Honda_Passport_1997-2002

Power Windows

Print

Window Motor & Regulator



Removal & Installation
Front Window
  1. Disconnect the negative battery cable.
  2.  
  3. Remove power window switch/regulator handle as follows:
    1. Power windows: Pry out the power window switch and remove the connectors.
    2.  
    3. Manual windows: To remove the regulator handle (1), remove the clip (2), at the root of the handle by using wire with hook.

      Click image to see an enlarged view

      Fig. To remove the regulator handle (1), remove the clip (2), at the root of the handle by using wire with hook

    4.  

  4.  
  5. Remove the screw while pulling the inside lever toward you and then remove the inside handle
  6.  
  7. Remove speaker grille, as follows:
    1. Pull out the front side of the grille.
    2.  

  8.  
  9. Remove 4 screws and disconnect the speaker harness connector, then remove the speaker.
  10.  
  11. Remove courtesy light lens.
  12.  
  13. Remove the door mirror cover.
  14.  
  15. Remove the grip cover.
  16.  
  17. Remove 5 screws (1), (3) and pull out the door trim panel at the 6 clip (2) positions.

    Click image to see an enlarged view

    Fig. Remove 5 screws (1), (3) and pull out the door trim panel at the 6 clip (2) positions.

  18.  
  19. Note the location of the door harness, peel the waterproof sheet off the door panel carefully.
  20.  
  21. Remove the 2 screws through the access hole and pull out the glass upward.
  22.  
  23. Remove the window regulator, by disconnecting the window regulator motor harness connector, if equipped with power windows.
  24.  
  25. Remove the glass run by pulling the glass run out from the door frame groove.
  26.  
  27. Remove the power window motor, by removing the 3 screws then removing the motor.
  28.  

To install:

  1. To install, follow the removal steps in the reverse order, noting the following points:
    1. Apply chassis grease to the lock assembly and striker moving surface.
    2.  
    3. Install the regulator handle as shown in the illustration, if equipped without power windows.

      Click image to see an enlarged view

      Fig. If equipped with manual windows, install the regulator handle as shown

    4.  
    5. Check to see that the window regulator operates smoothly and the glass opens and closes properly.
    6.  
    7. Install the waterproof sheet tightly against the door panel.
    8.  

  2.  

Rear Window
  1. Disconnect the negative battery cable.
  2.  
  3. Remove rear corner garnish.
  4.  
  5. Remove window regulator handle, by removing the clip on the rear side of the regulator handle using a wire.
  6.  
  7. Remove the screw while pulling the inside lever toward you and then remove the inside handle.
  8.  
  9. Remove the screw(s) from the pull case and courtesy light. Remove the rear corner garnish.
  10.  
  11. Pull out the trim panel at the 8 clip positions. Disconnect the power window switch connector.

    Click image to see an enlarged view

    Fig. Pull out the trim panel at the 8 clip positions. Disconnect the power window switch connector and courtesy light connector

  12.  
  13. Remove power window switch, if equipped.
  14.  
  15. Remove bracket.
  16.  
  17. Note the location of the door harness, peel the waterproof sheet off the door panel carefully.
  18.  
  19. Remove the speaker bracket mounting screws and bracket.
  20.  
  21. Remove the fixed glass, as follows:
    1. Remove the bolt and screw, then pull it upward.
    2.  
    3. Align the height of regulator to the access hole. Remove 2 screws attaching bottom channel and regulator, then remove the glass.
    4.  
    5. Remove the window glass by tilting it as necessary.
    6.  

  22.  
  23. Remove the window regulator fixing bolts and pull the regulator out from the lower hole of the door panel.
  24.  
  25. Pull the glass run out from the door frame.
  26.  
  27. Remove the power window motor screws, then remove the motor.
  28.  

To install:

  1. To install, follow the removal steps in the reverse order, noting the following points:
    1. Apply chassis grease to the lock assembly and striker moving surface.
    2.  
    3. Install the regulator handle as shown in the illustration, if equipped without power windows.

      Click image to see an enlarged view

      Fig. If equipped with manual windows, install the regulator handle as shown

    4.  
    5. Check to see that the window regulator operates smoothly and the glass opens and closes properly.
    6.  
    7. Install the waterproof sheet tightly against the door panel.
    8.  

  2.  

Window Switch Control Panel



Removal & Installation
Front Door
  1. Disconnect the negative battery cable.
  2.  
  3. Pull out the switch by pushing the spring with the tip of a screwdriver.
  4.  
  5. Disconnect the connector, then remove the switch.
  6.  
  7. Installation is the reverse of the removal procedure.
  8.  

Rear Door
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the rear door trim pad.
  4.  
  5. Disconnect the rear power window switch connector.
  6.  
  7. Remove the rear power window switch mount screw from the back side of the rear door trim, then remove the switch.
  8.  
  9. Installation is the reverse of the removal procedure.
  10.  

 
label.common.footer.alt.autozoneLogo