Hyundai Cars 2006-2008

2.7L V6 VIN F Std 6

Print

Trouble Code: P0600



CAN Communication Bus

Possible Causes:



Open or short in CAN line
 
Contact resistance in connectors
 
Faulty PCM
 

Trouble Code: P0601



PCM (Internal Controller) Checksum Error

Possible Causes:



Clear the trouble codes and retest for this trouble code. If the same trouble code resets, the PCM has failed and must be replaced to repair this problem.
 

Trouble Code: P0605



PCM (Internal Controller) ROM Error

Possible Causes:



Clear the trouble codes and retest for this trouble code. If the same trouble code resets, the PCM has failed and must be replaced to repair this problem.
 

Trouble Code: P0630



VIN Not Programmed Or Incompatible- ECM/PCMECM

Possible Causes:



PCM is new and has not yet been programmed
 

Trouble Code: P0650



Malfunction Indicator Lamp (MIL) Control Circuit

Possible Causes:



Open or short between MIL and PCM
 
Contact resistance in connectors
 
Burned out MIL bulb
 

Trouble Code: P0700



Transmission Control System Signal

Possible Causes:



Clear the trouble codes and retest for this trouble code. If the same trouble code resets, the TCM may have failed.
 

Trouble Code: P1100



MAP Sensor Performance

Possible Causes:



MAP sensor signal circuit is open or shorted to ground
 
MAP sensor vacuum source line is clogged or contains ice
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1102



MAP Sensor Circuit Low Input

Possible Causes:



MAP sensor signal circuit is open or shorted to ground
 
MAP sensor power (VREF) circuit is open
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1103



MAP Sensor Circuit High Input

Possible Causes:



MAP sensor signal circuit is shorted to VREF or system power
 
MAP sensor ground circuit is open
 
MAP sensor is damaged or has failed
 
PCM has failed
 

Trouble Code: P1134



HO2S-11 (Bank 1 Sensor 1) Transition Time Switch

Possible Causes:



HO2S signal circuit is open or shorted to ground
 
HO2S element is contaminated or it has failed
 
HO2S heater is damaged or has failed
 
Intake air leaks, exhaust manifold leaks or PCV system leaks
 
MAF sensor out of calibration (it may be dirty or contaminated)
 

Trouble Code: P1154



HO2S-21 (Bank 2 Sensor 1) Transition Time Switch

Possible Causes:



HO2S signal circuit is open or shorted to ground
 
HO2S element is contaminated or it has failed
 
HO2S heater is damaged or has failed
 
Intake air leaks, exhaust manifold leaks or PCV system leaks
 
MAF sensor out of calibration (it may be dirty or contaminated)
 

Trouble Code: P1166



HO2S-11 Controller Adaptive Test (Bank 1)

Possible Causes:



Air leaks after the MAF sensor, or in the EGR or PCV system
 
Base engine "mechanical" fault affecting one or more cylinders
 
Exhaust leaks located in front of the A/FS or HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too little fuel during cruise or idle periods (e.g., faulty fuel pump or dirty, restricted fuel filter)
 
Fuel injector (one or more) dirty or pressure regulator has failed
 
HO2S is contaminated, deteriorated or it has failed
 
Vehicle driven low on fuel or until it ran out of fuel
 

Trouble Code: P1167



HO2S-11 Controller Adaptive Test (Bank 2)

Possible Causes:



Air leaks after the MAF sensor, or in the EGR or PCV system
 
Base engine "mechanical" fault affecting one or more cylinders
 
Exhaust leaks located in front of the A/FS or HO2S location
 
Fuel control sensor is out of calibration (i.e., ECT, IAT or MAP)
 
Fuel delivery system supplying too little fuel during cruise or idle periods (e.g., faulty fuel pump or dirty, restricted fuel filter)
 
Fuel injector (one or more) dirty or pressure regulator has failed
 
HO2S is contaminated, deteriorated or it has failed
 
Vehicle driven low on fuel or until it ran out of fuel
 

Trouble Code: P1372



PCM Segment Time Acquisition Incorrect

Possible Causes:



Target wheel in the crankshaft installed incorrectly
 
CKP sensor signal erratic or invalid
 
CKP sensor signal circuit open or grounded (intermittent fault)
 

Trouble Code: P1505



Idle Charge Actuator Signal Low of Coil #1

Possible Causes:



Open or short to ground in harness
 
Contact resistance in connectors
 
Faulty ICA valve
 

Trouble Code: P1506



Idle Charge Actuator Signal High of Coil #1

Possible Causes:



Short to battery in harness
 
Contact resistance in connectors
 
Faulty ICA valve
 

Trouble Code: P1507



Idle Charge Actuator Signal Low of Coil #2

Possible Causes:



Open or short to ground in harness
 
Contact resistance in connectors
 
Faulty ICA valve
 

Trouble Code: P1508



Idle Charge Actuator Signal High of Coil #2

Possible Causes:



Short to battery in harness
 
Contact resistance in connectors
 
Faulty ICA valve
 

Trouble Code: P1521



Power Steering Switch Input Circuit Malfunction

Possible Causes:



Power steering pressure switch circuit open, shorted to ground, shorted to VREF, or shorted to system power (B+)
 
Power steering pressure switch is damaged or has failed
 
PCM has failed
 

Trouble Code: P1529



Customer Snapshot Request Error

Possible Causes:



Transmission control module error
 
Check for trouble codes in the transmission control module
 
TSB 1-40-005 (3/01) contains information about this code
 

Trouble Code: P1586



Encoding Signal Circuit Not Rational

Possible Causes:



P/N switch signal circuit is open or shorted to ground
 
P/N switch signal circuit is shorted to system power
 
P/N switch is damaged or has failed
 
PCM has failed
 

Trouble Code: P1602



Serial Communication Problem With The TCM

Possible Causes:



CAN network circuit open or shorted to ground
 
CAN network circuit shorted to VREF or system power (B+)
 
TCM has failed
 

Trouble Code: P1613



MIL Request Signal Circuit High Input

Possible Causes:



MIL request circuit between the PCM and TCM is shorted to system power
 

Trouble Code: P1624



Cooling Fan Relay Low Circuit

Possible Causes:



Cooling Fan Relay control circuit open or shorted to ground
 
Cooling Fan Relay power circuit from Main Relay is open
 
Cooling Fan Relay is damaged or has failed
 
PCM has failed
 
TSB 00-36-013 (9/00) contains information about this code
 

Trouble Code: P1625



Cooling Fan Relay High Circuit Malfunction

Possible Causes:



Cooling Fan Relay control circuit shorted to system power (B+)
 
Cooling Fan Relay is damaged or has failed
 
PCM has failed
 

Trouble Code: P1690



SMARTRA Error

Possible Causes:



Open or short in antenna or SMARTRA circuit
 
Antenna
 
SMARTRA
 
Faulty transponder
 
Faulty ECM
 

Trouble Code: P1691



Antenna Error

Possible Causes:



Open or short in antenna or SMARTRA circuit
 
Antenna
 
SMARTRA
 
Faulty transponder
 
Faulty ECM
 

Trouble Code: P1692



Immobilizer Lamp Error

Possible Causes:



Short Circuit in immobilizer lamp circuit.
 
Open/Short in control harness
 
Faulty PCM/ECM
 

Trouble Code: P1693



Transponder No Response Error/Invalid Response

Possible Causes:



Invalid transponder.
 
 

Trouble Code: P1694



ECM Signal Error

Possible Causes:



Open or short in antenna or SMARTRA circuit
 
Antenna
 
SMARTRA
 
Faulty transponder
 
Faulty ECM
 

Trouble Code: P1695



EEPROM Error

Possible Causes:



Open or short in antenna or SMARTRA circuit
 
Antenna
 
SMARTRA
 
Faulty transponder
 
Faulty ECM
 

Trouble Code: P1696



Authentication Fail

Possible Causes:



Invalid transponder.
 
 

 
label.common.footer.alt.autozoneLogo