Honda - Accord Prelude 1996 2000

General Information


The charging system used on the Honda Accord and Prelude models is a 12 volt DC (Direct Current) negative (-) ground system. The system consists of an alternator with an internal voltage regulator, an alternator belt, a charging system light, an under-hood fuse/relay box with a built-in Electrical Load Detector (ELD) Unit, and a battery.

The Powertrain Control Module (PCM) is used as part of the alternator control system by means of sending a signal to the voltage regulator. The signal is used by the regulator to change the voltage generated by the alternator according to the vehicle's operating conditions to improve fuel economy.

The alternator is mounted onto the engine and the alternator rotor is supported by two sealed bearings within the alternator housing. One end of the alternator rotor has two electrical contacts called slip rings, and the other end of the rotor's shaft protrudes through the alternator housing and has a pulley attached to it. The rotor shaft's pulley is belt-driven by another pulley that is attached to the engine's crankshaft.

Click image to see an enlarged view

Fig. Typical charging system components-4-cylinder engine shown

Click image to see an enlarged view

Fig. Charging system component locations on a V6 engine

The slip rings are electrical contacts that allow voltage to be supplied to the rotor's electrical windings while it spins. The voltage is supplied to the two slip rings via a pair of spring loaded brushes. The brushes are soft enough to not damage the slip rings, yet are made of a material that will conduct an electrical current. The rotor has an electrical winding that is surrounded by a series of metal fingers.

The initial voltage is supplied to the rotor from the battery and is called the excitation current. This electrical current is used to energize the field to begin the generation of electricity. When the electrical current is supplied to the rotor field winding via the slip rings, the rotor becomes an electromagnet. The rotor is surrounded by a series of small electrical coils called the stator assembly. When the rotor spins, the magnetic field from the rotor is absorbed by the electrical coils of the stator assembly. This generates a series of positive and negative electrical pulses in the coils of the stator assembly creating an Alternating Current (AC) and AC voltage.

Because the vehicle's battery, electrical system and the electrical accessories are DC voltage, the AC voltage must be converted to DC voltage. The alternating current from the stator assembly is channeled through a series of diodes that are grouped together to form a component known as the rectifier. A diode is essentially a one way valve, and designed to allow current to pass in only one direction. The collection of diodes that form the rectifier assembly allows the current to flow in one direction, changing the electrical pulses from Alternating Current (AC voltage) to Direct Current (DC voltage). Once the alternator rotor begins to rotate and starts to generate electricity, the excitation current comes from its own output, rather than from the battery, although the battery remains as part of the electrical circuit.

Because the electrical needs of the vehicle change depending on operating conditions, the alternator's output needs to be regulated. To accomplish this, a voltage regulator is used to control the alternator's output. To do this, the regulator controls the voltage to the alternator rotor, which regulates the alternator's output by controlling the strength of the magnetic field. The more voltage the rotor receives, the stronger the magnetic field, and the more electrical current the alternator provides. Conversely, the less voltage the rotor receives, the weaker the magnetic field, and the less electrical current the alternator provides.

The alternator is used to maintain the charge of the battery and to power the components of the electrical system. When the ignition key is turned ON , current flows from the battery, through the charging system indicator light on the instrument panel, and to the voltage regulator in the alternator. When the alternator rotor is not moving, the alternator is not producing an electrical current, and the alternator warning light remains on. When the engine is started, the alternator rotor begins to rotate. As the alternator rotor rotates, the alternator generates an electrical current and turns the alternator light off.

When the engine is running, the alternator produces an electrical current that is used to replenish the battery, which is drained slightly during start-up, and to power the electrical components of the vehicle. The Powertrain Control Module (PCM) fine tunes the alternator output by monitoring the vehicle's electrical demands. The PCM sends a signal to the voltage regulator that allows the regulator to maximize the efficiency of the alternator to improve fuel economy.