HHR 2006-2008

2.4L L4 VIN P Auto 7

Print

Trouble Code: P0719



TCC Brake Switch Circuit Low Input

Possible Causes:



TCC brake switch circuit is open or shorted to ground
 
TCC brake switch power circuit is open (test ABS or ERL fuse)
 
TCC brake switch is out of adjustment or damaged
 
ECM has failed
 

Trouble Code: P0722



Output Speed Sensor Circuit Low Voltage

Trouble Code: P0723



Output Speed Sensor Circuit Intermittent

Trouble Code: P0724



Brake Switch Circuit High Voltage

Trouble Code: P0724



Brake Switch Circuit High Voltage

Possible Causes:



In order to avoid a misdiagnosis, inspect for proper adjustment of the cruise control release switch. Refer to Cruise Release Switch Adjustment . For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0741



Torque Converter Clutch (TCC) System - Stuck Off

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
It is possible for an internal TCM failure which may not allow sufficient current to operate the solenoids. Verify TCM functionality by commanding the suspected solenoid ON/OFF using the scan tool and listen for a click.
 

Trouble Code: P0741



TCC System Mechanically Stuck Off

Possible Causes:



Converter clutch apply valve stuck in "off" (release) position
 
Misaligned or damaged valve body gasket
 
Restricted apply valve passage
 
TCC PWM valve exhaust orifice in damaged or it has failed
 
TCC solenoid valve mechanically stuck in "off" position
 

Trouble Code: P0742



Torque Converter Clutch (TCC) System - Stuck On

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
It is possible for an internal TCM failure which may not allow sufficient current to operate the solenoids. Verify TCM functionality by commanding the suspected solenoid ON/OFF using the scan tool and listen for a click.
 

Trouble Code: P0751



1-2 Shift solenoid (SS) Valve Performance - No First or Fourth Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
It is possible for an internal TCM failure which may not allow sufficient current to operate the solenoids. Verify TCM functionality by commanding the suspected solenoid ON/OFF using the scan tool and listen for a click.
 

Trouble Code: P0752



1-2 Shift solenoid (SS) Valve Performance - No Second or Third Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
It is possible for an internal TCM failure which may not allow sufficient current to operate the solenoids. Verify TCM functionality by commanding the suspected solenoid ON/OFF using the scan tool and listen for a click.
 

Trouble Code: P0756



2-3 Shift Solenoid (SS) Valve Performance - No First or Second Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
It is possible for an internal TCM failure which may not allow sufficient current to operate the solenoids. Verify TCM functionality by commanding the suspected solenoid ON/OFF using the scan tool and listen for a click.
 

Trouble Code: P0757



2-3 Shift Solenoid (SS) Valve Performance - No Third or Fourth Gear

Possible Causes:

If the DTC is cleared, then will not reset when the vehicle is driven, some of the following conditions may exist:



Fluid contamination
 
Plugged fluid circuits
 
Restricted fluid circuits
 
It is possible for an internal TCM failure which may not allow sufficient current to operate the solenoids. Verify TCM functionality by commanding the suspected solenoid ON/OFF using the scan tool and listen for a click.
 

Trouble Code: P0833



Clutch Pedal Switch 2 Circuit

Trouble Code: P0842



Transmission Fluid Pressure (TFP) Switch Circuit Low Voltage

Possible Causes:



Do not replace the torque converter for this condition. Refer to Torque Converter Diagnosis for other concerns.
 
Ensure the wiring harness is not stretched too tightly or other components are pressing on the AT inline 20-way connector body. Also inspect for proper clearance to any other components and wiring. Refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0843



Transmission Fluid Pressure (TFP) Switch Circuit High Voltage

Possible Causes:



Do not replace the torque converter for this condition. Refer to Torque Converter Diagnosis for other concerns.
 
Ensure the wiring harness is not stretched too tightly or other components are pressing on the AT inline 20-way connector body. Also inspect for proper clearance to any other components and wiring. Refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P0961



Line Pressure Control (PC) Solenoid System Performance

Trouble Code: P0973



1-2 Shift Solenoid (SS) Control Circuit Low Voltage

Trouble Code: P0974



1-2 Shift Solenoid (SS) Control Circuit High Voltage

Trouble Code: P0976



2-3 Shift Solenoid (SS) Control Circuit Low Voltage

Trouble Code: P0977



2-3 Shift Solenoid (SS) Control Circuit High Voltage

Trouble Code: P1101



Intake Air Flow System Performance

Trouble Code: P1101



Intake Air Flow System Performance

Possible Causes:



A steady or intermittent high resistance of 15 ohms or greater on the ignition 1 voltage circuit will cause the MAF sensor signal to be increased by as much as 60 g/s. To pinpoint this condition perform a voltage drop test on the circuit.
 
Any type of contamination on the MAF sensor heating elements will degrade the proper operation of the sensor. Certain types of contaminants act as a heat insulator, which will impair the response of the sensor to airflow changes. Water or snow can create the opposite effect, and cause the signal to increase rapidly.
 
Depending on the current ambient temperature, and the vehicle operating conditions, a MAF sensor signal circuit that is shorted to the IAT signal circuit will increase or decrease the MAF sensor signal that is interpreted by the ECM. Additionally it may cause a rapid fluctuation in the IAT Sensor parameter.
 
A skewed or stuck engine coolant temperature (ECT) or IAT sensor will cause the calculated models to be inaccurate and may cause this DTC to run when it should not. Refer to Temperature Versus Resistance .
 

Trouble Code: P1133



HO2S Insufficient Switching Sensor 1

Trouble Code: P1174



Fuel Trim Cylinder Balance

Possible Causes:



The Fuel Trim Cylinder Balance diagnostic is very sensitive to HO2S design. A non-OE sensor or an incorrect part number may set a false DTC.
 
Monitoring the misfire current counters, or misfire graph, may help to isolate the cylinder that is causing the condition.
 

Trouble Code: P1336



CKP Sensor System Variation Not Learned

Possible Causes:



Set the parking brake and block the drive wheels for safety.
 
Verify the hood is closed.
 
Read the trouble codes. If a code is set, refer to that code.
 
Start the engine. Allow engine temperature to reach at least 158°F (70°C). Then key off.
 
Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle.
 
Apply the brake pedal firmly and verify the selector is in Park.
 
Increase accelerator pedal position until fuel cutoff is reached at the test RPM (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (RPM) decreases back to idle speed and the procedure terminates.
 
Read the trouble codes and recheck for DTC P1336.
 
If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.
 

Trouble Code: P1362



ICM Control Circuit High Input

Possible Causes:



IC timing signal is shorted to system power
 
IC timing control circuit and IC timing signal circuits are shorted
 
IC module is damaged or it has failed
 
ECM has failed
 

Trouble Code: P1380



Misfire Detected, Rough Road Data Not Available

Possible Causes:



Use the Freeze Frame/Failure Records data to help find the cause on an intermittent fault. If the code cannot be duplicated, the data in the Freeze Frame/Failure Records can determine how many miles since the code set. The Fail Counter and Pass Counter can also help determine how many ignition cycles the diagnostic reported a pass or a fail. Operate the vehicle within the Freeze Frame conditions (i.e., load, engine and vehicle speed, temperature etc.). This will isolate when the code set.
 
Service the ABS before diagnosing a misfire because an actual engine misfire may or may not exist. Also, an actual engine misfire may have occurred during an ABS malfunction.
 
Determine if the vehicle was driven on a rough road, and the ABS could not detect this due to a malfunction. The ECM may interpret variations in crankshaft speed caused by the rough road as a misfire without an actual engine misfire present.
 
Refer to Diagnostic System Check for Antilock Brake System
 
Refer to Diagnostic System Check for the Engine Controls
 

Trouble Code: P1381



Misfire Detected - No Communication with Brake Control Module

Possible Causes:



If any ABS DTCs are set, diagnose those first
 
ABS module
 

Trouble Code: P1400



Cold Start Emission Reduction Control System

Possible Causes:



Any loading of the engine that lowers engine RPM, such as partial application of the clutch, A/C cycling, etc. during the first 120 seconds of the engine run time may set this DTC.
 

Trouble Code: P1400



Cold Start Emission Reduction Control System

Possible Causes:



Air intake system for Damage, restriction, or modification
 
Dirty or deteriorating air filter element
 
Crankcase ventilation system for correct operation
 
Vacuum leak and other un-metered air downstream of the Mass Air Flow (MAF) sensor
 
Intake manifold leak
 
Damaged, restricted, modified or enhanced exhaust system
 
Exhaust leaks
 

Trouble Code: P1415



Secondary Air Injection System (Bank 1) Malfunction

Possible Causes:



Air hoses disconnected, loose, kinked or failed (a burnt hose)
 
AIR pump is damaged or has failed (inspect air pump for water)
 
AIR system check valves and/or pipes are damaged or leaking
 
ECM has failed
 

Trouble Code: P1416



Secondary Air Injection System (Bank 2) Malfunction

Possible Causes:



Air hoses disconnected, loose, kinked or failed (a burnt hose)
 
AIR pump is damaged or has failed (inspect air pump for water)
 
AIR system check valves and/or pipes are damaged or leaking
 
ECM has failed
 

Trouble Code: P1516



Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance

Trouble Code: P1574



Stop Lamp Switch Circuit

Possible Causes:

In order to avoid a misdiagnosis, perform the following:



Inspect for proper operation of the stop lamps. Refer to Exterior Lighting Systems Description and Operation .
 
Inspect for proper adjustment of the stop lamps. Refer to Stop Lamp Switch Adjustment .
 
For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections .
 

Trouble Code: P1585



Cruise Control Inhibit Output Circuit Malfunction

Possible Causes:



Cruise control inhibit circuit is shorted to system voltage
 
Cruise control inhibit circuit is open or shorted to ground
 
Cruise control module power circuit is open (test CR CNT fuse)
 
Cruise control module is damaged or has failed
 
ECM has failed
 

Trouble Code: P1600



Control Module Long Term Memory Performance

Trouble Code: P1621



Control Module Long Term Memory Performance

Trouble Code: P1627



Control Module Long Term Memory Performance

Trouble Code: P1629



Theft Deterrent Fuel Enable Signal Not Received

Possible Causes:



DTC P1629 is an indicator that the challenge/response was not received within the required time. This does not necessarily indicate a fault is present with the TDM or ECM. Factors such as a long engine crank, a delay in the serial data communication, or B-codes set in the TDM will cause DTC P1629 to set. This DTC should not be used as a fault indicator, but rather as a symptom to assist in the diagnosis of these other systems.
 

Trouble Code: P1630



Theft Deterrent Learn Mode Active

 
label.common.footer.alt.autozoneLogo