ISUZU Amigo/Pick-ups/Rodeo/Trooper 1981-1996

Seat Belt System

Print

REMOVAL & INSTALLATION



See Figures 1, 2, 3, 4 and 5



Click image to see an enlarged view

Fig. Fig. 1: Front seat belt assembly-1981-84 Pick-up



Click image to see an enlarged view

Fig. Fig. 2: From and Rear seat belt assembly-Amigo



Click image to see an enlarged view

Fig. Fig. 3: Rear seat belt assembly-Trooper and Rodeo



Click image to see an enlarged view

Fig. Fig. 4: Front seat belt assembly-Hombre



Click image to see an enlarged view

Fig. Fig. 5: Seat belt buckle assembly-Hombre

  1. Disconnect the negative battery cable.
  2.  
  3. If removing a front seat belt assembly:
    1. Remove the cover from the door pillar anchor bolt, and remove the bolt.
    2.  
    3. Remove the door pillar trim panel to access the seat belt retract mechanism. If a wire harness is attach to the mechanism, unfasten it.
    4.  
    5. Remove the seat belt retract mechanism.
    6.  
    7. To remove the lock mechanism between the front seats, remove the retainer bolt securing the assembly to the floor. If a door buzzer harness is attached, unfasten it before removing the assembly from the vehicle.
    8.  

  4.  
  5. If removing a rear seat belt assembly, proceed with the following steps:
    1. Remove the trim cover over the anchor bolt, and remove the bolt.
    2.  
    3. Remove the rear interior panel to access the seat belt retract mechanism. If a wire harness is attach to the mechanism, unfasten it.
    4.  
    5. Remove the seat belt retract mechanism.
    6.  
    7. Remove the floor seat cushion, or move it forward to access the lock mechanism. Remove the lock assembly retainer bolt, and lift the assembly out.
    8.  

  6.  

To install:
  1. If installing a rear seat belt assembly, proceed with the following steps:
    1. Position the lock assembly to the floor, and secure with the retainer bolt, tighten to 22-36 ft. lbs. (29-47 Nm). Install the floor seat cushion.
    2.  
    3. Install the seat belt retract mechanism to the bracket, and tighten the retainer bolt to 22-36 ft. lbs. (29-47 Nm).
    4.  
    5. If a wire harness is attach to the seat belt mechanism, attach it, then install the rear interior panel over the seat belt retract mechanism.
    6.  
    7. Install the seat belt anchor bolts to the vehicle. Tighten the bolt to 22-36 ft. lbs. (29-47 Nm), then install the trim cover over the anchor bolt.
    8.  

  2.  
  3. If installing a front seat belt assembly:
    1. Install the lock mechanism to the floor in between the front seats. Secure the assembly with a retainer bolt, and tighten to 22-36 ft. lbs. (29-47 Nm). Connect the buzzer harness if equipped.
    2.  
    3. Install the seat belt retract mechanism. Attach the retainer bolt and tighten to 22-36 ft. lbs. (29-47 Nm).
    4.  
    5. If a wire harness is attach to the seat belt mechanism, attach it, then install the door pillar trim panel over the seat belt retract mechanism.
    6.  
    7. Install the seat belt anchor bolt, and tighten to 22-36 ft. lbs. (29-47 Nm). Install the cover over the door pillar anchor bolt.
    8.  

  4.  
  5. Connect the negative battery cable.
  6.  
  7. Test the seat belt to make sure it locks into place, and disengages easily.
  8.  

 
label.common.footer.alt.autozoneLogo