Honda Civic/CRX/del Sol 1984-1995 Repair Guide

Wiring Harnesses


The average automobile contains about 1 / 2 mile of wiring, with hundreds of individual connections. To protect the many wires from damage and to keep them from becoming a confusing tangle, they are organized into bundles, enclosed in plastic or taped together and called wiring harnesses. Different harnesses serve different parts of the vehicle. Individual wires are color coded to help trace them through a harness where sections are hidden from view.

Automotive wiring or circuit conductors can be in any one of three forms:

  1. Single strand wire
  3. Multi-strand wire
  5. Printed circuitry

Single strand wire has a solid metal core and is usually used inside such components as alternators, motors, relays and other devices. Multi-strand wire has a core made of many small strands of wire twisted together into a single conductor. Most of the wiring in an automotive electrical system is made up of multi-strand wire, either as a single conductor or grouped together in a harness. All wiring is color coded on the insulator, either as a solid color or as a colored wire with an identification stripe. A printed circuit is a thin film of copper or other conductor that is printed on an insulator backing. Occasionally, a printed circuit is sandwiched between two sheets of plastic for more protection and flexibility. A complete printed circuit, consisting of conductors, insulating material and connectors for lamps or other components is called a printed circuit board. Printed circuitry is used in place of individual wires or harnesses in places where space is limited, such as behind instrument panels.

Since automotive electrical systems are very sensitive to changes in resistance, the selection of properly sized wires is critical when systems are repaired. A loose or corroded connection or a replacement wire that is too small for the circuit will add extra resistance and an additional voltage drop to the circuit. A ten percent voltage drop can result in slow or erratic motor operation, for example, even though the circuit is complete. The wire gauge number is an expression of the cross-sectional area of the conductor. The most common system for expressing wire size is the American Wire Gauge (AWG) system.

Gauge numbers are assigned to conductors of various cross-sectional areas. As gauge number increases, area decreases and the conductor becomes smaller. A 5 gauge conductor is smaller than a 1 gauge conductor and a 10 gauge is smaller than a 5 gauge. As the cross-sectional area of a conductor decreases, resistance increases and so does the gauge number. A conductor with a higher gauge number will carry less current than a conductor with a lower gauge number.

Gauge wire size refers to the size of the conductor, not the size of the complete wire. It is possible to have two wires of the same gauge with different diameters because one may have thicker insulation than the other.

12 volt automotive electrical systems generally use 10, 12, 14, 16 and 18 gauge wire. Main power distribution circuits and larger accessories usually use 10 and 12 gauge wire. Battery cables are usually 4 or 6 gauge, although 1 and 2 gauge wires are occasionally used. Wire length must also be considered when making repairs to a circuit. As conductor length increases, so does resistance. An 18 gauge wire, for example, can carry a 10 amp load for 10 feet without excessive voltage drop; however if a 15 foot wire is required for the same 10 amp load, it must be a 16 gauge wire.

An electrical schematic shows the electrical current paths when a circuit is operating properly. It is essential to understand how a circuit works before trying to figure out why it doesn't. Schematics break the entire electrical system down into individual circuits and show only one particular circuit. In a schematic, no attempt is made to represent wiring and components as they physically appear on the vehicle; switches and other components are shown as simply as possible. Face views of harness connectors show the cavity or terminal locations in all multi-pin connectors to help locate test points.

If you need to backprobe a connector while it is on the component, the order of the terminals must be mentally reversed. The wire color code can help in this situation, as well as a keyway, lock tab or other reference mark.


Soldering is a quick, efficient method of joining metals permanently. Everyone who has the occasion to make wiring repairs should know how to solder. Electrical connections that are soldered are far less likely to come apart and will conduct electricity much better than connections that are only "pig-tailed" together. The most popular (and preferred) method of soldering is with an electrical soldering gun. Soldering irons are available in many sizes and wattage ratings. Irons with higher wattage ratings deliver higher temperatures and recover lost heat faster. A small soldering iron rated for no more than 50 watts is recommended, especially on electrical systems where excess heat can damage the components being soldered.

There are three ingredients necessary for successful soldering; proper flux, good solder and sufficient heat. A soldering flux is necessary to clean the metal of tarnish, prepare it for soldering and to enable the solder to spread into tiny crevices. When soldering, always use a rosin core solder which is non-corrosive and will not attract moisture once the job is finished. Other types of flux (acid core) will leave a residue that will attract moisture and cause the wires to corrode. Tin is a unique metal with a low melting point. In a molten state, it dissolves and alloys easily with many metals. Solder is made by mixing tin with lead. The most common proportions are 40/60, 50/50 and 60/40, with the percentage of tin listed first. Low priced solders usually contain less tin, making them very difficult for a beginner to use because more heat is required to melt the solder. A common solder is 40/60 which is well suited for all-around general use, but 60/40 melts easier and is preferred for electrical work.

Soldering Techniques

Successful soldering requires that the metals to be joined be heated to a temperature that will melt the solder, usually 360-460°F (182-238°C). Contrary to popular belief, the purpose of the soldering iron is not to melt the solder itself, but to heat the parts being soldered to a temperature high enough to melt the solder when it is touched to the work. Melting flux-cored solder on the soldering iron will usually destroy the effectiveness of the flux.

Soldering tips are made of copper for good heat conductivity, but must be "tinned" regularly for quick transference of heat to the project and to prevent the solder from sticking to the iron. To "tin" the iron, simply heat it and touch the flux-cored solder to the tip; the solder will flow over the hot tip. Wipe the excess off with a clean rag, but be careful as the iron will be hot.

After some use, the tip may become pitted. If so, simply dress the tip smooth with a smooth file and "tin" the tip again. Flux-cored solder will remove oxides but rust, bits of insulation and oil or grease must be removed with a wire brush or emery cloth. For maximum strength in soldered parts, the joint must start off clean and tight. Weak joints will result in gaps too wide for the solder to bridge.

If a separate soldering flux is used, it should be brushed or swabbed on only those areas that are to be soldered. Most solders contain a core of flux and separate fluxing is unnecessary. Hold the work to be soldered firmly. It is best to solder on a wooden board, because a metal vise will only rob the piece to be soldered of heat and make it difficult to melt the solder. Hold the soldering tip with the broadest face against the work to be soldered. Apply solder under the tip close to the work, using enough solder to give a heavy film between the iron and the piece being soldered, while moving slowly and making sure the solder melts properly. Keep the work level or the solder will run to the lowest part and favor the thicker parts, because these require more heat to melt the solder. If the soldering tip overheats (the solder coating on the face of the tip burns up), it should be retinned. Once the soldering is completed, let the soldered joint stand until cool. Tape and seal all soldered wire splices after the repair has cooled.

Wire Harness Connectors

Most connectors in the engine compartment or otherwise exposed to the elements are protected against moisture and dirt which could create oxidation and deposits on the terminals.

These special connectors are weather-proof. All repairs require the use of a special terminal and the tool required to service it. This tool is used to remove the pin and sleeve terminals. If removal is attempted with an ordinary pick, there is a good chance that the terminal will be bent or deformed. Unlike standard blade type terminals, these weather-proof terminals cannot be straightened once they are bent. Make certain that the connectors are properly seated and all of the sealing rings are in place when connecting leads. On some models, a hinge-type flap provides a backup or secondary locking feature for the terminals. Most secondary locks are used to improve connector reliability by retaining the terminals if the small terminal lock tangs are not positioned properly.

Molded-on connectors require complete replacement of the connection. This means splicing a new connector assembly into the harness. All splices should be soldered to insure proper contact. Use care when probing the connections or replacing terminals in them as it is possible to short between opposite terminals. If this happens to the wrong terminal pair, it is possible to damage certain components. Always use jumper wires between connectors for circuit checking and never probe through weatherproof seals.

Open circuits are often difficult to locate by sight because corrosion or terminal misalignment are hidden by the connectors. Merely wiggling a connector on a sensor or in the wiring harness may correct the open circuit condition. This should always be considered when an open circuit or a failed sensor is indicated. Intermittent problems may also be caused by oxidized or loose connections. When using a circuit tester for diagnosis, always probe connections from the wire side. Be careful not to damage sealed connectors with test probes.

All wiring harnesses should be replaced with identical parts, using the same gauge wire and connectors. When signal wires are spliced into a harness, use wire with high temperature insulation only. It is seldom necessary to replace a complete harness. If replacement is necessary, pay close attention to insure proper harness routing. Secure the harness with suitable plastic wire clamps to prevent vibrations from causing the harness to wear in spots or contact any hot components.

Weatherproof connectors cannot be replaced with standard connectors. Instructions are provided with replacement connector and terminal packages. Some wire harnesses have mounting indicators (usually pieces of colored tape) to mark where the harness is to be secured.

In making wiring repairs, its important that you always replace damaged wires with wires that are the same gauge as the wire being replaced. The heavier the wire, the smaller the gauge number. Wires are color-coded to aid in identification and whenever possible the same color coded wire should be used for replacement. A wire stripping and crimping tool is necessary to install solderless terminal connectors. Test all crimps by pulling on the wires; it should not be possible to pull the wires out of a good crimp.

Wires which are open, exposed or otherwise damaged are repaired by simple splicing. Where possible, if the wiring harness is accessible and the damaged place in the wire can be located, it is best to open the harness and check for all possible damage. In an inaccessible harness, the wire must be bypassed with a new insert, usually taped to the outside of the old harness.

When replacing fusible links, be sure to use fusible link wire, NOT ordinary automotive wire. Make sure the fusible segment is of the same gauge and construction as the one being replaced and double the stripped end when crimping the terminal connector for a good contact. The melted (open) fusible link segment of the wiring harness should be cut off as close to the harness as possible, then a new segment spliced in as described. In the case of a damaged fusible link that feeds two harness wires, the harness connections should be replaced with two fusible link wires so that each circuit will have its own separate protection.

Most of the problems caused in the wiring harness are due to bad ground connections. Always check all vehicle ground connections for corrosion or looseness before performing any power feed checks to eliminate the chance of a bad ground affecting the circuit.

Hard Shell Connectors

Unlike molded connectors, the terminal contacts in hard shell connectors can be replaced. Weatherproof hard-shell connectors with the leads molded into the shell have non-replaceable terminal ends. Replacement usually involves the use of a special terminal removal tool that depresses the locking tangs (barbs) on the connector terminal and allows the connector to be removed from the rear of the shell. The connector shell should be replaced if it shows any evidence of burning, melting, cracks, or breaks. Replace individual terminals that are burnt, corroded, distorted or loose.

The insulation crimp must be tight to prevent the insulation from sliding back on the wire when the wire is pulled. The insulation must be visibly compressed under the crimp tabs, and the ends of the crimp should be turned in for a firm grip on the insulation.

The wire crimp must be made with all wire strands inside the crimp. The terminal must be fully compressed on the wire strands with the ends of the crimp tabs turned in to make a firm grip on the wire. Check all connections with an ohmmeter to insure a good contact. There should be no measurable resistance between the wire and the terminal when connected.