Honda_Odyssey_2001-2006

Side Mirrors

Print

Manual Mirror



Removal & Installation
2001-04 Models
  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand as shown in the accompanying figure.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand

  4.  
  5. Remove the bolts securing the mirror. While holding the mirror (A), push out the clip (B), and remove the mirror. Be careful not to scratch the door.
  6.  
  7. Install the manual mirror in the reverse order of removal, and push the cover clip into place securely.

    Click image to see an enlarged view

    Fig. Remove the bolts securing the mirror. While holding the mirror (A), push out the clip (B), and remove the mirror

  8.  

2005-06 Models

NOTE
There were no manual side mirrors on 2005-06 Odyssey models.

Power Mirror



Removal & Installation
2001-04 Models

NOTE
This procedure covers the replacement of the door lock actuator (motor) and requires the use of Trim pad remover, Snap-on A177A, or equivalent, commercially available trim pad removal tool.

  1. Remove the mirror mount cover, as follows:
    1. Lower the door glass fully.
    2.  
    3. Carefully pry out the mirror mount cover by hand.

      Click image to see an enlarged view

      Fig. Carefully pry out the mirror mount cover (A) by hand

    4.  

  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the inner handle, as follows, being careful not to scratch the door panel:
    1. Pry out the cap and remove the screw.
    2.  
    3. Pull the inner handle forward and out halfway.
    4.  
    5. Disconnect the inner handle rod and power door lock switch connector (if equipped).

      Click image to see an enlarged view

      Fig. Pry out the cap (B) to remove the screw, pull the inner handle forward and out halfway. Detach the inner handle rod (D) and door lock connector (D), if equipped

    6.  

  6.  
  7. Detach the clips and hooks, then remove the speaker grille. Remove the screws.
  8.  
  9. Remove the pull pocket panel (A), as follows, being careful not to scratch the door panel:
    1. Pry out the cap and remove the screw.
    2.  
    3. Release the hook and detach the power window switch connectors.
    4.  

  10.  
  11. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Disconnect the speaker connector (C).
  12.  
  13. On 2002-04 models equipped with seat heaters, disconnect the seat heater switch subharness connector.
    NOTE
    Remove the door panel with as little bending as possible to avoid creasing or breaking it.



    Click image to see an enlarged view

    Fig. Trim panel removal tool (B)



    Click image to see an enlarged view

    Fig. Driver-s side door panel removal & installation

  14.  
  15. Disconnect the connector (A), and detach the harness clip (B), then remove the bolts securing the mirror. While holding the mirror (C), push out the clip (D), and remove the mirror. Be careful not to scratch the door.

    Click image to see an enlarged view

    Fig. Disconnect the connector (A), and detach the harness clip (B), then remove the bolts securing the mirror. While holding the mirror (C), push out the clip (D), and remove the mirror

  16.  

To install:

  1. Install the power mirror in the reverse order of removal, and note these items:
    1. Make sure the connector is plugged in properly.
    2.  
    3. Attach the harness clip.
    4.  
    5. Push the cover clip into place securely.
    6.  

  2.  
  3. Install the door panel in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Push the clips into place securely.
    4.  
    5. Make sure the connectors are plugged in properly, and the inner handle rod is connected properly.
    6.  

  4.  
  5. For 2003-04 models, reset the power window control unit, as follows:
    1. Turn the ignition switch off, then back ON (II).
    2.  
    3. Move the driver's window all the way down by holding the driver's switch to the AUTO DOWN position; when the window reaches the bottom, hold the driver's window switch in the AUTO DOWN position for 2 seconds.
    4.  
    5. Move the driver's window all the way up without stopping by holding the driver's switch to the AUTO UP position; when the window reaches the top, hold the driver's window switch in the AUTO UP position for 2 seconds.
    6.  
    7. If the window does not work in AUTO, reset the power window control unit according to the above procedures again.
    8.  

  6.  
  7. On 2002-04 models, if equipped with seat heaters, check for proper operation.
  8.  
  9. Check the window and power door lock operations.
  10.  

2005-06 Models
  1. Lower the door glass fully.
  2.  
  3. With your hand, carefully release the clip, lift the cover upward to release the hook (A), and remove the cover (B) in the sequence shown.

    Click image to see an enlarged view

    Fig. With your hand, carefully release the clip, lift the cover upward to release the hook (A), and remove the cover (B) in the sequence shown

  4.  
  5. Disconnect the connector (A).
  6.  
  7. While holding the mirror, remove the nuts securing the mirror.

    Click image to see an enlarged view

    Fig. Power mirror connector (A) and retainer tightening specifications

  8.  
  9. While holding the mirror, push in on the connector clips (A), then push out to remove the mirror (B). Be careful not to scratch the door.

    Click image to see an enlarged view

    Fig. While holding the mirror, push in on the connector clips (A), then push out to remove the mirror (B). Take care not to scratch the door.

  10.  
  11. Install the mirror in the reverse order of removal, and make sure the connector is plugged in properly. Tighten the retainers to the specifications shown in the accompanying figure.
  12.  

 
label.common.footer.alt.autozoneLogo