Honda_Odyssey_2001-2006

2005-06 Models

Print

With The Hds



  1. Make sure you have the anti-theft codes for the radio and the navigation system (if equipped) then write down the radio station and XM radio channel presets.
  2.  
  3. Remove the fuel fill cap, and relieve the pressure in the fuel tank.
  4.  
  5. Turn the ignition switch ON (II).
  6.  
  7. From the INSPECTION MENU of the HDS, select Fuel Pump OFF, then start the engine and let it idle until it stalls.
  8.  
  9. Turn the ignition switch OFF.
    NOTE
    Do not allow the engine to idle above 1,000 rpm or the PCM will continue to operate the fuel pump. A DTC or a Temporary DTC may be set during this procedure. Check for DTCs, and clear them as needed.

  10.  
  11. Turn the ignition switch OFF.
  12.  
  13. Disconnect the negative cable from the battery.

    Click image to see an enlarged view

    Fig. Remove the quick-connect fitting cover (A)

  14.  
  15. Remove the quick-connect fitting cover (A).
  16.  
  17. Check the fuel quick-connect fitting for dirt, and clean it if needed
  18.  
  19. Place a rag or shop towel over the quick-connect fitting (A).

    Click image to see an enlarged view

    Fig. Quick-connect fitting

  20.  
  21. Disconnect the quick-connect fitting (A): Hold the connector (B) with one hand, and squeeze the retainer tabs (C) with the other hand to release them from the locking tabs (D). Pull the connector off.
    NOTE
    Be careful not to damage the line (E) or other parts. Do not use tools. If the connector does not move, keep the retainer tabs pressed down, and alternately pull and push the connector until it comes off easily. Do not remove the retainer from the line; once removed, the retainer must be replaced with a new one.

  22.  
  23. After disconnecting the quick-connect fitting, check it for dirt or damage. Reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and the navigation system, then enter the customer's radio station and XM radio channel presets. Set the clock.
  24.  

Without The Hds



  1. Make sure you have the anti-theft codes for the radio and the navigation system (if equipped) then write down the radio station and XM radio channel presets.

    Click image to see an enlarged view

    Fig. Remove the left kick panel, then remove PGM-Fl main relay 2 (FUEL PUMP) (A) from the driver's under-dash fuse/relay box

  2.  
  3. Remove the left kick panel, then remove PGM-Fl main relay 2 (FUEL PUMP) (A) from the driver's under-dash fuse/relay box.
  4.  
  5. Start the engine, and let it idle until it stalls.
    NOTE
    If any DTCs are stored, clear and ignore them.

  6.  
  7. Turn the ignition switch OFF.
  8.  
  9. Remove the fuel fill cap.
  10.  
  11. Disconnect the negative cable from the battery.
  12.  
  13. Remove the quick-connect fitting cover (A).
  14.  
  15. Check the fuel quick-connect fitting for dirt, and clean it if needed.
  16.  
  17. Place a rag or shop towel over the quick-connect fitting (A).
  18.  
  19. Disconnect the quick-connect fitting (A): Hold the connector (B) with one hand, and squeeze the retainer tabs (C) with the other hand to release them from the locking tabs (D). Pull the connector off.
    NOTE
    Be careful not to damage the line (E) or other parts. Do not use tools. If the connector does not move, keep the retainer tabs pressed down, and alternately pull and push the connector until it comes off easily. Do not remove the retainer from the line; once removed, the retainer must be replaced with a new one.

  20.  
  21. After disconnecting the quick-connect fitting, check it for dirt or damage.
  22.  
  23. Reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and the navigation system, then enter the customer's radio station and XM radio channel presets. Set the clock.
  24.  

 
label.common.footer.alt.autozoneLogo