Honda Cars 2007-2008

Throttle Body

Print

Removal & Installation



Specific to:

Honda S2000 2007-2008

  1. Refer to the accompanying illustration for Throttle Body replacement.
    NOTE
    Do not adjust the throttle stop screw. The TP sensor is not removable.



    Click image to see an enlarged view

    Fig. Throttle body removal and installation

  2.  

To install:

  1. After reassembly, adjust the cruise control actuator cable, as follows:
    1. Hold the cable sheath, removing all slack from the throttle cable.
    2.  
    3. Turn the adjusting nut until it is 3 mm ( 1 / 8 in.) away from the throttle cable bracket. Tighten the locknut. The throttle cable deflection should now be 4-6 mm (0.16-0.24 in.).

      Click image to see an enlarged view

      Fig. Turn the adjusting nut (A) until it is 3 mm (1/8 in.) away from the throttle cable bracket. Tighten the locknut (B). The throttle cable deflection should now be 4-6 mm (0.16-0.24 in.)

    4.  
    5. Remove the actuator cover, and then disconnect the actuator cable end from the cruise control actuator.
    6.  
    7. Turn the adjusting nut until it is 9 mm (0.35 in.) away from the actuator cable bracket when the throttle linkage starts open.

      Click image to see an enlarged view

      Fig. Turn the adjusting nut (A) until it is 9 mm (0.35 in.) away from the actuator cable bracket when the throttle linkage starts open

    8.  
    9. Pull the cable so the adjusting nut touches the bracket, and tighten the locknut.
    10.  
    11. Make sure the throttle linkage starts open when the actuator cable is pulled 9 mm (0.35 in.) from the starting point by rotating the actuator linkage.

      Click image to see an enlarged view

      Fig. Pull the cable so the adjusting nut (A) touches the bracket, and tighten the locknut (B). Make sure the throttle linkage starts open when the actuator cable is pulled 9 mm (0.35 in.) from the starting point by rotating the actuator linkage.

    12.  

  2.  
  3. Adjust the throttle cable as follows:
    1. Check cable free play at the throttle linkage. Cable free play should be 4-6 mm ( 3 / 16 - 1 / 4 in.).
    2.  
    3. If free play is not within spec (4-6 mm, 3 / 16 - 1 / 4 in.) loosen the locknut, turn the adjusting nut until the free play is as specified, and then retighten the locknut.
    4.  
    5. With the cable properly adjusted, check the throttle valve to be sure it opens fully when you push the accelerator pedal to the floor. Also check the throttle valve to be sure it returns to the idle position whenever you release the accelerator pedal.

      Click image to see an enlarged view

      Fig. Throttle cable adjustment

    6.  

  4.  

Specific to:

Honda Fit 2007-2008


CAUTION
Do not insert fingers into the installed throttle body when turning the ignition switch ON (II) or while the ignition switch is ON (II). Serious injury to fingers will result if the throttle valve is activated.


NOTE
If replacing or cleaning the throttle body, start at step 1. If removing the throttle body, start at step 5.

  1. Connect the HDS while the engine is stopped.
  2.  
  3. Select the INSPECTION MENU on the scan tool.
  4.  
  5. Do the TP POSITION CHECK in the ETCS TEST.
  6.  
  7. Turn the ignition switch OFF.
  8.  
  9. Remove the air cleaner.
  10.  
  11. Disconnect the throttle body connector and the EVAP canister purge valve connector.
  12.  
  13. Disconnect and plug the water bypass hoses.
  14.  
  15. Disconnect the vacuum hose.
  16.  
  17. Remove the throttle body.

    Click image to see an enlarged view

    Fig. Removing the throttle body

  18.  

To install:

  1. Install the parts in the reverse order of removal with a new gasket.
  2.  
  3. Tighten the retaining bolts to 17 ft. lbs. (24 Nm).
  4.  
  5. Perform the ECM/PCM idle learn procedure after replacing throttle body as follows:
    1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
    2.  
    3. Reset the ECM/PCM with the scan tool.
    4.  
    5. Turn the ignition switch ON (II), and wait 2 seconds.
    6.  
    7. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, or until the engine coolant temperature reaches 194°F (90°C).
    8.  
    9. Let the engine idle for about 5 minutes with the throttle fully closed.
      NOTE
      If the radiator fan comes on, do not include its running time in the 5 minutes.

    10.  

  6.  
  7. Refill the radiator with engine coolant.
  8.  

2.4L Engines

Specific to:

Honda Accord 2007-2008

  1. Disconnect the negative battery cable.
  2.  
  3. Disconnect the IAT sensor connector.
  4.  
  5. Remove the intake air duct.
  6.  
  7. Disconnect the IAC valve connector, and the Throttle Position (TP) sensor connector.
  8.  
  9. Disconnect and plug the water bypass hoses.
  10.  
  11. Disconnect the vacuum hose.
  12.  
  13. Remove the throttle cable and actuator cable (with cruise control).
  14.  
  15. Remove the harness clip and throttle body.
    NOTE
    The TP sensor is not removable.



    Click image to see an enlarged view

    Fig. Exploded view of the throttle body-2.4L Engines

  16.  

To install:

  1. Install the parts in the reverse order of removal with a new gasket (K).
    NOTE
    Do not adjust the throttle stop screw (L).

  2.  
  3. Do the ECM/PCM idle learn procedure after the throttle body has been replaced:
    1. Make sure all electrical items (A/C, audio, rear window defogger, lights, etc.) are off.
    2.  
    3. Reset the ECM/PCM with the HDS.
    4.  
    5. Turn the ignition switch ON (II), and wait 2 seconds.
    6.  
    7. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, or until the engine coolant temperature reaches 194°F (90°C).
    8.  
    9. Let the engine idle for about 5 minutes with the throttle fully closed.
      NOTE
      If the radiator fan comes on, do not include its running time in the 5 minutes.

    10.  

  4.  
  5. Refill the radiator with engine coolant.
  6.  
  7. After reassembly, adjust the cruise control cable:
    1. Check that the actuator cable (A) moves smoothly with no binding or sticking.
    2.  
    3. Measure the amount of movement of the output linkage (B) until the engine speed starts to increase.
    4.  
    5. At first, the output linkage should be located at the fully closed position (C). The free play (D) should be 3.75, plus/minus 0.5 mm (0.15, plus/minus 0.02 in.).
    6.  
    7. If the free play is not within specification, loosen the locknut (E), and turn the adjusting nut (F) until the free play is as specified, and then retighten the locknut.

      Click image to see an enlarged view

      Fig. Cruise control cable adjustment

    8.  

  8.  
  9. Adjust the throttle cable as follows:
    1. Check cable free play at the throttle linkage. Cable free play (A) should be 3 / 8 - 1 / 2 in. (10-12 mm).
    2.  
    3. If the free play is not within spec ( 3 / 8 - 1 / 2 in., 10-12 mm), loosen the locknut (B), turn the adjusting nut (C) until the free play is as specified, and then retighten the locknut.
    4.  
    5. With the cable properly adjusted, check the throttle valve to be sure it opens fully when you push the accelerator pedal to the floor. Also check the throttle valve to be sure it returns to the idle position whenever you release the accelerator pedal.

      Click image to see an enlarged view

      Fig. Throttle cable adjustment

    6.  

  10.  

3.0L & 3.5L Engines

Specific to:

Honda Accord 2007-2008


NOTE
If you are replacing or cleaning the throttle body, begin from step 1. If you are removing the throttle body temporarily, begin from step 4.

  1. Connect the HDS while the engine is stopped.
  2.  
  3. Select the INSPECTION MENU with the HDS.
  4.  
  5. Do the TP POSITION CHECK in the ETCS TEST.
  6.  
  7. Disconnect the MAP sensor connector (A).
  8.  
  9. Remove the intake air duct (B).
  10.  
  11. Disconnect the throttle body connector (C).
  12.  
  13. Disconnect and plug the water bypass hoses (D).
  14.  
  15. Remove the harness clip (E) and the throttle body (F).
  16.  

To install:

  1. Install the parts in the reverse order of removal with a new gasket (G).
  2.  
  3. Do the ECM/PCM idle learn procedure after the throttle body has been replaced, as follows:
    1. Make sure all electrical items (A/C, audio, rear window defogger, lights, etc.) are off.
    2.  
    3. Reset the ECM/PCM with the HDS.
    4.  
    5. Turn the ignition switch ON (II), and wait for 2 seconds.
    6.  
    7. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, or until the engine coolant temperature reaches 194°F (90°C).
    8.  
    9. Let the engine idle for about 5 minutes with the throttle fully closed.
      NOTE
      If the radiator fan comes on, do not include its running time in the 5 minutes.

    10.  

  4.  
  5. Refill the radiator with engine coolant.

    Click image to see an enlarged view

    Fig. Exploded view of the throttle body-3.0L engine shown

  6.  

Hybrid

Specific to:

Honda Civic 2007-2008

  1. Connect the HDS to the DLC while the engine is stopped.
  2.  
  3. Select the INSPECTION MENU on the HDS.
  4.  
  5. Do the TP POSITION CHECK in the ETCS TEST.
  6.  
  7. Turn the ignition switch to LOCK (0).
  8.  
  9. Remove the cowl cover and under-cowl panel.
  10.  
  11. Remove the air cleaner, and the intake air duct.
  12.  
  13. Disconnect the throttle body connector.
  14.  
  15. Disconnect and plug the water bypass hoses and vacuum hose.
  16.  
  17. Remove the throttle body.
  18.  

To install:

  1. Install the parts in the reverse order of removal with a new gasket.
  2.  

Non-hybrid
1.8L Engine

Specific to:

Honda Civic 2007-2008


NOTE
If you are replacing or cleaning the throttle body, start at step 1. If you are removing the throttle body, start at step 4.

  1. Connect the HDS to the DLC while the engine is stopped.
  2.  
  3. Select the INSPECTION MENU on the HDS.
  4.  
  5. Do the TP POSITION CHECK in the ETCS TEST.
  6.  
  7. Remove the cowl cover and under-cowl panel.
  8.  
  9. Remove the air cleaner.
  10.  
  11. Disconnect the throttle body connector and the EVAP purge control solenoid valve connector.
  12.  
  13. Disconnect and plug the water bypass hoses.
  14.  
  15. Remove the throttle body.
  16.  

To install:

  1. Install the parts in the reverse order of removal with a new gasket.
  2.  
  3. Do the ECM/PCM idle learn procedure after replacing throttle body, as follows:
    1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
    2.  
    3. Reset the ECM/PCM with the HDS.
    4.  
    5. Turn the ignition switch ON (II), and wait 2 seconds.
    6.  
    7. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, or until the engine coolant temperature reaches 194°F (90°C).
    8.  
    9. Let the engine idle for about 5 minutes with the throttle fully closed.
      NOTE
      If the radiator fan comes on, do not include its running time in the 5 minutes.

    10.  
    11. Verify on the HDS data list that the idle learn procedure is complete.
    12.  

  4.  
  5. Refill the radiator with engine coolant.
  6.  

2.0L Engine

Specific to:

Honda Civic 2007-2008


WARNING
Do not insert your fingers into the installed throttle body when you turn the ignition switch ON (II) or while the ignition switch is ON (II). If you do, there will be serious injury to your fingers if the throttle valve is activated.


NOTE
If you are replacing or cleaning the throttle body, start at step 1. If you are removing the throttle body, start at step 4.

  1. Connect the HDS to the DLC while the engine is stopped.
  2.  
  3. Select the INSPECTION MENU on the HDS.
  4.  
  5. Do the TP POSITION CHECK in the ETCS TEST.
  6.  
  7. Remove the air intake duct.
  8.  
  9. Disconnect the throttle body connector.
  10.  
  11. Disconnect the water bypass hoses, and plug the water bypass hoses.
  12.  
  13. Disconnect the vacuum hose and clamp.
  14.  
  15. Remove the throttle body.
  16.  
  17. Install the parts in the reverse order of removal with a new gasket, and then check these items:
  18.  
  19. Do the ECM idle learn procedure after replacing the throttle body, as follows:
    1. Make sure all electrical items (A/C, audio, lights, etc.) are off.
    2.  
    3. Reset the ECM with the HDS.
    4.  
    5. Turn the ignition switch ON (II), and wait 2 seconds.
    6.  
    7. Start the engine. Hold the engine speed at 3,000 rpm without load (in neutral) until the radiator fan comes on, or until the engine coolant temperature reaches 194°F (90°C).
    8.  
    9. Let the engine idle for about 5 minutes with the throttle fully closed.
      NOTE
      If the radiator fan comes on, do not include its running time in the 5 minutes.

    10.  
    11. Verify on the HDS data list that the idle learn procedure is complete.
    12.  

  20.  
  21. Refill the radiator with engine coolant.

    Click image to see an enlarged view

    Fig. Exploded view of the throttle body-2.0L engine

  22.  

 
label.common.footer.alt.autozoneLogo