Honda Pilot - 2003-2005

Blower Motor

Print

Removal & Installation



  1. Disconnect the negative battery cable.
  2.  
  3. Remove the center console, as follows:
    NOTE
    When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts to prevent damage. Take care not to scratch the front seat, dashboard, and related parts.

    1. Starting at the top, gently pull the center front covers (A) out to detach the clips (B), then pull the cover out to detach the remaining clips (C), and remove the covers from both sides.

      Click image to see an enlarged view

      Fig. Starting at the top, gently pull the center front covers (A) out to detach the clips (B), then pull the cover out to detach the remaining clips (C), and remove the covers from both sides

    2.  
    3. To remove the center lower cover (A), remove the coin pocket (B), screws (C), then pull out the cover to detach the clips (D) and detach the accessory power socket connector (E) and console light connector (F).

      Click image to see an enlarged view

      Fig. Center lower cover (A) removal and installation

    4.  
    5. If equipped, remove the center lower cover (A) with the seat heater switches by removing the screws (B), pull the cover out to detach the clips (C), then disconnect the accessory power socket connector (D), seat heater switch connectors (E) and console light connector (F).

      Click image to see an enlarged view

      Fig. If equipped, remove the center lower cover (A) with the seat heater switches by removing the screws (B), pull the cover out to detach the clips (C), then disconnect the accessory power socket connector (D), seat heater switch connectors (E) and console light connector (F)

    6.  
    7. Detach the clips and release the hooks (A), then remove the driver's console side trim (B) and passenger's console side trim (C).

      Click image to see an enlarged view

      Fig. Detach the clips and release the hooks (A), then remove the driver's console side trim (B) and passenger's console side trim (C)

    8.  
    9. Starting at the top, gently pull out the console rear trim (A) to detach the clips (B), then pull out the trim to detach the remaining clips (C), and disconnect the rear heater-A/C passenger's control panel-unit connectors (D) and accessory power socket connector (E). If equipped with rear entertainment system, disconnect the rear entertainment system jack connector (F).

      Click image to see an enlarged view

      Fig. Starting at the top, gently pull out the console rear trim (A) to detach the clips (B), then pull out the trim to detach the remaining clips (C), and disconnect the rear heater-A/C passenger's control panel-unit connectors (D) and accessory power socket connector (E). If equipped with rear entertainment system, disconnect the rear entertainment system jack connector (F)

    10.  
    11. From both sides of the center console, remove the bolts (B) and screws (C). Remove the center console (A). Detach the harness clip (D). Disconnect the Disconnect the accessory power socket connector (E), and detach it. Lift the console (A) up, then remove it.

      Click image to see an enlarged view

      Fig. Console removal and installation

    12.  

  4.  
  5. Disconnect the 2P connector (A) from the rear blower motor (B), then remove the self-tapping screws and the cover (C). Turn the rear blower motor clockwise to the stop, and remove it.
  6.  
  7. Install the motor in the reverse order of removal.

    Click image to see an enlarged view

    Fig. Disconnect the 2P connector (A) from the rear blower motor (B), then remove the self-tapping screws and the cover (C). Turn the rear blower motor clockwise to the stop, and remove it

  8.  
  9. Install the center console in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Make sure all the connectors are plugged in properly.
    4.  
    5. Push the clips into place securely.
    6.  

  10.  
  11. Connect the negative battery cable.
  12.  

 
label.common.footer.alt.autozoneLogo