Hyundai Santa Fe 2001-05

Trailing Arm

Print

Bushing Replacement



  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove the trailing arm.
  4.  
  5. Press the bushing from the trailing arm.
  6.  


NOTE
Position the groove in the arm bushing so that it is aligned as shown in the accompanying illustration, then press fit the bushing.

  1. Using tools 09216-21300 and 09552-38100, press fit the bushing.
  2.  


    Click image to see an enlarged view

    Fig. Using tools 09216-21300 and 09552-38100, press fit the trailing arm bushing



    Click image to see an enlarged view

    Fig. Position the groove in the arm bushing so that it is aligned as shown, before pressing the bushing into position


  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove the trailing arm.
  4.  
  5. Press the bushing from the trailing arm.
    NOTE
    Position the groove in the arm bushing so that it is aligned as shown in the accompanying illustration, then press fit the bushing.

  6.  
  7. Using tools 09216-21300 and 09552-38100, press fit the bushing.

    Click image to see an enlarged view

    Fig. Using tools 09216-21300 and 09552-38100, press fit the trailing arm bushing



    Click image to see an enlarged view

    Fig. Position the groove in the arm bushing so that it is aligned as shown, before pressing the bushing into position

  8.  

Removal & Installation



  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Support the vehicle under the lower control arm.
  4.  
  5. Remove or disconnect the following:

    Rear wheel
     
    Flange nut and brake caliper assembly
     
    Parking brake assembly
     
    Wheel Speed Sensor (WSS) and the parking brake cable
     
    Rear shock assembly
     
    Spring
     
    Rear driveshaft from the rear axle
     
    Upper and lower arm using tool 09517-43001.
     
    Trailing arm bolt and the arm
     

  6.  

To install:

  1. Install or connect the following:

    Trailing arm and tighten the trailing arm bolt to 118-133 (160-180 Nm)
     
    Upper and lower arm. Tighten the ball joint nut to 104-11 ft. lbs. (140-118 Nm).
     
    Spring and raise the jack into position
     
    Rear shock assembly
     
    Parking brake cable and WSS
     
    Parking brake assembly
     
    Flange nut and brake caliper assembly
     
    Rear wheel
     

  2.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Support the vehicle under the lower control arm.
  4.  
  5. Remove or disconnect the following:

    Rear wheel
     
    Flange nut and brake caliper assembly
     
    Parking brake assembly
     
    Wheel Speed Sensor (WSS) and the parking brake cable
     
    Rear shock assembly
     
    Spring
     
    Rear driveshaft from the rear axle
     
    Upper and lower arm using tool 09517-43001.
     
    Trailing arm bolt and the arm
     

  6.  

To install:

  1. Install or connect the following:

    Trailing arm and tighten the trailing arm bolt to 118-133 (160-180 Nm)
     
    Upper and lower arm. Tighten the ball joint nut to 104-11 ft. lbs. (140-118 Nm).
     
    Spring and raise the jack into position
     
    Rear shock assembly
     
    Parking brake cable and WSS
     
    Parking brake assembly
     
    Flange nut and brake caliper assembly
     
    Rear wheel
     

  2.  

 
label.common.footer.alt.autozoneLogo