L Engines

  14.  

To install:


NOTE
If you are reinstalling the original sensor, or if you are installing a new sensor without a sealer, coat the threads with sealer GM P/N 21485227, LOCTITE® 242 Threadlocker or an equivalent.

  1. Install the ECT sensor and tighten to 15 ft. lbs. (20 Nm).
  2.  
  3. Connect the engine harness electrical connector (3) to the ECT sensor.
  4.  
  5. Refill the engine coolant system.
  6.  

2.2L Engine





Click image to see an enlarged view

Fig. ECT sensor location-2.2L engine


WARNING
Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.

  1. Turn OFF the ignition.
  2.  
  3. Drain the coolant system to below the Engine Coolant Temperature (ECT) sensor.
  4.  
  5. Disconnect the ECT sensor electrical connector.
  6.  
  7. Carefully remove the ECT sensor.
  8.  

To install:

  1. If you are reinstalling the original sensor, or if you are installing a new sensor without a sealer, coat the threads with sealer GM P/N 12346004 (Canadian P/N 10953480) or Saturn P/N 21485278, or an equivalent.
  2.  
  3. Install the ECT sensor. Tighten the ECT sensor to 89 inch lbs. (10 Nm).
  4.  
  5. Connect the ECT sensor electrical connector.
  6.  
  7. Refill the engine coolant system.
  8.  
  9. Run the engine to normal operating temperature and check for leaks.
  10.  

2.4L Engine





Click image to see an enlarged view

Fig. ECT sensor location-RPO MN5-2.4L engine



Click image to see an enlarged view

Fig. ECT sensor location-RPO M86-2.4L engine


WARNING
Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.

  1. Drain the cooling system.
  2.  
  3. If equipped with Regular Production Option (RPO) MN5, disconnect the engine harness electrical connector (3) from the Engine Coolant Temperature (ECT) sensor.
  4.  
  5. If equipped with RPO M86, disconnect the engine harness electrical connector (3) from the ECT sensor.
  6.  
  7. Carefully remove the ECT sensor.
  8.  

To install:


WARNING
Replacement components must be the correct part number for the application. Components requiring the use of the thread locking compound, lubricants, corrosion inhibitors, or sealants are identified in the service procedure. Some replacement components may come with these coatings already applied. Do not use these coatings on components unless specified. These coatings can affect the final torque, which may affect the operation of the component. Use the correct torque specification when installing components in order to avoid damage.

  1. If you are reinstalling the original sensor, or if you are installing a NEW sensor without a sealer, coat the threads with sealant.
  2.  
  3. Install the ECT sensor. Tighten the sensor to 15 ft. lbs. (20 Nm).
  4.  
  5. If equipped with RPO M86, connect the engine harness electrical connector (3) to the ECT sensor.
  6.  
  7. If equipped with RPO MN5, connect the engine harness electrical connector (3) to the ECT sensor.
  8.  
  9. Refill the engine coolant system.
  10.  
  11. Run the engine to normal operating temperature and check for leaks.
  12.  

 
label.common.footer.alt.autozoneLogo