Honda Cars 2007-2008

Crankshaft Damper (Balancer)

Print

Removal & Installation




NOTE
This procedure requires the use of the following special tools, or their equivalents: Socket, 19 mm 07JAA-001020A, Holder handle 07JAB-001020B and Holder attachment, 50 mm 07NAB-001040A.

  1. Hold the pulley with holder handle (A) and holder attachment (B).
  2.  
  3. Remove the bolt with a heavy duty 19 mm socket (C) and breaker bar.

    Click image to see an enlarged view

    Fig. Hold the pulley with holder handle (A) and holder attachment (B), then remove the bolt with a heavy duty 19 mm socket (C) and breaker bar-S2000 Models

  4.  

To install:

  1. Clean the bolt (A), washer (B), pulley (C), and crankshaft (D). Lubricate with new engine oil as shown.

    Click image to see an enlarged view

    Fig. Clean the bolt (A), washer (B), pulley (C), and crankshaft (D). Lubricate with new engine oil as shown-S2000 Models

  2.  
  3. Install the crankshaft pulley, and tighten the bolt to 192 ft. lbs. (260 Nm), as follows. Do not use an impact wrench.
    1. Hold the pulley with the holder handle (A) and holder attachment (B).
    2.  
    3. Tighten the bolt with a torque wrench and heavy duty 19 mm socket (C).

      Click image to see an enlarged view

      Fig. Crankshaft pulley installation-S2000 Models

    4.  

  4.  

2.4L Engine

Specific to:

Honda Accord 2007-2008


NOTE
This procedure requires the use of the following special tools or their equivalents: Holder handle 07JAB-001020A, 50mm Holder attachment 07NAB-001040A and 19mm Socket 07JAA-001020A.

  1. Raise and safely support the vehicle.
  2.  
  3. Remove the front wheels.
  4.  
  5. Remove the splash shield.
  6.  
  7. Remove the drive belt.
  8.  
  9. Hold the pulley with holder handle (A) and holder attachment (B).
  10.  
  11. Remove the bolt with a 19 mm socket (C) and breaker bar, and then remove the crankshaft.

    Click image to see an enlarged view

    Fig. While holding the pulley with holder handle (A) and holder attachment (B), remove the bolt with a heavy duty 19mm socket (C) and breaker bar-Accord 2.4L Engine

  12.  

To install:

  1. Clean the crankshaft pulley (A), crankshaft (B), bolt (C), and washer (D). Lubricate as shown.

    Click image to see an enlarged view

    Fig. Clean the crankshaft pulley (A), crankshaft (B), bolt (C), and washer (D). Lubricate with new engine oil as shown-Accord 2.4L Engine

  2.  
  3. Tighten the crankshaft pulley bolt, as follows: Do not use an impact wrench.
    1. Hold the pulley with the holder handle (A) and pulley holder attachment (B). Torque the bolt to 36 ft. lbs. (49 Nm) with a torque wrench and a heavy duty 19 mm socket (C).
    2.  
    3. Mark the bolt head (D) and the crankshaft pulley (E) as shown, and then tighten the bolt an additional 90°. The mark on the bolt head should line up with the mark on the crankshaft pulley.

      Click image to see an enlarged view

      Fig. Mark the bolt head (D) and the crankshaft pulley (E) as shown, then tighten the bolt an additional 90°. The mark on the bolt head should line up with the mark on the crankshaft pulley-Accord 2.4L Engine

    4.  

  4.  
  5. Install the drive belt.
  6.  
  7. Install the splash shield.
  8.  
  9. Install the front wheels.
  10.  
  11. Carefully lower the vehicle.
  12.  

3.0L & 3.5L Engines

Specific to:

Honda Accord 2007-2008


NOTE
This procedure requires the use of the following special tools or their equivalents: Holder handle 07JAB-001020A, Offset 50mm Holder attachment 07MAB-PY3010A and 19mm Socket 07JAA-001020A.

  1. Raise and safely support the vehicle.
  2.  
  3. Remove the right front wheel.
  4.  
  5. Remove the splash shield.
  6.  
  7. Remove the drive belt.
  8.  
  9. Hold the pulley with the holder handle (A) and holder attachment (B).
  10.  
  11. Remove the bolt with a heavy duty 19 mm socket (C) and breaker bar, and then remove the crankshaft pulley.

    Click image to see an enlarged view

    Fig. Hold the pulley with the holder handle (A) and holder attachment (B). Remove the bolt with a heavy duty 19 mm socket (C) and breaker bar, then remove the crankshaft pulley-3.0L Engine shown

  12.  

To install:

  1. Clean the crankshaft pulleys (A), crankshaft (B), bolt (C), and washer (D). Lubricate with new engine oil as shown.

    Click image to see an enlarged view

    Fig. Clean the crankshaft pulleys (A), crankshaft (B), bolt (C), and washer (D). Lubricate with new engine oil as shown-3.0L Engine shown

  2.  
  3. Install the crankshaft pulley, and tighten the bolt, as follows. Do not use an impact wrench.
    1. Hold the pulley with the holder handle (A) and holder attachment (B), and then tighten the bolt to 47 ft. lbs. (64 Nm) with a torque wrench and 19 mm socket (C).
    2.  
    3. Mark (D) the bolt head and crankshaft pulley as shown, and then tighten the bolt an additional 60° (The mark on the bolt head should line up with the mark on the crankshaft pulley).

      Click image to see an enlarged view

      Fig. Mark (D) the bolt head and crankshaft pulley as shown, then tighten the bolt an additional 60° (The mark on the bolt head should line up with the mark on the crankshaft pulley)-3.0L Engine shown

    4.  

  4.  
  5. Install the drive belt.
  6.  
  7. Install the splash shield.
  8.  
  9. Install the right front wheel.
  10.  

 
label.common.footer.alt.autozoneLogo