Honda_Cr-V_2001-2006

Power Door Locks

Print

Door Lock Motor



Removal & Installation
2001 Models
  1. Remove the screw from the door handle trim, then slide the handle assembly forward and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2.  
  3. Carefully pry at the small opening on the bottom of the speaker grill, and remove the grille.
  4.  
  5. Remove the speaker mounting screws, detach the electrical connector and remove the speaker.
  6.  
  7. Remove the screws in the armrest.
  8.  
  9. Remove the center from the trim clip at the upper front of the door panel and remove the clip.
  10.  
  11. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  12.  
  13. Carefully lift the door panel up and away from the door frame.

    Click image to see an enlarged view

    Fig. Remove the screw from the door handle trim



    Click image to see an enlarged view

    Fig. Remove the screws from the arm rest supports



    Click image to see an enlarged view

    Fig. Remove the center pin from the panel clip, then remove the clip



    Click image to see an enlarged view

    Fig. Slide the handle assembly forward using 2 screwdrivers. One inserted in the housing, the other to tap lightly with



    Click image to see an enlarged view

    Fig. Once the handle slides forward, the retaining hook will release, allowing you to remove the handle



    Click image to see an enlarged view

    Fig. Push the lock rod clip to release the rod



    Click image to see an enlarged view

    Fig. Unplug the connector from the electric door lock before removing the door handle



    Click image to see an enlarged view

    Fig. Remove the speaker grille by carefully prying at the small opening at the bottom of the grill



    Click image to see an enlarged view

    Fig. Remove the speaker, then remove the door panel screws



    Click image to see an enlarged view

    Fig. Once all the fasteners are removed, use a suitable door panel trim tool to release the door panel clips . . .



    Click image to see an enlarged view

    Fig. . . . then carefully lift the door panel up and away from the door

  14.  
  15. Remove the plastic vapor barrier.
  16.  
  17. Remove the lock cylinder and outer door handle.
  18.  
  19. Remove the bolt from the rear window channel guide.
  20.  
  21. Unplug the electrical connectors, wire harness clips and inner handle rod.
  22.  
  23. Remove the latch mounting screws, using a hand impact driver if necessary.
  24.  
  25. Installation is the reverse of the removal procedure.

    Click image to see an enlarged view

    Fig. Use a hand impact driver to loosen and tighten the door lock fasteners

  26.  

  1. Remove the screw from the door handle trim, then slide the handle assembly forward and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2.  
  3. Disconnect the 3P connector, then remove the two mounting screws and driver's door lock switch.
  4.  
  5. Installation is the reverse of the removal procedure.
  6.  

2002-06 Models

NOTE
This procedure requires the use of Trim pad remover, Snap-on A 177A, or equivalent, commercially available trim removal tool and KTC trim tool set SOJATP2014, or equivalent trim tool set.


NOTE
Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.

  1. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover.

    Click image to see an enlarged view

    Fig. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover

  2.  
  3. Remove the screws.
  4.  
  5. Driver's door: Pull the inner handle (A) rearward and out half-way to release the power door lock switch bracket (B) from the door panel (C).

    Click image to see an enlarged view

    Fig. On the driver-s side door, pull the inner handle (A) rearward and out half-way to release the power door lock switch bracket (B) from the door panel (C)

  6.  
  7. Passenger's door: Pull the inner handle half-way.
  8.  
  9. Driver's door: Disconnect the power door lock switch connector (A). Disconnect the inner handle rod (B), then remove the inner handle (C).

    Click image to see an enlarged view

    Fig. Driver's door: Disconnect the power door lock switch connector (A). Disconnect the inner handle rod (B), then remove the inner handle (C)

  10.  
  11. Lower the glass fully.
  12.  
  13. Remove the screws from under the armrest.
  14.  
  15. Passenger's door: Refer to the accompanying illustration and remove the switch panel (A), as follows:
    1. 1 - Insert a flat-tip screwdriver wrapped with protective tape through a hole under the armrest, and push up the back of the panel to release the rear hook (B).
    2.  
    3. 2 - Pull out along the edge of the panel to release the hooks (C) and clip.
    4.  
    5. 3 - Disconnect the power window switch connector (D).

      Click image to see an enlarged view

      Fig. Removing the passenger-s side switch panel (A)

    6.  

  16.  
  17. Remove the mirror mount cover.
    NOTE
    Refer to the accompanying illustration for door panel removal.

  18.  
  19. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it, as follows:
    1. 1 - Release the clip (B).
    2.  
    3. 2 - Release the clips (C) that hold the door panel with a commercially available trim pad remover (D).
    4.  
    5. 3 - Starting at the rear, pull the door panel upward, then release the lock knob (E).

      Click image to see an enlarged view

      Fig. Door panel removal

    6.  

  20.  
  21. Driver's door: Disconnect the power window switch connector (A), power mirror switch connector (B), hatch glass opener switch connector (C), and detach the harness clips (D) from the back of the door panel.

    Click image to see an enlarged view

    Fig. On the driver's door, disconnect the power window switch connector (A), power mirror switch connector (B), hatch glass opener switch connector (C), and detach the harness clips (D) from the back of the door panel.

  22.  
  23. Driver's door: Push up the back of the switch panel o release the clip and hooks, then remove the panel.
  24.  
  25. Remove the two mounting screws and the door lock switch.
  26.  

To install:

  1. Install the door lock switch and secure with the two mounting screws.
  2.  
  3. Install the panel in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors are plugged in properly, and the rod is connected properly.
    4.  
    5. Push the clips into place securely.
      NOTE
      Resetting the power window control unit is required after performing the following procedures: Disconnecting the battery, Removing the No. 6 (7.5 A) and/or the No. 23 (20 A) fuses from the under-dash fuse/relay box or disconnecting the driver's door wire harness.

    6.  

  4.  
  5. Perform the power window control unit resetting procedure, as follows:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's window all the way down by holding the driver's switch firmly down; when the window reaches the bottom, hold the driver's window switch firmly down for 2 seconds.
    4.  
    5. Move the driver's window all the way up by holding the driver's switch firmly up; when the window reaches the top, hold the driver's window switch firmly up for 2 seconds.
    6.  
    7. If the window does not work in AUTO, turn the ignition switch OFF and repeat the procedure.
    8.  

  6.  
  7. Check the window and power door lock operations
  8.  


NOTE
This procedure requires the use of Trim pad remover, Snap-on A 177A, or equivalent, commercially available trim removal tool and KTC trim tool set SOJATP2014, or equivalent trim tool set.


NOTE
Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.

  1. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover.

    Click image to see an enlarged view

    Fig. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover

  2.  
  3. Remove the screws.
  4.  
  5. Driver's door: Pull the inner handle (A) rearward and out half-way to release the power door lock switch bracket (B) from the door panel (C).

    Click image to see an enlarged view

    Fig. On the driver-s side door, pull the inner handle (A) rearward and out half-way to release the power door lock switch bracket (B) from the door panel (C)

  6.  
  7. Passenger's door: Pull the inner handle half-way.
  8.  
  9. Driver's door: Disconnect the power door lock switch connector (A). Disconnect the inner handle rod (B), then remove the inner handle (C).

    Click image to see an enlarged view

    Fig. Driver's door: Disconnect the power door lock switch connector (A). Disconnect the inner handle rod (B), then remove the inner handle (C)

  10.  
  11. Lower the glass fully.
  12.  
  13. Remove the screws from under the armrest.
  14.  
  15. Passenger's door: Refer to the accompanying illustration and remove the switch panel (A), as follows:
    1. 1 - Insert a flat-tip screwdriver wrapped with protective tape through a hole under the armrest, and push up the back of the panel to release the rear hook (B).
    2.  
    3. 2 - Pull out along the edge of the panel to release the hooks (C) and clip.
    4.  
    5. 3 - Disconnect the power window switch connector (D).

      Click image to see an enlarged view

      Fig. Removing the passenger-s side switch panel (A)

    6.  

  16.  
  17. Remove the mirror mount cover.
    NOTE
    Refer to the accompanying illustration for door panel removal.

  18.  
  19. Remove the door panel (A) with as little bending as possible to avoid creasing or breaking it, as follows:
    1. 1 - Release the clip (B).
    2.  
    3. 2 - Release the clips (C) that hold the door panel with a commercially available trim pad remover (D).
    4.  
    5. 3 - Starting at the rear, pull the door panel upward, then release the lock knob (E).

      Click image to see an enlarged view

      Fig. Door panel removal

    6.  

  20.  
  21. Driver's door: Disconnect the power window switch connector (A), power mirror switch connector (B), hatch glass opener switch connector (C), and detach the harness clips (D) from the back of the door panel.

    Click image to see an enlarged view

    Fig. On the driver's door, disconnect the power window switch connector (A), power mirror switch connector (B), hatch glass opener switch connector (C), and detach the harness clips (D) from the back of the door panel.

  22.  
  23. Driver's door: Push up the back of the switch panel o release the clip and hooks, then remove the panel.
  24.  
  25. Remove the two mounting screws and the door lock switch.
  26.  

To install:

  1. Install the door lock switch and secure with the two mounting screws.
  2.  
  3. Install the panel in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors are plugged in properly, and the rod is connected properly.
    4.  
    5. Push the clips into place securely.
      NOTE
      Resetting the power window control unit is required after performing the following procedures: Disconnecting the battery, Removing the No. 6 (7.5 A) and/or the No. 23 (20 A) fuses from the under-dash fuse/relay box or disconnecting the driver's door wire harness.

    6.  

  4.  
  5. Perform the power window control unit resetting procedure, as follows:
    1. Turn the ignition switch ON (II).
    2.  
    3. Move the driver's window all the way down by holding the driver's switch firmly down; when the window reaches the bottom, hold the driver's window switch firmly down for 2 seconds.
    4.  
    5. Move the driver's window all the way up by holding the driver's switch firmly up; when the window reaches the top, hold the driver's window switch firmly up for 2 seconds.
    6.  
    7. If the window does not work in AUTO, turn the ignition switch OFF and repeat the procedure.
    8.  

  6.  
  7. Check the window and power door lock operations
  8.  

 
label.common.footer.alt.autozoneLogo