Hyundai Car 1999-05

2.0L L4 VIN F Std 3

Print

Trouble Code: P0457



EVAP System Leak (Fuel Tank Cap) Detected

Possible Causes:



Canister vent (CV) solenoid may be stuck in open position
 
EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube disconnected or cracked, or canister is damaged
 
Fuel filler cap missing, loose (not tightened) or the wrong part
 
Fuel tank pressure (FTP) sensor has failed (mechanical fault)
 
Fuel tank control valve is contaminated, damaged or has failed
 

Trouble Code: P0500



VSS Signal (ABS/TCS Rough Road Signal) Fault

Possible Causes:



VSS signal circuit is open, shorted to ground or system power
 
VSS (Hall) power circuit is open (check Fuse 5 in fuse panel)
 
VSS (Hall) ground circuit is open
 
VSS (Hall) is damaged or has failed
 
PCM has failed
 

Trouble Code: P0501



Vehicle Speed Sensor Circuit Performance

Possible Causes:



VSS signal circuit from the sensor to the I/P Cluster to the PCM is open, shorted to ground or to system power
 
VSS (Magnetic) signal (+) or (-) circuit is open or shorted
 
VSS (Magnetic) is damaged or has failed
 
PCM has failed
 

Trouble Code: P0506



Idle Speed Lower Than Expected

Possible Causes:



ISC motor "open" circuit is open or shorted to ground
 
ISC motor "close" circuit is open or shorted to ground
 
ISC motor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0507



Idle Speed Higher Than Expected

Possible Causes:



ISC motor control circuit(s) open or shorted to ground
 
ISC motor is damaged or has failed
 
PCM is damaged
 

Trouble Code: P0560



Battery Backup Circuit Malfunction

Possible Causes:



Battery backup circuit is open (check the fuse to the battery)
 
Battery terminals are corroded, dirty or loose
 
Battery has been removed or the cables were disconnected
 
PCM has failed
 
TSB 00-36-013 (12/00) contains information about this code
 

Trouble Code: P0562



System Voltage Low Input

Possible Causes:



Ignition system voltage circuit is open
 
Generator is damaged or has failed (generator output too low)
 
PCM has failed
 

Trouble Code: P0563



System Voltage High Input

Possible Causes:



Generator is damaged or has failed (generator output to high)
 
PCM has failed
 

Trouble Code: P0601



PCM (Internal Controller) Checksum Error

Possible Causes:



Clear the trouble codes and retest for this trouble code. If the same trouble code resets, the PCM has failed and must be replaced to repair this problem.
 

Trouble Code: P0605



PCM (Internal Controller) ROM Error

Possible Causes:



Clear the trouble codes and retest for this trouble code. If the same trouble code resets, the PCM has failed and must be replaced to repair this problem.
 

Trouble Code: P0700



Transmission Control System Signal

Possible Causes:



Clear the trouble codes and retest for this trouble code. If the same trouble code resets, the TCM may have failed.
 

Trouble Code: P1100



MAP Sensor Performance

Possible Causes:



MAP sensor signal circuit is open or shorted to ground
 
MAP sensor vacuum source line is clogged or contains ice
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1102



MAP Sensor Circuit Low Input

Possible Causes:



MAP sensor signal circuit is open or shorted to ground
 
MAP sensor power (VREF) circuit is open
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1103



MAP Sensor Circuit High Input

Possible Causes:



MAP sensor signal circuit is shorted to VREF or system power
 
MAP sensor ground circuit is open
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P01134



HO2S-11 (Bank 1 Sensor 1) Transition Time Switch

Possible Causes:



HO2S signal circuit is open or shorted to ground
 
HO2S element is contaminated or it has failed
 
HO2S heater is damaged or has failed
 
Intake air leaks, exhaust manifold leaks or PCV system leaks
 
MAF sensor out of calibration (it may be dirty or contaminated)
 

Trouble Code: P01154



HO2S-21 (Bank 2 Sensor 1) Transition Time Switch

Possible Causes:



HO2S signal circuit is open or shorted to ground
 
HO2S element is contaminated or it has failed
 
HO2S heater is damaged or has failed
 
Intake air leaks, exhaust manifold leaks or PCV system leaks
 
MAF sensor out of calibration (it may be dirty or contaminated)
 

Trouble Code: P01166



HO2S-11 Controller Adaptive Test (Bank 1)

Possible Causes:



Air leaks after the MAF sensor, or in the EGR or PCV system
 
Base engine "mechanical" fault affecting one or more cylinders
 
Exhaust leaks located in front of the A/FS or HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too little fuel during cruise or idle periods (e.g., faulty fuel pump or dirty, restricted fuel filter)
 
Fuel injector (one or more) dirty or pressure regulator has failed
 
HO2S is contaminated, deteriorated or it has failed
 
Vehicle driven low on fuel or until it ran out of fuel
 

Trouble Code: P01372



PCM Segment Time Acquisition Incorrect

Possible Causes:



Target wheel in the crankshaft installed incorrectly
 
CKP sensor signal erratic or invalid
 
CKP sensor signal circuit open or grounded (intermittent fault)
 

Trouble Code: P01510



Idle Speed Control Actuator Opening Coil Circuit Shorted

Possible Causes:



Idle speed actuator opening coil circuit shorted to system power (B+)
 
Idle speed actuator is damaged or has failed
 
PCM has failed
 

Trouble Code: P01513



Idle Speed Control Actuator Opening Coil Circuit Open

Possible Causes:



Idle speed actuator opening coil circuit open or shorted to ground
 
Idle speed actuator is damaged or has failed
 
PCM has failed
 

Trouble Code: P01521



Power Steering Switch Input Circuit Malfunction

Possible Causes:



Power steering pressure switch circuit open, shorted to ground, shorted to VREF, or shorted to system power (B+)
 
Power steering pressure switch is damaged or has failed
 
PCM has failed
 

Trouble Code: P01529



Customer Snapshot Request Error

Possible Causes:



Transmission control module error
 
Check for trouble codes in the transmission control module
 
TSB 1-40-005 (3/01) contains information about this code
 

Trouble Code: P01552



Idle Speed Control Actuator Closing Coil Circuit Shorted

Possible Causes:



Idle speed actuator closing coil circuit shorted to system power
 
Idle speed actuator is damaged or has failed
 
PCM has failed
 

Trouble Code: P01553



Idle Speed Control Actuator Closing Coil Circuit Open

Possible Causes:



Idle speed actuator closing coil circuit is open or shorted to ground
 
Idle speed actuator is damaged or has failed
 
PCM has failed
 

Trouble Code: P01586



Encoding Signal Circuit Not Rational

Possible Causes:



P/N switch signal circuit is open or shorted to ground
 
P/N switch signal circuit is shorted to system power
 
P/N switch is damaged or has failed
 
PCM has failed
 

Trouble Code: P01602



Serial Communication Problem With The TCM

Possible Causes:



CAN network circuit open or shorted to ground
 
CAN network circuit shorted to VREF or system power (B+)
 
TCM has failed
 

Trouble Code: P01605



Rough Road Sensor Circuit Malfunction

Possible Causes:



Acceleration sensor circuit is open or shorted to ground
 
Acceleration sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P01606



Rough Road Sensor Circuit Not Valid

Possible Causes:



Acceleration sensor circuit is open or shorted to ground
 
Acceleration sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P01613



MIL Request Signal Circuit High Input

Possible Causes:



MIL request circuit between the PCM and TCM is shorted to system power
 

Trouble Code: P01624



Cooling Fan Relay Low Circuit

Possible Causes:



Cooling Fan Relay control circuit open or shorted to ground
 
Cooling Fan Relay power circuit from Main Relay is open
 
Cooling Fan Relay is damaged or has failed
 
PCM has failed
 
TSB 00-36-013 (9/00) contains information about this code
 

Trouble Code: P01625



Cooling Fan Relay High Circuit Malfunction

Possible Causes:



Cooling Fan Relay control circuit shorted to system power (B+)
 
Cooling Fan Relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P0105



Manifold Absolute Pressure Sensor Circuit Malfunction

Possible Causes:



MAP sensor signal circuit is open or shorted to ground
 
MAP sensor ground circuit open between sensor and ground
 
MAP sensor power (VREF) circuit is open
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P0120



Throttle Position Sensor Circuit Malfunction

Possible Causes:



TP sensor signal circuit is open or shorted to ground
 
TP sensor ground circuit or power (VREF) circuit is open
 
TP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1123



Fuel Trim Adaptive Air System Too Rich

Possible Causes:



Base engine "mechanical" fault affecting one or more cylinders
 
EVAP system component has failed or canister fuel saturated
 
Exhaust leaks located in front of the HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too much fuel during cruise or idle periods (e.g., faulty fuel pump, or faulty pressure regulator)
 
Fuel injector(s) is leaking or stuck partially open (one or more)
 
HO2S is contaminated, deteriorated or it has failed
 

Trouble Code: P1124



Fuel Trim Adaptive Air System Too Lean

Possible Causes:



Air leaks after the MAF sensor, or in the EGR or PCV system
 
Base engine "mechanical" fault affecting one or more cylinders
 
Exhaust leaks located in front of the HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too little fuel during cruise or idle periods (e.g., faulty fuel pump or dirty, restricted fuel filter)
 
Fuel injector (one or more) dirty or pressure regulator has failed
 
HO2S is contaminated, deteriorated or it has failed
 
Vehicle driven low on fuel or until it ran out of fuel
 

Trouble Code: P1127



Long Term Fuel Trim Multiplier System Too Rich

Possible Causes:



Base engine "mechanical" fault affecting one or more cylinders
 
EVAP system component has failed or canister fuel saturated
 
Exhaust leaks located in front of the HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too much fuel during cruise or idle periods (e.g., faulty fuel pump, or faulty pressure regulator)
 
Fuel injector(s) is leaking or stuck partially open (one or more)
 
HO2S is contaminated, deteriorated or it has failed
 

Trouble Code: P1128



Long Term Fuel Trim Multiplier System Too Lean

Possible Causes:



Air leaks after the MAF sensor, or in the EGR or PCV system
 
Base engine "mechanical" fault affecting one or more cylinders
 
Exhaust leaks located in front of the HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too little fuel during cruise or idle periods (e.g., faulty fuel pump or dirty, restricted fuel filter)
 
Fuel injector (one or more) dirty or pressure regulator has failed
 
HO2S is contaminated, deteriorated or it has failed
 
Vehicle driven low on fuel or until it ran out of fuel
 

 
label.common.footer.alt.autozoneLogo