Honda_Odyssey_2001-2006

Blower Motor

Print

Removal & Installation



2001-04 Models

WARNING
Put on gloves to protect your hands. When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. Take care not to bend or scratch the trim and panels.

  1. Remove the rear side trim panel of the right side, as follows:
    1. Remove the trim as shown.
    2.  
    3. To remove the rear side trim panel, remove the speaker grille and rear speaker.
    4.  
    5. When removing the side trim panels, be sure to remove the mounting screws behind the rear speakers.
    6.  
    7. Be sure to disconnect the rear accessory socket and brake light failure sensor connectors when removing the left rear trim panel.

      Click image to see an enlarged view

      Fig. Rear side trim removal

    8.  

  2.  
  3. Remove the self-tapping screws and the rear blower motor. Remove the self-tapping screws and the rear blower resistor.
  4.  

To install:

  1. Install the motor and the resistor in the reverse order of removal.
  2.  
  3. Install the rear side trim in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Push the clips into place securely.
    4.  
    5. Apply liquid thread lock to the anchor bolts before reinstallation.
    6.  
    7. Before installing the anchor bolts, make sure there are no twists or kinks in the seat belts.
    8.  

  4.  

2005-06 Models

NOTE
This procedure requires the use of KTC trim tool set SOJATP2014, or equivalent trim tool set. When removing trim components, wear gloves and be careful not to bend or scratch the trim and panels.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the following components, as necessary:
    1. Sliding door sill trim, as needed
    2.  
    3. C-pillar trim
    4.  
    5. Sliding door opening trim, as needed
    6.  

  4.  
  5. Pull the lower anchor cover back, and remove the lower anchor bolt.
  6.  
  7. Detach the clip and release the hooks then remove the pivot cover.
  8.  
  9. Remove the lower anchor bolt.
  10.  
  11. Remove the rear trim panel (A), as follows:
    1. Remove the side bolts (B).
    2.  
    3. Pull out both side edges of the trim panel by hand to release the hooks (C) from the rear side trim panel (D).
    4.  
    5. Pull the trim panel back to detach the clips (E, F).

      Click image to see an enlarged view

      Fig. Remove the rear trim panel (A) by removing the side bolts (B), releasing the hooks (C) from the rear side trim panel (D) and pulling the trim panel back to detach the clips (E, F)

    6.  

  12.  
  13. For the driver-s side, remove the spare tire, as follows:
    1. Place a hand in each grab handle on the spare tire cover, and pull back to release the clips. Remove the spare tire cover.
    2.  
    3. Remove the spare tire mounting bolt.
    4.  
    5. Remove the spare tire.
    6.  

  14.  
  15. Remove the rear side trim panel (A), as follows:
    1. Remove the cap (B) by releasing the two hooks (C).
    2.  
    3. Remove the rear side bolt (D).
    4.  
    5. Pull out the rear upper edge of the trim panel by hand to release the hooks (E) from the D-pillar trim (F).
    6.  
    7. Pull the trim panel back by hand to detach the clips (G, H).
    8.  
    9. Disconnect the accessory socket connectors (I) and the rear entertainment system auxiliary jack connector (J).

      Click image to see an enlarged view

      Fig. Rear side trim panel (A) and related components

    10.  

  16.  
  17. Remove the rear side trim panel beverage holder, as follows:
    1. Detach the clips and release the hooks (B), then remove the rear speaker grille (C).
    2.  
    3. Remove the screws.
    4.  
    5. Slide the beverage holder forward to release the rear hooks (D).
    6.  

  18.  
  19. Disconnect the connectors (A) from the rear mode control motor and the rear blower motor (B), then remove the wire harness clips (C), the self-tapping screws and the rear blower motor.

    Click image to see an enlarged view

    Fig. Disconnect the connectors (A) from the rear mode control motor and the rear blower motor (B), then remove the wire harness clips (C), the self-tapping screws and the rear blower motor

  20.  

To install:

  1. Install the blower motor in the reverse order of removal.
  2.  
  3. Install the panel in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Make sure there are no twists or kinks in the seat belt and that it is not pinched by the side trim panel.
    4.  
    5. Push the clips and hooks into place securely.
    6.  

  4.  
  5. Connect the negative battery cable.
  6.  

 
label.common.footer.alt.autozoneLogo