Honda Accord/Prelude 1984-1995 Repair Guide

Understanding Basic Electricity


For any electrical system to operate, it must make a complete circuit. This simply means that the power flow from the battery must make a full circle. When an electrical component is operating, power flows from the battery to the components, passes through the component (load) causing it to function, and returns to the battery through the ground path of the circuit. This ground may be either another wire or the actual metal part of the car depending upon how the component is designed.

Perhaps the easiest way to visualize this is to think of connecting a light bulb with two wires attached to it to the battery. If one of the two wires was attached to the negative post of the battery and the other wire to the positive (+) post, the light bulb would light and the circuit would be complete. Electricity could follow a path from the battery to the bulb and back to the battery. Its not hard to see that with longer wires on our light bulb, it could be mounted anywhere on the car. Further, one wire could be fitted with a switch so that the light could be turned on and off at will. Various other items could be added to our primitive circuit to make the light flash, become brighter or dimmer under certain conditions or advise the user that it's burned out.

Some automotive components are grounded through their mounting points. The electrical current runs through the chassis of the vehicle and returns to the battery through the ground (-) cable; if you look, you'll see that the battery ground cable connects between the battery and the body of the car.

Every complete circuit must include a "load" (something to use the electricity coming from the source). If you were to connect a wire between the two terminals of the battery (DON'T do this) without the light bulb, the battery would attempt to deliver its entire power supply from one pole to another almost instantly. This is a short circuit. The electricity is taking a short cut to get to ground and is not being used by any load in the circuit. This sudden and uncontrolled electrical flow can cause great damage to other components in the circuit and can develop a tremendous amount of heat. A short in an automotive wiring harness can develop sufficient heat to melt the insulation on all the surrounding wires and reduce a multiple wire cable to one sad lump of plastic and copper. Two common causes of shorts are broken insulation (thereby exposing the wire to contact with surrounding metal surfaces or other wires) or a failed switch (the pins inside the switch come out of place and touch each other).

Some electrical components which require a large amount of current to operate also have a relay in their circuit. Since these circuits carry a large amount of current (amperage or amps), the thickness of the wire in the circuit (wire gauge) is also greater. If this large wire were connected from the load to the control switch on the dash, the switch would have to carry the high amperage load and the dash would be twice as large to accommodate wiring harnesses as thick as your wrist. To prevent these problems, a relay is used. The large wires in the circuit are connected from the battery to one side of the relay and from the opposite side of the relay to the load. The relay is normally open, preventing current from passing through the circuit. An additional, smaller wire is connected from the relay to the control switch for the circuit. When the control switch is turned on, it grounds the smaller wire to the relay and completes its circuit. The main switch inside the relay closes, sending power to the component without routing the main power through the inside of the car. Some common circuits which may use relays are the horn, headlights, starter and rear window defogger systems.

It is possible for larger surges of current to pass through the electrical system of your car. If this surge of current were to reach the load in the circuit, it could burn it out or severely damage it. To prevent this, fuses, circuit breakers and/or fusible links are connected into the supply wires of the electrical system. These items are nothing more than a built-in weak spot in the system. It's much easier to go to a known location (the fusebox) to see why a circuit is inoperative than to dissect 15 feet of wiring under the dashboard, looking for what happened.

When an electrical current of excessive power passes through the fuse, the fuse blows and breaks the circuit, preventing the passage of current and protecting the components.

A circuit breaker is basically a self repairing fuse. It will open the circuit in the same fashion as a fuse, but when either the short is removed or the surge subsides, the circuit breaker resets itself and does not need replacement.

A fuse link (fusible link or main link) is a wire that acts as a fuse. One of these is normally connected between the starter relay and the main wiring harness under the hood. Since the starter is the highest electrical draw on the car, an internal short during starting could direct about 130 amps into the wrong places. Consider the damage potential of introducing this current into a system whose wiring is rated at 15 amps and you'll understand the need for protection. Since this link is very early in the electrical path, it's the first place to look if nothing on the car works but the battery seems to be charged and is properly connected.

Electrical problems generally fall into one of three areas:

The component that is not functioning is not receiving current.
The component is receiving power but not using it or using it incorrectly (component failure).
The component is improperly grounded.

The circuit can be can be checked with a test light and a jumper wire. The test light is a device that looks like a pointed screwdriver with a wire on one end and a bulb in its handle. A jumper wire is simply a piece of wire with alligator clips on each end. If a component is not working, you must follow a systematic plan to determine which of the three causes is the villain.

  1. Turn on the switch that controls the inoperative item.

Some items only work when the ignition switch is turned


  1. Disconnect the the power supply wire from the component.
  3. Attach the ground wire on the test light to a good metal ground.
  5. Touch the end probe of the test light to the power wire; if there is current in the wire, the light in the test light will come on. You have now established that current is getting to the component.
  7. Turn the ignition or dash switch OFF and reconnect the wire to the component.

If the test light did not go on, then the problem is between the battery and the component. This includes all the switches, fuses, relays and the battery itself. The next place to look is the fusebox; check carefully either by eye or by using the test light across the fuse clips. The easiest way to check is to simply replace the fuse. If the fuse is blown, and upon replacement, immediately blows again, there is a short between the fuse and the component. This is generally (not always) a sign of an internal short in the component. Disconnect the power wire at the component again and replace the fuse; if the fuse holds, the component is the problem.

If all the fuses are good and the component is not receiving power, find the switch for the circuit. Bypass the switch with the jumper wire. This is done by connecting one end of the jumper to the power wire coming into the switch and the other end to the wire leaving the switch. If the component comes to life, the switch has failed.

Never substitute the jumper for the component. The circuit needs the electrical load of the component. If you bypass it, you will cause a short circuit.

Checking the ground for any circuit can mean tracing wires to the body, cleaning connections or tightening mounting bolts for the component itself. If the jumper wire can be connected to the case of the component or the ground connector, you can ground the other end to a piece of clean, solid metal on the car. Again, if the component starts working, you've found the problem.

A systematic search through the fuse, connectors, switches and the component itself will almost always yield an answer. Loose and/or corroded connectors, particularly in ground circuits, are becoming a larger problem in modern cars. The computers and on-board electronic (solid state) systems are highly sensitive to improper grounds and will change their function drastically if one occurs.

Remember that for any electrical circuit to work, ALL the connections must be clean and tight.