Hyundai_Tucson_2005

Driven Disc & Pressure Plate

Print

Adjustments



The type of clutch system for this vehicle is hydraulic and as such does not have any adjustments.

These vehicles are equipped with a hydraulic self-adjusting clutch system. No adjustment is necessary.

Removal & Installation



  1. Remove the transaxle assembly.
  2.  
  3. Insert the special tool (09411-11000) in the clutch disc to prevent the disc from falling.

    Click image to see an enlarged view

    Fig. Diagram of inserted special tool 09411-11000

  4.  
  5. Loosen the bolts which attach the clutch cover to the flywheel in a star pattern. Loosen the bolts in succession, one or two turns at a time, to avoid bending the cover flange.
    NOTE
    Do not clean the clutch disc or the release bearing with cleaning solvent.



    Click image to see an enlarged view

    Fig. Diagram of bolt loosening pattern for clutch cover

  6.  
  7. Remove the release fork shaft and bushing.
  8.  
  9. Remove clutch cover assembly and then driven disc and pressure plate.
  10.  

To install:


CAUTION
When installing the clutch, apply grease to each part, but be careful not to apply excessive grease. It can cause clutch slippage and shudder.



Click image to see an enlarged view

Fig. Proper clutch greasing technique diagram

  1. Install the driven disc and pressure plate in to the clutch cover assembly.
  2.  
  3. Install the clutch disc assembly to the flywheel using the special tool (09411-11000).
  4.  
  5. Install the clutch cover assembly to the flywheel and temporarily tighten the bolts one or two steps at a time in a star pattern.
  6.  
  7. Tightening torque: Clutch cover bolt = 11-16 ft. lbs. (15-22 Nm).

    Click image to see an enlarged view

    Fig. Clutch cover installation placement diagram

  8.  
  9. Align the bearing (A) to the release fork (B) and then install it to the sleeve of the housing.
    CAUTION
    Apply multipurpose grease (CASMOLY L9508) to the bearing sleeve, contact point of the release fork (B) and the bushing inner surface (C).



    Click image to see an enlarged view

    Fig. Grease application diagram

  10.  
  11. Install the release lever to the release fork.

    Click image to see an enlarged view

    Fig. Release lever installation diagram

  12.  
  13. Install the transaxle assembly to the engine.
    CAUTION
    If the transaxle assembly is installed to the engine without performing this step, the release bearing can be separated, as the release fork rotates freely.

  14.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove the transaxle assembly.
  4.  
  5. Insert Special Tool 09411-11000 in the clutch disc to prevent the disc from falling.

    Click image to see an enlarged view

    Fig. Installing special tool 09411-11000

  6.  
  7. Remove or disconnect the following:

    Pressure plate bolts by loosening them evenly in a star pattern.
     
    Release fork shaft and bushing
     
    Pressure plate and clutch disc
     

  8.  

To install:

  1. Install or connect the following:

    Clutch disc on the flywheel
     
    Pressure plate and torque the bolts evenly in a crossing pattern to 11-16 ft. lbs. (15-22 Nm)

    Click image to see an enlarged view

    Fig. Pressure plate tightening sequence

     

  2.  
  3. Align the bearing to the release fork and then install it to the sleeve of the housing.
  4.  
  5. Install the release lever to the release fork.
  6.  
  7. Install the transaxle assembly.

    Click image to see an enlarged view

    Fig. Exploded view of the Clutch Disc and Pressure Plate components

  8.  

 
label.common.footer.alt.autozoneLogo