Hyundai Cars 2006-2008

Camshaft, Bearings & Lifters

Print

Bearing Replacement



Specific to:

Hyundai Accent 2006-2008

Hyundai Azera 2006-2008

Hyundai Elantra 2006-2008

Hyundai Entourage 2007-2008

Hyundai Sonata 2006-2008

Hyundai Tiburon 2006-2008

Check each bearing for damage. If the bearing surface is excessively damaged, replace the cylinder head assembly or camshaft bearing cap, as necessary.

Inspection



Specific to:

Hyundai Entourage 2007-2008

  1. Inspect the cam lobes.
    1. Using a micrometer, measure the cam lobe height.
    2.  
    3. If the cam lobe height is less than specified, replace the camshaft.
    4.  

  2.  
  3. Inspect the camshaft journal clearance.
    1. Clean the bearing caps and camshaft journals.
    2.  
    3. Place the camshafts on the cylinder head.
    4.  
    5. Lay a strip of Plastigage®across each of the camshaft journal.
    6.  
    7. Install the bearing caps and tighten the bolts with specified torque.
      NOTE
      Do not turn the camshaft.

    8.  
    9. Remove the bearing caps.
    10.  
    11. Measure the Plastigage®at its widest point.
    12.  
    13. If the oil clearance is greater than specified, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.
    14.  
    15. Completely remove the Plastigage®.
    16.  
    17. Remove the camshafts.
    18.  

  4.  
  5. Inspect the camshaft end play.
    1. Install the camshafts.
    2.  
    3. Using a dial indicator, measure the end play while moving the camshaft back and forth.
    4.  
    5. If the end play is greater than specified, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.
    6.  
    7. Remove the camshafts.
    8.  

  6.  
  7. Inspect the Continuous Variable Valve Timing (CVVT) assembly.
    1. Check that the CVVT assembly will not turn.
    2.  
    3. Apply vinyl tape to all the parts except the one indicated by the arrow in the illustration.

      Click image to see an enlarged view

      Fig. Apply vinyl tape to the CVVT on all parts except the one indicated by the arrow

    4.  
    5. Wrap tape around the tip of the air gun and apply air of approx. 14 psi to the port of the camshaft. Perform this in order to release the lock pin for the maximum delay angle locking.
      NOTE
      Wrap a shop rag around the CVVT as the oil may spray out when the air pressure is applied.

    6.  
    7. Under the condition of air pressure being applied, turn the CVVT assembly to the advance angle side with your hand.

      Depending on the air pressure, the CVVT assembly will turn to the advance side
       
      If air is leaking from the port and air pressure cannot be maintained, the locking pin will not release
       

    8.  

  8.  
  9. Except the position where the lock pin meets at the maximum delay angle, let the CVVT assembly turn back and forth and check the movable range and that there is no disturbance.
    1. The CVVT should move smoothly in the range of about 20°.
    2.  
    3. Turn the CVVT assembly with your hand and lock it at the maximum delay angle position.
    4.  

  10.  
  11. Inspect the Hydraulic Lash Adjuster (HLA).
    1. With the HLA filled with engine oil, hold A and press B by hand.
    2.  
    3. If B moves, replace the HLA.

      Click image to see an enlarged view

      Fig. With the HLA filled with engine oil, hold A and press B by hand

    4.  

  12.  

Specific to:

Hyundai Accent 2006-2008

Hyundai Azera 2006-2008

Hyundai Elantra 2006-2008

Hyundai Sonata 2006-2008

Hyundai Tiburon 2006-2008

  1. Inspect the cam lobes.
    1. Using a micrometer, measure the cam lobe height.
    2.  
    3. If the cam lobe height is less than specified, replace the camshaft.
    4.  

  2.  
  3. Inspect the camshaft journal clearance.
    1. Clean the bearing caps and camshaft journals.
    2.  
    3. Place the camshafts on the cylinder head.
    4.  
    5. Lay a strip of Plastigage across each of the camshaft journal.
    6.  
    7. Install the bearing caps and tighten the bolts with specified torque.
      NOTE
      Do not turn the camshaft.

    8.  
    9. Remove the bearing caps.
    10.  
    11. Measure the Plastigage at its widest point.
    12.  
    13. If the oil clearance is greater than specified, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.
    14.  
    15. Completely remove the Plastigage.
    16.  
    17. Remove the camshafts.
    18.  

  4.  
  5. Inspect the camshaft end play.
    1. Install the camshafts.
    2.  
    3. Using a dial indicator, measure the end play while moving the camshaft back and forth.
    4.  
    5. If the end play is greater than specified, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.
    6.  
    7. Remove the camshafts.
    8.  

  6.  
  7. Inspect the Continuous Variable Valve Timing (CVVT) assembly.
    1. Check that the CVVT assembly will not turn.
    2.  
    3. Apply vinyl tape to all the parts except the one indicated by the arrow in the illustration.

      Click image to see an enlarged view

      Fig. Apply vinyl tape to the CVVT on all parts except the one indicated by the arrow

    4.  
    5. Wrap tape around the tip of the air gun and apply air of approx. 14 psi to the port of the camshaft. Perform this in order to release the lock pin for the maximum delay angle locking.
      NOTE
      Wrap a shop rag around the CVVT as the oil may spray out when the air pressure is applied.

    6.  
    7. Under the condition of air pressure being applied, turn the CVVT assembly to the advance angle side with your hand.

      Depending on the air pressure, the CVVT assembly will turn to the advance side
       
      If air is leaking from the port and air pressure cannot be maintained, the locking pin will not release
       

    8.  

  8.  
  9. Except the position where the lock pin meets at the maximum delay angle, let the CVVT assembly turn back and forth and check the movable range and that there is no disturbance.
    1. The CVVT should move smoothly in the range of about 20°.
    2.  
    3. Turn the CVVT assembly with your hand and lock it at the maximum delay angle position.
    4.  

  10.  
  11. Inspect the Hydraulic Lash Adjuster (HLA).
    1. With the HLA filled with engine oil, hold A and press B by hand.
    2.  
    3. If B moves, replace the HLA.

      Click image to see an enlarged view

      Fig. With the HLA filled with engine oil, hold A and press B by hand

    4.  

  12.  

Removal & Installation



Specific to:

Hyundai Entourage 2007-2008

Use fender covers to avoid damaging painted surfaces. To avoid damage, unplug the wiring connectors carefully while holding the connector portion. Mark all wiring and hoses to avoid misconnection. Inspect the timing belt before removing. Turn the crankshaft pulley so that the No. 1 piston is at Top Dead Center (TDC).

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    The negative battery connection
     
    The timing chain
     
    The water temperature control assembly
     
    The camshaft bearing cap
     
    The camshaft assembly

    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and engine block



    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and related components

     

  4.  

To install:

Thoroughly clean all parts to be assembled. Rotate the crankshaft, set the No. 1 piston at TDC.

  1. Install the Continuously Variable Valve Timing (CVVT) and camshaft sprocket. Tightening torque: 48-56 ft. lbs. (65-76 Nm).
    1. Install camshaft-inlet to dowel pin of CVVT assembly. At this time, do not install to oil hole of camshaft-inlet.
    2.  
    3. Hold the hexagonal head wrench portion of the camshaft with a vise, and install the bolt and CVVT assembly.
    4.  
    5. Do not rotate the CVVT assembly when the camshaft is installed to the dowel pin of the CVVT assembly.
    6.  

  2.  
  3. Install the camshafts.
    1. Apply a light coat of engine oil on camshaft journals.
    2.  
    3. Assemble the key groove of camshaft rear side to the same level of head top surface.
    4.  
    5. Be careful to get the right bank, left bank, intake side, and exhaust side in the correct position before assembling.
    6.  

  4.  
  5. Install the camshaft bearing caps in the sequence shown:
    1. Step 1-Tightening torque: 48 inch lbs. (6 Nm).
    2.  
    3. Step 2-Tightening torque: 84-108 inch lbs. (10-12 Nm).
      WARNING
      Be careful to properly position the right bank, left bank, intake side, exhaust side, and front mark on the camshaft bearing caps while assembling.


      WARNING
      Rotate the crankshaft so as not to contact the valves to the pistons by positioning the pistons 0.3937 inch (10mm) below the top of the cylinder block.



      Click image to see an enlarged view

      Fig. Install the camshaft bearing caps in the sequence shown



      Click image to see an enlarged view

      Fig. Be careful to properly position the camshaft bearing caps according to its markings

    4.  

  6.  
  7. Install the water temperature control assembly.
  8.  
  9. Install the timing chain.
  10.  
  11. Check and adjust the valve clearance, as necessary.
  12.  
  13. Connect the negative battery cable.
  14.  
  15. Fill with engine coolant.
  16.  
  17. Start the engine and check for leaks.
  18.  
  19. Recheck the engine coolant level and oil level.
  20.  

1.6L & 2.0L Engines

Specific to:

Hyundai Accent 2006-2008

Hyundai Elantra 2006-2008

Hyundai Tiburon 2006-2008

Engine removal is not required for this procedure. Use a fender cover to avoid damaging painted surfaces. To avoid damage, unplug the wiring connectors carefully while holding the connector portion. Mark all wiring and hoses to avoid misconnection. Inspect the timing belt before removal. Turn the crankshaft pulley so that the No. 1 piston is at Top Dead Center (TDC).

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the terminals from battery and remove the battery.
  4.  
  5. Remove the engine cover.
  6.  
  7. Remove the undercover.
  8.  
  9. Drain the engine coolant. Remove the radiator cap to speed draining.
  10.  
  11. Remove the intake air hose and air cleaner assembly:
    1. Disconnect the breather hose from intake air hose.
    2.  
    3. Remove the intake air hose and air cleaner upper cover.
    4.  
    5. Disconnect the ECM connectors.
    6.  
    7. Remove the air cleaner element and air cleaner lower cover.
    8.  

  12.  
  13. Remove the battery tray.
  14.  
  15. Remove the upper radiator hose and lower radiator hose.
  16.  
  17. Remove the heater hoses.
  18.  
  19. Remove the fuel hose.
  20.  
  21. Remove the accelerator cable by loosening the lock-nut, then slip the cable end out of the throttle linkage.
  22.  
  23. Disconnect the Throttle Position Sensor (TPS) connector and the MAP sensor connector.
  24.  
  25. Remove the engine wire harness connectors and wire harness clamps from cylinder head and the intake manifold:
    1. Disconnect the rear oxygen sensor connector.
    2.  
    3. Disconnect the air conditioner compressor switch connector.
    4.  
    5. Disconnect the knock sensor connector.
    6.  
    7. Disconnect the injector connectors.
    8.  
    9. Remove the wire harness bracket.
    10.  
    11. Disconnect the Idle Speed Actuator (ISA) connector.
    12.  
    13. Disconnect the front oxygen sensor connector.
    14.  
    15. Disconnect the Crankshaft Position Sensor (CKP) connector.
    16.  
    17. Disconnect the Oil Control Valve (OCV) connector.
    18.  
    19. Disconnect the ignition coil connector.
    20.  
    21. Disconnect the ignition coil condenser connector.
    22.  
    23. Disconnect the Camshaft Position Sensor (CMP) connector.
    24.  
    25. Disconnect the ground cable.
    26.  
    27. Remove the wire harness bracket.
    28.  

  26.  
  27. Remove or disconnect the following:

    The hose of the Purge Control Solenoid Valve (PCSV) side
     
    The brake booster vacuum hose
     
    The power steering pump and fix the pump to vehicle with a wire
     
    The ignition coil
     
    The exhaust manifold
     
    The intake manifold
     
    The timing belt
     
    The cylinder head cover
     
    The camshaft sprocket
     
    The timing chain auto tensioner
     
    The camshaft bearing caps and camshafts

    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and engine block-1.6L engine



    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and related components-1.6L engine



    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and related components-2.0L engine

     

  28.  

To install:

Thoroughly clean all parts to be assembled. Rotate the crankshaft, set the No. 1 piston at TDC.

  1. Install the camshafts:
    1. Align the camshaft timing chain with the intake timing chain sprocket and exhaust timing chain sprocket as shown.

      Click image to see an enlarged view

      Fig. Align the camshaft timing chain with the intake timing chain sprocket and exhaust timing chain sprocket-1.6L engine

    2.  
    3. Install the camshaft and bearing caps.

      1.6L engine-Tightening torque: 108-120 inch lbs. (12-14 Nm).
       
      2.0L engine-Tightening torque: 120-132 inch lbs. (14-15 Nm)
       

    4.  
    5. Install the timing chain auto tensioner. Tightening torque: 72-84 inch lbs. (8-10 Nm).
    6.  

  2.  
  3. Using the SST (09221 - 21000), install the camshaft bearing oil seal.
  4.  
  5. Install the camshaft sprocket.
  6.  
  7. Install the cylinder head cover.
    1. Install the cylinder head cover gasket in the groove of the cylinder head cover.
      NOTE
      Before installing the cylinder head cover gasket, thoroughly clean the cylinder head cover and the groove. When installing, make sure the cylinder head cover gasket is seated securely in the corners of the recesses with no gap.

    2.  
    3. Apply liquid gasket to the head cover gasket at the corners of the recess.
      NOTE
      Use liquid gasket, Loctite® No. 5999. Check that the mating surfaces are clean and dry before applying liquid gasket. After assembly, wait at least 30 minutes before filling the engine with oil.

    4.  
    5. Install the cylinder head cover with bolts.

      Step 1: Pre-tighten all bolts by 36-48 inch lbs. (4-5 Nm)
       
      Step 2: Tighten by the specified torque 72-84 inch lbs. (8-10 Nm)
       

    6.  

  8.  
  9. Install or connect the following:

    The timing belt
     
    The intake manifold
     
    The exhaust manifold
     
    The ignition coil
     
    The power steering pump
     
    The brake booster hose
     
    The hose of the PCSV side
     

  10.  
  11. Install the engine wire harness connectors and wire harness clamps to the cylinder head and the intake manifold:

    The wire harness bracket
     
    The ground cable
     
    The CMP(Camshaft position sensor) connector
     
    The ignition coil condenser connector
     
    The ignition coil connector
     
    The OCV connector
     
    The CKP connector
     
    The front oxygen sensor connector
     
    The ISA connector
     
    The wire harness bracket
     
    The fuel injector connectors
     
    The knock sensor connector
     
    The air conditioner compressor switch connector
     
    The rear oxygen sensor connector
     

  12.  
  13. Install or connect the following:

    The TPS connector and the MAP sensor connector
     
    The accelerator cable
     
    The fuel hose
     
    The heater hoses
     
    The upper radiator hose and lower radiator hose
     
    The battery tray
     
    The intake air hose and air cleaner assembly
     

  14.  
  15. Install the air cleaner element and air cleaner lower cover. Tightening torque: 72-84 inch lbs. (8-10 Nm).
  16.  
  17. Connect the ECM connectors.
  18.  
  19. Install the intake air hose and air cleaner upper cover.
  20.  
  21. Connect the breather hose to intake air hose.
  22.  
  23. Install the undercover.
  24.  
  25. Install the engine cover. Tightening torque: 36-48 inch lbs. (4-6 Nm).
  26.  
  27. Install the battery and connect the battery terminals.
  28.  
  29. Fill with engine coolant.
  30.  
  31. Start the engine and check for leaks.
  32.  
  33. Recheck engine coolant level and oil level.
  34.  

2.7L Engine

Specific to:

Hyundai Tiburon 2006-2008

Engine removal is not required for this procedure. Use a fender cover to avoid damaging painted surfaces. To avoid damage, unplug the wiring connectors carefully while holding the connector portion. Mark all wiring and hoses to avoid misconnection. Inspect the timing belt before removing. Turn the crankshaft pulley so that the No. 1 piston is at Top Dead Center (TDC).

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove the side cover (A, B, C) and the engine cover (D).
  4.  
  5. Disconnect the battery terminal and the battery.

    Click image to see an enlarged view

    Fig. Remove the side cover and engine cover-2.7L engine

  6.  
  7. Remove the radiator drain plug and drain engine coolant. Remove the radiator cap to speed draining.
  8.  
  9. Remove the air cleaner assembly.
    1. Disconnect the Air Flow Sensor (AFS) connector.
    2.  
    3. Remove the breather hose from intake hose.
    4.  
    5. Remove the intake hose and air cleaner upper cover.
    6.  
    7. Remove the air cleaner lower cover.
    8.  

  10.  
  11. Remove the upper radiator hose and lower radiator hose.
  12.  
  13. Remove the heater hoses.
  14.  
  15. Remove the engine wire harness connectors and wire harness clamps from the cylinder head and the intake manifold:

    Throttle position sensor (TPS) connector
     
    Idle speed actuator (ISA) connector
     
    Purge Control Solenoid Valve (PCSV) connector
     
    Knock sensor connector
     
    Camshaft Position (CMP) sensor connector
     
    Engine ground line
     
    Heated oxygen sensor (Bank 2, Sensor 1) connector
     
    Engine temperature coolant sensor connector
     
    Ignition coil connector
     
    Crankshaft Position (CKP) sensor connector
     
    Heated oxygen sensor (Bank 1, Sensor 2) connector
     
    Fuel injector connectors
     

  16.  
  17. Remove or disconnect the following:

    The fuel inlet from the delivery pipe
     
    The Purge Control Solenoid Valve (PCSV) hose
     
    The brake booster vacuum hose
     
    The accelerator cable by loosening the locknut, then slip the cable end out of the throttle linkage
     
    The auto-cruise connector and the auto-cruise cable
     
    The PCV hose
     
    The power steering pump
     
    The timing belt
     
    The cylinder head covers
     
    The camshaft sprocket
     
    The camshaft bearing caps
     
    The camshafts

    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and engine block-2.7L engine



    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and related components-2.7L engine

     

  18.  

To install:

Thoroughly clean all parts to be assembled. Rotate the crankshaft, set the No. 1 piston at TDC.

  1. Install the camshafts.
    1. Align the camshaft timing chain with the intake timing chain sprocket and exhaust timing chain sprocket as shown.
    2.  
    3. Install the camshaft.
    4.  
    5. Install the camshaft bearing caps.
      NOTE
      Apply new engine oil to the thrust portion and journal of the camshafts. Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.



      Tightening torque: M6 (38mm) bolt: 7-9 ft. lbs. (10-13 Nm)
       
      Tightening torque: M6 (50mm) bolt: 11-12 ft. lbs. (15-17 Nm)
       



      Click image to see an enlarged view

      Fig. Align the camshaft timing chain with the intake timing chain sprocket and exhaust timing chain sprocket as shown-2.7L engine

    6.  

  2.  
  3. Using the SST (09214-21000), install the camshaft bearing oil seal.
  4.  
  5. Install the camshaft sprocket.
    1. Temporarily install the camshaft sprocket bolts.
    2.  
    3. Hold the hexagonal head wrench portion of the camshaft with a wrench, and tighten the camshaft sprocket bolts. Tightening torque of camshaft sprocket bolt: 65-80 ft. lbs. (88-108 Nm).
    4.  

  6.  
  7. Install the semi-circular packing.
  8.  
  9. Install the cylinder head cover.
    1. Install the cylinder head cover gasket in the groove of the cylinder head cover.
      NOTE
      Before installing the head cover gasket, thoroughly clean the head cover gasket and the groove. When installing, make sure the head cover gasket is seated securely in the corners of the recesses with no gap.

    2.  
    3. Apply liquid gasket to the head cover gasket at the corners of the recess. Use liquid gasket, Loctite® No. 5699. Check that the mating surfaces are clean and dry before applying liquid gasket. After assembly, wait at least 30 minutes before filling the engine with oil.
    4.  
    5. Install the cylinder head covers with the 16 bolts. Uniformly tighten the bolts in several passes. Tightening torque: 6-7 ft. lbs. (8-10 Nm).
    6.  

  10.  
  11. Install or connect the following:

    The timing belt
     
    The power steering pump
     
    The PCV hose
     
    The auto-cruise connector and the auto- cruise cable
     
    The accelerator cable by loosening the locknut, then slip the cable end out of the throttle linkage
     
    The brake booster vacuum hose
     
    The PCSV hose
     
    The fuel inlet from delivery pipe
     
    The fuel injector connectors
     
    Heated oxygen sensor (Bank 1, Sensor 2) connector
     
    Crankshaft position sensor connector
     
    Ignition coil connector
     
    Engine temperature coolant sensor connector
     
    Heated oxygen sensor (Bank 2, Sensor 1) connector
     
    Engine ground line
     
    Camshaft position sensor connector
     
    Knock sensor connector
     
    Injector connector
     
    The PCSV connector
     
    Idle speed actuator connector
     
    Throttle position sensor connector
     

  12.  
  13. Install the engine wire harness connectors and wire harness clamps to the cylinder head and the intake manifold.
  14.  
  15. Install the heater hoses.
  16.  
  17. Install the upper radiator hose and lower radiator hose.
  18.  
  19. Install the air cleaner assembly.
    1. Install the air cleaner lower cover.
    2.  
    3. Install the intake hose and air cleaner upper cover.
    4.  
    5. Install the breather hose from intake hose.
    6.  
    7. Connect the AFS connector.
    8.  

  20.  
  21. Connect the battery terminal and the battery.
  22.  
  23. Fill with engine coolant.
  24.  
  25. Install the side cover and the engine cover.
  26.  
  27. Start the engine and check for leaks.
  28.  
  29. Recheck the engine coolant level and oil level.
  30.  

3.3L & 3.8L Engines

Specific to:

Hyundai Azera 2006-2008

Hyundai Sonata 2006-2008

Use a fender cover to avoid damaging painted surfaces. To avoid damage, unplug the wiring connectors carefully while holding the connector portion. Mark all wiring and hoses to avoid misconnection. Inspect the timing belt before removing. Turn the crankshaft pulley so that the No. 1 piston is at Top Dead Center (TDC).

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    The negative battery connection
     
    The timing chain
     
    The water temperature control assembly
     
    The camshaft bearing cap
     
    The camshaft assembly

    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and engine block-3.3L and 3.8L engines



    Click image to see an enlarged view

    Fig. Exploded view of cylinder head and related components-3.3L and 3.8L engines

     

  4.  

To install:

  1. Thoroughly clean all parts to be assembled. Rotate the crankshaft, set the No. 1 piston at TDC.
  2.  
  3. Install the Continuously Variable Valve Timing (CVVT) and camshaft sprocket. Tightening torque: 48-56 ft. lbs. (65-76 Nm).
    1. Install camshaft-inlet to dowel pin of CVVT assembly. At this time, do not install to oil hole of camshaft-inlet.
    2.  
    3. Hold the hexagonal head wrench portion of the camshaft with a vise, and install the bolt and CVVT assembly.
    4.  
    5. Do not rotate the CVVT assembly when the camshaft is installed to the dowel pin of the CVVT assembly.
    6.  

  4.  
  5. Install the camshafts.
    1. Apply a light coat of engine oil on camshaft journals.
    2.  
    3. Assemble the key groove of camshaft rear side to the same level of head top surface.
    4.  
    5. Be careful to get the right bank, left bank, intake side, and exhaust side in the correct position before assembling.
    6.  

  6.  
  7. Install the camshaft bearing caps in the sequence shown:
    1. Step 1-Tightening torque: 48 inch lbs. (6 Nm).
    2.  
    3. Step 2-Tightening torque: 84-108 inch lbs. (10-12 Nm).
      WARNING
      Be careful to properly position the right bank, left bank, intake side, exhaust side, and front mark on the camshaft bearing caps while assembling.


      WARNING
      Rotate the crankshaft so as not to contact the valves to the pistons by positioning the pistons 0.3937 inch (10mm) below the top of the cylinder block.



      Click image to see an enlarged view

      Fig. Install the camshaft bearing caps in the sequence shown-3.3L and 3.8L engines



      Click image to see an enlarged view

      Fig. Be careful to properly position the camshaft bearing caps according to its markings-3.3L and 3.8L engines

    4.  

  8.  
  9. Install the water temperature control assembly.
  10.  
  11. Install the timing chain.
  12.  
  13. Check and adjust the valve clearance, as necessary.
  14.  
  15. Connect the negative battery cable.
  16.  
  17. Fill with engine coolant.
  18.  
  19. Start the engine and check for leaks.
  20.  
  21. Recheck the engine coolant level and oil level.
  22.  

 
label.common.footer.alt.autozoneLogo