Hyundai Cars 2006-2008

Removal & Installation

Print

Specific to:

Hyundai Entourage 2007-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative (-) battery terminal.
  4.  
  5. Remove the center air vent.
  6.  
  7. Remove the 4 fastening screws from the control panel.
  8.  
  9. Move the heater and A/C control panel (A) out from dash board enough to view connections.
  10.  
  11. Disconnect the electrical connections (A) from the control panel.

    Click image to see an enlarged view

    Fig. Remove the heater and A/C control panel (A)



    Click image to see an enlarged view

    Fig. Disconnect the electrical connections (A) from the control panel

  12.  
  13. Remove the heater & A/C control panel.
  14.  

To install:

  1. Installation is the reverse of the removal procedure.

    Click image to see an enlarged view

    Fig. Control panel-front and rear view



    Click image to see an enlarged view

    Fig. Control panel connector pin function

  2.  

Specific to:

Hyundai Accent 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery terminal.
  4.  
  5. Disconnect the clips of the center fascia lower panel and pull to remove it using a screw driver.
    WARNING
    Avoid damaging the retaining clips.



    Click image to see an enlarged view

    Fig. Removing the control panel-Accent

  6.  
  7. Disconnect the connectors (A) from the center fascia.

    Click image to see an enlarged view

    Fig. Disconnect the connectors (A) from the center fascia-Accent

  8.  
  9. Remove the heater and A/C controller (A) after loosening 4 screws.

    Click image to see an enlarged view

    Fig. Remove the heater and A/C controller (A) after loosening 4 screws-Accent

  10.  
  11. Installation is the reverse order of removal.
    NOTE
    Make sure all the connectors are plugged in properly.

  12.  

Specific to:

Hyundai Azera 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery terminal.
  4.  
  5. Remove the crash pad center garnish (A).

    Click image to see an enlarged view

    Fig. Remove the crash pad center garnish (A)-Azera

  6.  
  7. Remove the crash pad side cover (B).

    Click image to see an enlarged view

    Fig. Remove the crash pad side cover (B)-Azera

  8.  
  9. Remove the screws and remove the lower panel (A).

    Click image to see an enlarged view

    Fig. Remove the screws and remove the lower panel (A)-Azera

  10.  
  11. Remove the center fascia panel (A) and then disconnect the connectors.

    Click image to see an enlarged view

    Fig. Remove the center fascia panel (A)-Azera

  12.  
  13. Remove the 4 screws and remove the heater and A/C controller (A).

    Click image to see an enlarged view

    Fig. Remove the 4 screws and remove the heater and A/C controller (A)-Azera

  14.  
  15. Installation is the reverse order of removal.
    NOTE
    Make sure all the connectors are plugged in properly.

  16.  

Specific to:

Hyundai Elantra 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery terminal.
  4.  
  5. Disconnect the mounting clip and remove the center fascia panel (A).

    Click image to see an enlarged view

    Fig. Disconnect the mounting clip and remove the center fascia panel (A)-Elantra

  6.  
  7. Remove the mounting screw and remove the center fascia lower panel (A).

    Click image to see an enlarged view

    Fig. Remove the mounting screw and remove the center fascia lower panel (A)-Elantra

  8.  
  9. Remove the 4 screws and remove the heater and A/C controller (A).

    Click image to see an enlarged view

    Fig. Remove the 4 screws and remove the heater and A/C controller (A)-Elantra

  10.  
  11. Disconnect the connectors (A) from the center fascia.

    Click image to see an enlarged view

    Fig. Disconnect the connectors (A) from the center fascia-Elantra

  12.  
  13. Installation is the reverse order of removal.
    NOTE
    Make sure all the connectors are plugged in properly.

  14.  

Specific to:

Hyundai Tiburon 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery terminal.
  4.  
  5. Remove the center fascia panel (A).
    1. Remove the screw.
    2.  
    3. Pull out center fascia panel using a screw driver.
      NOTE
      Take care not to damage the fixing clips.



      Click image to see an enlarged view

      Fig. Remove the center fascia panel (A)-Tiburon

    4.  

  6.  
  7. Disconnect the connectors (B) from the center fascia.

    Click image to see an enlarged view

    Fig. Disconnect the connectors (B) from the center fascia-Tiburon

  8.  
  9. Remove the 4 screws and remove the heater and A/C controller (A).

    Click image to see an enlarged view

    Fig. Remove the 4 screws and remove the heater and A/C controller (A)-Tiburon

  10.  
  11. Installation is the reverse order of removal.
    NOTE
    Make sure all the connectors are plugged in properly.

  12.  

 
label.common.footer.alt.autozoneLogo