Honda Prelude Accord Civic S2000 2001-2006

Side Mirrors (1 of 3)

Print

Manual Mirror



Removal & Installation
Accord
2001-02 Models
  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown

  4.  
  5. Remove the bolts securing the mirror.

    Click image to see an enlarged view

    Fig. Remove the 3 mirror mounting bolts

  6.  
  7. While holding the mirror, push out the clip (A), and remove the mirror. Take care not to scratch the door.

    Click image to see an enlarged view

    Fig. While holding the mirror, push out the clip (A), and remove the mirror. Take care not to scratch the door

  8.  
  9. Installation is the reverse of the removal procedure.
  10.  

2003-06 Models
  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown-sedan shown, coupe similar

  4.  
  5. While holding the mirror, remove the nuts securing the mirror, and remove the mirror.
  6.  
  7. Install the mirror in the reverse order of removal.
  8.  

Civic
2-Door Models

NOTE
This procedure requires the use of KTC trim tool set SOJATP2014 and Trim pad remover, Snap-on A 177A or equivalent, commercially available trim panel removal tools.


NOTE
Use the appropriate tool from the KTC trim tool set to avoid damage when prying components.

  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Mirror mount cover removal-2-door Civic

  4.  
  5. If equipped with manual windows: remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C).

    Click image to see an enlarged view

    Fig. If equipped with manual windows: remove the regulator handle (A) by pulling the clip (B) out with a wire hook (C)

  6.  
  7. Remove the inner handle (A), being careful not to scratch the door panel, as follows:
    1. Pry out on the upper portion of the cover (B) to release the hooks (C, D), then remove the cover.
    2.  
    3. Remove the screws
    4.  
    5. Pull the inner handle forward and out half-way to release the hook (E).
    6.  
    7. Disconnect the inner handle rod (F) and power door lock switch connector (G) (driver's side for some models).

      Click image to see an enlarged view

      Fig. Door inner handle removal and installation

    8.  

  8.  
  9. Remove the switch panel (A) (power window model) or the pull pocket (B) (manual window model), as follows:
    1. Using a trim tool, pry the cap (C), then remove the screw (D).
    2.  
    3. Pry out the panel or pocket to release the clips (E).
    4.  
    5. Release the clip (F) by pulling the cover or pocket forward.
    6.  
    7. Power window model: Disconnect the power window switch connector (G).

      Click image to see an enlarged view

      Fig. Exploded view of the switch panel (power windows) or pull pocket (manual windows)

    8.  

  10.  
  11. Remove the screws (H) securing the door panel.
  12.  
  13. Release the clips that hold the door panel (A) with a commercially available trim pad remover (B), then remove the door panel by pulling it upward. Remove the door panel with as little bending as possible to avoid creasing or breaking it.

    Click image to see an enlarged view

    Fig. Door panel removal and installation

  14.  
  15. If equipped with a tweeter, pull the plastic cover (A) back as necessary, and disconnect the connector (B), then remove the mirror mount cover (C) with the tweeter.
  16.  
  17. While holding the mirror, remove the nuts securing the mirror, and remove the mirror (manual mirror model).
  18.  

To install:

  1. Install the mirror in the reverse order of removal.
  2.  
  3. Install the door panel in the reverse order of removal, and note these items:
    1. Replace any damaged clips.
    2.  
    3. Make sure the connectors are plugged in properly, and the rod is connected properly.
    4.  
    5. Make sure the window and power door locks operate properly.
    6.  
    7. If equipped with manual windows, install the regulator handle so it points forward and up at a 45° angle with the glass fully closed.

      Click image to see an enlarged view

      Fig. If equipped with manual windows, install the regulator handle so it points forward and up at a 45° angle with the glass fully closed

    8.  

  4.  

4-Door Models
  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Mirror mount cover removal-4-door Civic

  4.  
  5. While holding the mirror, remove the nuts securing the mirror, and remove the mirror (manual mirror model).
  6.  
  7. Install the mirror in the reverse order of removal.
  8.  

Prelude
  1. Lower the door glass fully.
  2.  
  3. Carefully pry out the mirror mount cover (A) by hand in the sequence shown.

    Click image to see an enlarged view

    Fig. Carefully pry out the mirror mount cover (A) by hand in the sequence shown

  4.  
  5. Remove the bolts securing the mirror.

    Click image to see an enlarged view

    Fig. Remove the 3 mirror mounting bolts

  6.  
  7. While holding the mirror, push out the clip (A), and remove the mirror. Take care not to scratch the door.

    Click image to see an enlarged view

    Fig. While holding the mirror, push out the clip (A), and remove the mirror. Take care not to scratch the door

  8.  
  9. Installation is the reverse of the removal procedure.
  10.  

 
label.common.footer.alt.autozoneLogo