ION 2006-2007

Window Systems

Print

Door Glass & Regulator



Power Windows
Diagnosis & Testing
Driver's Window Switch
  1. Turn the ignition OFF, disconnect the harness connector at the driver window switch.
  2.  
  3. Test for infinite resistance between the signal terminals A and B and the B+ circuit terminal E with the passenger window switch in the INACTIVE position. If less than infinite resistance, replace the driver window switch.
  4.  
  5. Test for less than 2 ohms of resistance between the signal terminal A and the B+ circuit terminal E with the passenger window switch in the UP position. If greater than 2 ohms, replace the driver window switch.
  6.  
  7. Test for less than 2 ohms of resistance between the signal terminal B and the B+ circuit terminal E with the passenger window switch in the DOWN position. If greater than 2 ohms, replace the driver window switch.
  8.  
  9. Test for infinite resistance between the signal terminals F and H and the B+ circuit terminal E with the driver window switch in the INACTIVE position. If less than infinite resistance, replace the driver window switch.
  10.  
  11. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal E with the driver window switch in the UP position. If greater than 2 ohms, replace the driver window switch
  12.  
  13. Test for less than 2 ohms of resistance between the signal terminal H and the B+ circuit terminal E with the driver window switch in the DOWN position. If greater than 2 ohms, replace the driver window switch.
  14.  

Passenger's Window Switch
  1. Turn the ignition OFF, disconnect the harness connector at the passenger window switch. Test for infinite resistance between the signal terminals G and F and the B+ circuit terminal with the switch in the INACTIVE position. If less than infinite resistance, replace the switch.
  2.  
  3. Test for less than 2 ohms of resistance between the signal terminal G and the B+ circuit terminal with the switch in the UP position. If greater than 2 ohms, replace the switch.
  4.  
  5. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal with the switch in the DOWN position. If greater than 2 ohms, replace the switch.
  6.  

Window Motor
  1. Install a 30-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The motor should perform the UP or DOWN function.
  2.  
  3. If the function does not perform as specified, replace the motor.
  4.  
  5. Reverse the jumper wires; the motor should perform the DOWN or UP function.
  6.  
  7. If the function does not perform as specified, replace the motor.
  8.  

Removal & Installation
Window Motor & Regulator
  1. Raise the window to the full UP position.
  2.  
  3. Remove the upper trim panel.
  4.  
  5. Remove the manual window regulator handle, if equipped.
  6.  
  7. Remove the power door lock switch, if equipped.
  8.  
  9. Remove the pull cup assembly.
  10.  
  11. Remove the door trim push-in retainers.
  12.  
  13. Remove the screw from the trim panel.
  14.  
  15. Pull the bottom of the door trim out to disengage the clips.
  16.  
  17. Lift up on the door trim panel to disengage the inner belt molding from the door flange.
  18.  
  19. Remove the door trim panel.
  20.  
  21. Remove the radio speaker.
  22.  
  23. Remove the front door water deflector.
  24.  
  25. Disengage the door glass to the regulator sash channel clips. Separate the door glass from the sash channel.
  26.  
  27. Push the window to the up position and tape in place.
  28.  
  29. Loosen the power window regulator bolts.
  30.  
  31. Remove the rear regulator bolt.
  32.  
  33. Lift the window regulator, disengaging the loosened bolts from the door.
  34.  
  35. Disconnect the regulator electrical connector.
  36.  
  37. Remove the power window regulator from the door.
  38.  

To install:

  1. Installation is the reverse of removal.
  2.  

Window Switch
  1. Using a flat-bladed tool, pry the switch from the door trim panel enough to expose the locking tabs.
  2.  
  3. Press the locking tab to remove the switch from the door trim panel.
  4.  
  5. Disconnect the electrical connector.
  6.  
  7. Remove the switch.
  8.  

To install:

  1. Installation is the reverse of removal.
  2.  

 
label.common.footer.alt.autozoneLogo