Hyundai Cars 2006-2008

Locks & Lock Systems 2

Print

Power Door Locks



Removal & Installation
Door Lock Motor

Specific to:

Hyundai Entourage 2007-2008


WARNING
Be careful not to scratch the door trim and other parts. Wear gloves to protect your hands.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the quadrant inner cover.

    Click image to see an enlarged view

    Fig. Remove the quadrant inner cover (A)

  6.  
  7. Loosen the mounting screw, remove the inside handle cover.

    Click image to see an enlarged view

    Fig. Loosen the mounting screw, then remove the inside handle cover (A)

  8.  
  9. Loosen the door trim (C) mounting screws.
  10.  
  11. Release the clips that hold the door trim, then remove the door trim by pulling it upward.
  12.  
  13. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D).

    Click image to see an enlarged view

    Fig. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim and remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D)

  14.  
  15. Remove the door glass as follows:
    1. Remove the door trim seal.

      Click image to see an enlarged view

      Fig. Remove the door trim seal (A)

    2.  
    3. Carefully move the glass (A) until you can see the bolts, then loosen them.
    4.  
    5. Carefully pull the glass out through the window slot (B).

      Click image to see an enlarged view

      Fig. Carefully move the glass (A) until you can see the bolts, then loosen them. Carefully pull the glass out through the window slot (B)

    6.  

  16.  
  17. Detach the wiring harness.

    Click image to see an enlarged view

    Fig. Detach the wiring harness (A)

  18.  
  19. Detach the lock rod (A) and outside handle rod (B).

    Click image to see an enlarged view

    Fig. Detach the lock rod (A) and outside handle rod (B).

  20.  
  21. Loosen the door module mounting bolts, then remove the door module (A).

    Click image to see an enlarged view

    Fig. Loosen the door module mounting bolts, then remove the door module (A)

  22.  
  23. Installation is the reverse of the removal procedure. Note the following:
    1. Roll the glass up and down to make sure it moves freely and without binding.
    2.  
    3. Make sure there is no clearance between the glass and glass run channel when the glass is closed.
    4.  
    5. Adjust the position of the glass if necessary.
    6.  

  24.  

Front

Specific to:

Hyundai Accent 2006-2008

Hyundai Azera 2006-2008

Hyundai Elantra 2006-2008

Hyundai Sonata 2006-2008

Hyundai Tiburon 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove the front door trim.
  4.  
  5. Disconnect the wiring harness (A).

    Click image to see an enlarged view

    Fig. Front door lock wiring harness

  6.  
  7. Disconnect the lock rod (A) and outside handle rod (B).
  8.  
  9. Remove the door lock module (C).

    Click image to see an enlarged view

    Fig. Front door lock module

  10.  
  11. Installation is the reverse of removal.
  12.  
  13. Make sure the connectors are plugged in properly and each cable is connected securely.
  14.  
  15. Check the door locks for proper operation.
  16.  
  17. Roll the glass up and down to check for free movement without any binding.
  18.  

Rear

Specific to:

Hyundai Accent 2006-2008

Hyundai Azera 2006-2008

Hyundai Elantra 2006-2008

Hyundai Sonata 2006-2008

Hyundai Tiburon 2006-2008

  1. Remove the door trim.
  2.  
  3. Disconnect the power window motor connector (A), speaker connector (B), and actuator connector (C).
  4.  
  5. Detach the harness clip.

    Click image to see an enlarged view

    Fig. Rear door wiring harness

  6.  
  7. Remove the rear door lock module assembly (A).

    Click image to see an enlarged view

    Fig. Rear door lock module

  8.  
  9. Installation is the reverse of removal.
  10.  
  11. Make sure the connectors are plugged in properly and each cable is connected securely.
  12.  
  13. Check the door locks for proper operation.
  14.  
  15. Roll the glass up and down to check for free movement without any binding.
  16.  

Door Lock Switch

Specific to:

Hyundai Entourage 2007-2008


WARNING
Be careful not to scratch the door trim and other parts. Wear gloves to protect your hands.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the quadrant inner cover.

    Click image to see an enlarged view

    Fig. Remove the quadrant inner cover (A)

  6.  
  7. Loosen the mounting screw, remove the inside handle cover.

    Click image to see an enlarged view

    Fig. Loosen the mounting screw, then remove the inside handle cover (A)

  8.  
  9. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D).

    Click image to see an enlarged view

    Fig. Loosen the door trim (C) mounting screws. Release the clips that hold the door trim, then remove the door trim by pulling it upward. Disconnect the power window switch connector (A), power mirror connector (B), and door courtesy lamp connector (D)

  10.  
  11. Loosen the mounting screws, then detach the connector (A).

    Click image to see an enlarged view

    Fig. Loosen the mounting screws, then detach the connector (A)

  12.  
  13. Remove the power window switch (A).

    Click image to see an enlarged view

    Fig. Remove the switch assembly (A)

  14.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  

Specific to:

Hyundai Accent 2006-2008

Hyundai Azera 2006-2008

Hyundai Elantra 2006-2008

Hyundai Sonata 2006-2008

Hyundai Tiburon 2006-2008

  1. Remove screws holding power window main switch to the door trim panel.
  2.  
  3. Remove the power window switch from the door trim panel.
  4.  
  5. Detach the connector from the switch to the window motor.
  6.  
  7. Installation is the reverse of the removal.
  8.  

 
label.common.footer.alt.autozoneLogo