Honda_Odyssey_2001-2006

Crankshaft Damper (Balancer)

Print

Removal & Installation



J35a1 And J35a4 Engines

This procedure requires the use of the following special tools, or their equivalents:



Holder handle 07JAB-001020A
 
Holder attachment, 50 mm, offset 07MAB-PY3010A
 
Socket, 19 mm 07JAA-001020A
 

  1. Note the radio security code and station presets.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Raise and safely support the vehicle.
  6.  
  7. Remove the right front wheel and tire assembly.
  8.  
  9. Remove the lower engine splash shield.
  10.  
  11. Hold the crankshaft pulley with Honda Tool Nos. 07MAB-PY3010A Holder Attachment and 07JAB-001020A Holder Handle or their equivalents, then remove the crankshaft pulley bolt by turning it in a counterclockwise direction with a 19mm socket and breaker bar.

    Click image to see an enlarged view

    Fig. Hold the pulley with holder handle (A) and holder attachment (B). Remove the bolt with a heavy duty 19 mm socket (C) and breaker bar

  12.  
  13. Remove the crankshaft pulley.
  14.  

To install:

  1. Clean the pulleys (A), crankshaft (B), bolt (C) and washer (D). Lubricate with new engine oil as shown.
    WARNING
    Never use an impact wrench to tighten the crankshaft pulley bolt.



    Click image to see an enlarged view

    Fig. Clean the pulleys (A), crankshaft (B), bolt (C) and washer (D). Lubricate with new engine oil as shown

  2.  
  3. Install the crankshaft pulley and holding the pulley with holder handle (A) and holder attachment (B), tighten the bolt to 181 ft. lbs. (245 Nm) with a torque wrench and 19mm socket.

    Click image to see an enlarged view

    Fig. Hold the pulley with holder handle (A) and holder attachment (B). Tighten the bolt with a torque wrench and 19mm socket (C)

  4.  
  5. Install the splash shield.
  6.  
  7. Install the right front tire/wheel.
  8.  
  9. Connect the negative battery cable, then enter the security code for the radio.
  10.  

J35a6 And J35a7 Engines

This procedure requires the use of the following special tools, or their equivalents:



Holder handle 07JAB-001020A
 
Holder attachment, 50 mm, offset 07MAB-PY3010A
 
Socket, 19 mm 07JAA-001020A
 

  1. Note the radio security code and station presets.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Raise and safely support the vehicle.
  6.  
  7. Remove the right front wheel and tire assembly.
  8.  
  9. Remove the lower engine splash shield.
  10.  
  11. Remove the accessory drive belt, as outlined in this section.
  12.  
  13. Hold the crankshaft pulley with Honda Tool Nos. 07MAB-PY3010A Holder Attachment and 07JAB-001020A Holder Handle or their equivalents, then remove the crankshaft pulley bolt by turning it in a counterclockwise direction with a 19mm socket and breaker bar.

    Click image to see an enlarged view

    Fig. Hold the pulley with holder handle (A) and holder attachment (B). Remove the bolt with a heavy duty 19mm socket (C) and breaker bar

  14.  
  15. Remove the crankshaft pulley.
  16.  

To install:

  1. Clean the pulleys (A), crankshaft (B), bolt (C) and washer (D). Lubricate with new engine oil as shown.
    WARNING
    Never use an impact wrench to tighten the crankshaft pulley bolt.



    Click image to see an enlarged view

    Fig. Clean the pulleys (A), crankshaft (B), bolt (C) and washer (D). Lubricate with new engine oil as shown

  2.  
  3. Install the crankshaft pulley, then tighten the bolt, as follows:
    1. Hold the pulley with the holder handle (A) and holder attachment (B), then tighten the bolt to 47 ft. lbs. (65 Nm) with a torque wrench and heavy duty 19mm socket (C).
    2.  
    3. Mark the bolt head (D) and crankshaft pulley (E) as shown, then tighten the bolt an additional 60° (The mark on the bolt head should line up with the mark on the crankshaft pulley).

      Click image to see an enlarged view

      Fig. Hold the pulley with the holder handle (A) and holder attachment (B), then tighten the bolt to 47 ft. lbs. (65 Nm) with a torque wrench and heavy duty 19mm socket (C)



      Click image to see an enlarged view

      Fig. Mark the bolt head (D) and crankshaft pulley (E) as shown, then tighten the bolt an additional 60 degrees. The mark on the bolt head should line up with the mark on the crankshaft pulley

    4.  

  4.  
  5. Install the drive belt, as outlined in this section.
  6.  
  7. Install the splash shield.
  8.  
  9. Install the right front tire/wheel.
  10.  
  11. Connect the negative battery cable, then enter the security code for the radio.
  12.  

 
label.common.footer.alt.autozoneLogo