Infiniti Car 1998-05

Halfshafts

Print

CV-Joints Overhaul



Final Drive Side

NOTE
Procedures apply to front and rear halfshafts.

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Plug seal from the slide joint by gently tapping around the joint with a hammer
     
    Boot bands
     

  4.  
  5. Put matchmarks on the slide joint housing and halfshaft prior to separating the joint assembly.
  6.  
  7. Matchmark the spider assembly and driveshaft.
    NOTE
    Do not disassemble the spider assembly.


    NOTE
    Cover the halfshaft serrations with tape, so as not to damage the boot.



    Snapring and the spider assembly
     



    Slide joint housing and the boot
     



    Click image to see an enlarged view

    Fig. Exploded view of front halfshaft-G35 and M35 AWD

  8.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
    1. Install the boot and new boot band on the halfshaft.
    2.  
    3. Install the spider assembly making sure the matchmarks made during removal are properly aligned.
      NOTE
      The spider is press fit with the serration chamfer facing the shaft.

    4.  
    5. Install a new snapring.
    6.  

  2.  
  3. Pack the joint with 4.37-4.73 ounces (124-134g) of grease.
    1. Install the slide joint housing and the snapring.
    2.  
    3. Ensure that the boot is properly installed on the halfshaft groove
    4.  

  4.  
  5. Set the boot so that it does not swell or deform when its length is 3.70 in. (94mm).
  6.  
  7. Lock the new boot bands securely.
  8.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Plug seal from the slide joint by gently tapping around the joint with a hammer
     
    Boot bands
     

  4.  
  5. Put matchmarks on the slide joint housing and halfshaft prior to separating the joint assembly
  6.  
  7. Matchmark the spider assembly and driveshaft
    NOTE
    Do not disassemble the spider assembly.


    NOTE
    Cover the halfshaft serration-s with tape, so as not to damage the boot.



    Snapring and the spider assembly
     



    Slide joint housing and the boot
     

  8.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary
  2.  
  3. Install or connect the following:
    NOTE
    The spider is a press fit with the serration chamfer facing the shaft.


    NOTE
    Hold the plug seal horizontally when pressing it into place. This will prevent the spring inside from falling down or tilting.



    Boot and small boot band on the halfshaft
     
    Joint housing onto halfshaft
     
    Spider assembly, making sure the matchmarks are properly aligned
     



    Snapring
     
    Coil spring, spring cap and new plug seal to the slide joint housing. Apply a suitable sealant to the plug seal prior to installation
     

  4.  
  5. Move the shaft in an axial direction to make sure that the spring is installed properly. If there is a drag or the spring is installed improperly, replace the plug seal with a new one.
  6.  
  7. Pack the halfshaft with 5.82-6.17 ounces (165-175g) of grease.
  8.  
  9. Ensure that the boot is properly installed on the halfshaft groove
  10.  
  11. Set the boot so that it does not swell or deform when its length is 3.66-3.74 in. (93-95mm).
  12.  
  13. Lock the new boot bands securely.
  14.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Plug seal from the slide joint by gently tapping around the joint with a hammer
     
    Boot bands
     

  4.  
  5. Put matchmarks on the slide joint housing and halfshaft prior to separating the joint assembly.
  6.  
  7. Matchmark the spider assembly and driveshaft.
    NOTE
    Do not disassemble the spider assembly.


    NOTE
    Cover the halfshaft serration-s with tape, so as not to damage the boot.



    Snapring and the spider assembly
     



    Slide joint housing and the boot
     

  8.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
    1. Install the boot and new boot band on the halfshaft.
    2.  
    3. Install the spider assembly making sure the matchmarks made during removal are properly aligned.
      NOTE
      The spider is press fit with the serration chamfer facing the shaft.

    4.  
    5. Install a new snapring.
    6.  

  2.  
  3. Pack the joint with 4.37-4.73 ounces (124-134g) of grease.
    1. Install the slide joint housing and the snapring.
    2.  
    3. Ensure that the boot is properly installed on the halfshaft groove
    4.  

  4.  
  5. Set the boot so that it does not swell or deform when its length is 3.70 in. (94mm).
  6.  
  7. Lock the new boot bands securely.
  8.  

Transaxle Side
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Disassemble the joint as follows:
    1. Remove the boot bands.
    2.  
    3. Matchmark the slide joint housing and inner race before separating the assembly.
    4.  
    5. Using a suitable prytool, remove the stopper ring and pull out the slide joint
    6.  
    7. Matchmark the inner race and driveshaft.
    8.  
    9. Remove the snap-ring.
    10.  
    11. Remove the ball cage, inner race and balls as a unit.
    12.  
    13. Remove the boot.
      NOTE
      Cover the halfshaft serration-s with tape, so as not to damage the boot.

    14.  

  4.  

To install:

  1. Assemble the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  

  2.  
  3. Install a new inner snapring.
  4.  
  5. Install the ball cage, inner race and balls as a unit. Confirm that the matchmarks are aligned.
  6.  
  7. Install a new outer snapring.
  8.  
  9. Pack the CV joint with 5.8-6.17 ounces of grease.
  10.  
  11. Ensure that the boot is properly installed on the halfshaft groove.
  12.  
  13. Set the boot so that it does not swell or deform when its length is 3.82-3.90 in. (97-99mm).
  14.  
  15. Lock the new boot bands securely.
  16.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Disassemble the joint as follows:
    1. Remove the boot bands.
    2.  
    3. Matchmark the slide joint housing and inner race before separating the assembly
    4.  
    5. Using a suitable prytool, remove the stopper ring and pull out the slide joint
    6.  
    7. Matchmark the inner race and halfshaft
    8.  
    9. Remove the snapring.
    10.  
    11. Remove the ball cage, inner race and balls as a unit.
    12.  
    13. Remove the boot.
      NOTE
      Cover the halfshaft serration-s with tape, so as not to damage the boot.



      Click image to see an enlarged view

      Fig. Exploded view of the halfshaft-I35

    14.  

  4.  

To install:

  1. Assemble the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  

  2.  
  3. Install a new inner snapring.
  4.  
  5. Install the ball cage, inner race and balls as a unit. Confirm that the matchmarks are aligned.
  6.  
  7. Install a new outer snapring.
  8.  
  9. Pack the CV joint with 5.8-6.17 ounces of grease.
  10.  
  11. Ensure that the boot is properly installed on the halfshaft groove.
  12.  
  13. Set the boot so that it does not swell or deform when its length is 3.82-3.90 in. (97-99mm).
  14.  
  15. Lock the new boot bands securely.
  16.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:

    Plug seal from the slide joint by gently tapping around the joint with a hammer
     
    Boot bands
     

  4.  
  5. Put matchmarks on the slide joint housing and halfshaft prior to separating the joint assembly.
  6.  
  7. Matchmark the spider assembly and driveshaft.
    NOTE
    Do not disassemble the spider assembly.


    NOTE
    Cover the halfshaft serration-s with tape, so as not to damage the boot.



    Snap-ring and the spider assembly
     



    Slide joint housing and the boot
     

  8.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
  2.  
  3. Install or connect the following:
    NOTE
    The spider is press fit with the serration chamfer facing the shaft.


    NOTE
    Hold the plug seal horizontally when pressing it into place. This will prevent the spring inside from falling down or tilting.



    Boot and small boot band on the halfshaft
     
    Joint housing onto halfshaft
     
    Spider assembly making sure the matchmarks are properly aligned
     



    Snap-ring
     
    Coil spring, spring cap and new plug seal to the slide joint housing. Apply a suitable sealant to the plug seal prior to installation
     

  4.  
  5. Move the shaft in an axial direction to make sure that the spring is installed properly. If there is a drag or the spring is installed improperly, replace the plug seal with a new one.
  6.  
  7. Pack the halfshaft with 5.82-6.17 ounces (165-175g) of grease.
  8.  
  9. Ensure that the boot is properly installed on the halfshaft groove.
  10.  
  11. Set the boot so that it does not swell or deform when its length is 3.66-3.74 in. (93-95mm).
  12.  
  13. Lock the new boot bands securely.
  14.  

Transaxle Side-Ds83 Type
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Disassemble the joint as follows:
    1. Remove the boot bands.
    2.  
    3. Matchmark the slide joint housing and inner race before separating the assembly.
    4.  
    5. Using a suitable prytool, remove the stopper ring and pull out the slide joint
    6.  
    7. Matchmark the inner race and driveshaft.
    8.  
    9. Remove the snap-ring.
    10.  
    11. Remove the ball cage, inner race and balls as a unit.
    12.  
    13. Remove the boot.
      NOTE
      Cover the halfshaft serration-s with tape, so as not to damage the boot.



      Click image to see an enlarged view

      Fig. The inner CV joint uses a large C-clip to retain the ball and cage assembly in the outer housing-1998-2001 G20



      Click image to see an enlarged view

      Fig. After the outer housing is removed, the ball and cage assembly can slide from the shaft by removing the C-clip-1998-2001 G20

    14.  

  4.  

To install:

  1. Assemble the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.

      Click image to see an enlarged view

      Fig. Make sure to properly position the boot before tightening the boot clamps-1998-2001 G20

    4.  
    5. Install a new inner snapring.
    6.  
    7. Install the ball cage, inner race and balls as a unit. Confirm that the matchmarks are aligned.
    8.  
    9. Install a new outer snapring.
    10.  
    11. Pack the CV joint with 5.0-6.0 ounces of grease.
    12.  
    13. Ensure that the boot is properly installed on the halfshaft groove.
    14.  
    15. Set the boot so that it does not swell or deform when its length is 3.82-3.90 in. (97-99mm).
    16.  
    17. Lock the new boot bands securely.
    18.  

  2.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Disassemble the joint as follows:
    1. Remove the boot bands.
    2.  
    3. Matchmark the slide joint housing and inner race before separating the assembly
    4.  
    5. Using a suitable prytool, remove the stopper ring and pull out the slide joint
    6.  
    7. Matchmark the inner race and halfshaft
    8.  

  4.  
  5. Remove or disconnect the following:
    NOTE
    Cover the halfshaft serrations with tape, so as not to damage the boot.



    Snapring
     
    Ball cage, inner race and balls as a unit
     
    Boot

    Click image to see an enlarged view

    Fig. The inner CV joint uses a large C-clip to retain the ball and cage assembly in the outer housing-2002 G20



    Click image to see an enlarged view

    Fig. After the outer housing is removed, the ball and cage assembly can slide from the shaft by removing the C-clip-2002 G20

     

  6.  

To install:

  1. Assemble the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  
    5. Install a new inner snapring.
    6.  
    7. Install the ball cage, inner race and balls as a unit. Confirm that the matchmarks are aligned.
    8.  
    9. Install a new outer snapring.
    10.  
    11. Pack the CV joint with 5.0-6.0 ounces of grease.
    12.  
    13. Ensure that the boot is properly installed on the halfshaft groove.
    14.  
    15. Set the boot so that it does not swell or deform when its length is 3.82-3.90 in. (97-99mm).
    16.  
    17. Lock the new boot bands securely.
    18.  

  2.  

Transaxle Side-Ts83 Type
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Disassemble the joint as follows:
    1. Remove the boot bands.
    2.  
    3. Matchmark the slide joint housing and inner race before separating the assembly.
    4.  
    5. Matchmark the spider assembly and driveshaft
    6.  
    7. Remove the snap-ring and the spider assembly.
      NOTE
      Do not disassemble the spider assembly.

    8.  
    9. Remove the boot.
      NOTE
      Cover the halfshaft serration-s with tape, so as not to damage the boot.

    10.  

  4.  

To install:

  1. Assemble the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  
    5. Install the spider assembly making sure the matchmarks made during removal are properly aligned.
    6.  
    7. Install a new snapring.
    8.  
    9. Pack the joint with 4.5-5.11 ounces (124-145g) of grease.
    10.  
    11. Install the slide joint housing.
    12.  
    13. Ensure that the boot is properly installed on the halfshaft groove.
    14.  
    15. Set the boot so that it does not swell or deform when its length is 3.90 in. (99mm).
    16.  

  2.  
  3. Lock the new boot bands securely.
  4.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Disassemble the joint as follows:
    1. Remove the boot bands.
    2.  
    3. Matchmark the slide joint housing and inner race before separating the assembly.
    4.  
    5. Matchmark the spider assembly and driveshaft.
    6.  
    7. Remove the snapring and the spider assembly.
      NOTE
      Do not disassemble the spider assembly.

    8.  
    9. Remove the boot.
      NOTE
      Cover the halfshaft serrations with tape, so as not to damage the boot.

    10.  

  4.  

To install:

  1. Assemble the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  
    5. Install the spider assembly making sure the matchmarks made during removal are properly aligned.
    6.  
    7. Install a new snapring.
    8.  
    9. Pack the joint with 4.5-5.11 ounces (124-145g) of grease.
    10.  
    11. Install the slide joint housing.
    12.  
    13. Ensure that the boot is properly installed on the halfshaft groove.
    14.  
    15. Set the boot so that it does not swell or deform when its length is 3.90 in. (99mm).
    16.  

  2.  
  3. Lock the new boot bands securely.
  4.  

Wheel Side
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  

The joint on the wheel side cannot be disassembled.

  1. Prior to separating the joint assembly, matchmark the halfshaft and joint assembly.
  2.  
  3. Separate the joint using a slide hammer.
  4.  
  5. Remove the boot bands.
  6.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
    NOTE
    Cover the halfshaft serration-s with tape, so as not to damage the boot.



    Click image to see an enlarged view

    Fig. Use vinyl tape and wrap the end of the shaft to protect the boot during installation-1998-2001 G20

  2.  
  3. Install the boot and small boot band on the halfshaft.
  4.  
  5. Set the joint assembly onto the halfshaft and align the matchmarks.
  6.  
  7. Attach the joint assembly to the halfshaft by lightly tapping the serrated end with a plastic hammer.
    NOTE
    Using a metal hammer may damage the threads on the end of the joint.



    Click image to see an enlarged view

    Fig. Use an old nut to protect the threads when tapping the outer CV joint onto the shaft-1998-2001 G20

  8.  
  9. Pack the CV joint with 3.5-4.0 ounces of grease.
  10.  
  11. Ensure that the boot is properly installed on the halfshaft groove.
  12.  
  13. Set the boot so that it does not swell or deform when its length is 3.327-3.406 in. (84.5-86.5mm).
  14.  
  15. Lock the new boot bands securely.
  16.  


NOTE
The joint on the wheel side cannot be disassembled.

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Prior to separating the joint assembly, matchmark the halfshaft and joint assembly.
  4.  
  5. Separate the joint using a slide hammer.
  6.  
  7. Remove the boot bands.
  8.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
    NOTE
    Cover the halfshaft serrations with tape, so as not to damage the boot.



    Click image to see an enlarged view

    Fig. Use vinyl tape and wrap the end of the shaft to protect the boot during installation-2002 G20

  2.  
  3. Install the boot and small boot band on the halfshaft.
  4.  
  5. Set the joint assembly onto the halfshaft and align the matchmarks.
  6.  
  7. Attach the joint assembly to the halfshaft by lightly tapping the serrated end with a plastic hammer.
    NOTE
    Using a metal hammer may damage the threads on the end of the joint.



    Click image to see an enlarged view

    Fig. Use an old nut or wooden hammer to protect the threads when tapping the outer CV joint onto the shaft-2002 G20

  8.  
  9. Pack the CV joint with 3.5-4.0 ounces of grease.
  10.  
  11. Ensure that the boot is properly installed on the halfshaft groove.
  12.  
  13. Set the boot so that it does not swell or deform when its length is 3.327-3.406 in. (84.5-86.5mm).
  14.  
  15. Lock the new boot bands securely.
  16.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:


    1. Remove the boot bands.
    2.  
    3. Thread a slide hammer into the joint sub-assembly and pull the joint out of the shaft.
      NOTE
      Do not disassemble the spider assembly.

    4.  
    5. Remove the boot.
    6.  

  4.  

To install:

  1. Install the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Pack the joint with 3.03-3.39 ounces (86-96g) of grease.
    4.  
    5. Install the boot and new boot band on the halfshaft.
    6.  
    7. Install a new snapring.
    8.  
    9. Ensure that the boot is properly installed on the halfshaft groove.
    10.  

  2.  
  3. Set the boot so that it does not swell or deform when its length is 3.82 in. (97mm).
  4.  
  5. Lock the new boot bands securely.
  6.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  

The joint on the wheel side cannot be disassembled.

  1. Prior to separating the joint assembly, matchmark the halfshaft and joint assembly.
  2.  
  3. Separate the joint using a slide hammer.
  4.  
  5. Remove the boot bands.
  6.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
    NOTE
    Cover the halfshaft serration-s with tape, so as not to damage the boot.

  2.  
  3. Install the boot and small boot band on the halfshaft.
  4.  
  5. Set the joint assembly onto the halfshaft and align the matchmarks.
  6.  
  7. Attach the joint assembly to the halfshaft by lightly tapping the serrated end with a plastic hammer.
    NOTE
    Using a metal hammer may damage the threads on the end of the joint.

  8.  
  9. Pack the CV joint with 4.7-5.11 ounces of grease.
  10.  
  11. Ensure that the boot is properly installed on the halfshaft groove.
  12.  
  13. Set the boot so that it does not swell or deform when its length is 3.78-3.86 in. (96-98mm).
  14.  
  15. Lock the new boot bands securely.
  16.  


NOTE
The joint on the wheel side cannot be disassembled.

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Prior to separating the joint assembly, matchmark the halfshaft and joint assembly.
  4.  
  5. Separate the joint using a slide hammer.
  6.  
  7. Remove the boot bands.
  8.  

To assemble:

  1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage and replace as necessary.
    NOTE
    Cover the halfshaft serration-s with tape, so as not to damage the boot.

  2.  
  3. Install the boot and small boot band on the halfshaft.
  4.  
  5. Set the joint assembly onto the halfshaft and align the matchmarks.
  6.  
  7. Attach the joint assembly to the halfshaft by lightly tapping the serrated end with a plastic hammer.
    NOTE
    Using a metal hammer may damage the threads on the end of the joint.

  8.  
  9. Pack the CV joint with 4.7-5.11 ounces of grease.
  10.  
  11. Ensure that the boot is properly installed on the halfshaft groove.
  12.  
  13. Set the boot so that it does not swell or deform when its length is 3.78-3.86 in. (96-98mm)
  14.  
  15. Lock the new boot bands securely
  16.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:


    1. Remove the boot bands.
    2.  
    3. Matchmark the housing with the shaft and halfshaft before separating the assembly.
    4.  
    5. Matchmark the spider assembly and halfshaft.
    6.  
    7. Remove the snap-ring and the spider assembly.
      NOTE
      Do not disassemble the spider assembly.

    8.  
    9. Remove the boot.
      NOTE
      Cover the halfshaft serration-s with tape, so as not to damage the boot.

    10.  

  4.  

To install:

  1. Install the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  
    5. Install the spider assembly making sure the matchmarks made during removal are properly aligned.
      NOTE
      The spider is press fit with the serration chamfer facing the shaft.

    6.  
    7. Install a new snapring.
    8.  

  2.  
  3. Pack the joint with 4-4.34 ounces (113-123g) of grease.
    1. Install the slide joint housing and the snap-ring.
    2.  
    3. Ensure that the boot is properly installed on the halfshaft groove.
    4.  

  4.  
  5. Set the boot so that it does not swell or deform when its length is 3.78-3.86 in. (96-98mm).
  6.  
  7. Lock the new boot bands securely.
  8.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:


    1. Remove the boot bands.
    2.  
    3. Matchmark the housing with the shaft and halfshaft before separating the assembly
    4.  
    5. Matchmark the spider assembly and halfshaft
    6.  
    7. Remove the snapring and the spider assembly.
      NOTE
      Do not disassemble the spider assembly.

    8.  
    9. Remove the boot.
      NOTE
      Cover the halfshaft serration-s with tape, so as not to damage the boot.

    10.  

  4.  

To install:

  1. Install the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Install the boot and new boot band on the halfshaft.
    4.  
    5. Install the spider assembly making sure the matchmarks made during removal are properly aligned.
      NOTE
      The spider is press fit with the serration chamfer facing the shaft.

    6.  
    7. Install a new snapring.
    8.  

  2.  
  3. Pack the joint with 4-4.34 ounces (113-123g) of grease.
    1. Install the slide joint housing and the snapring.
    2.  
    3. Ensure that the boot is properly installed on the halfshaft groove.
    4.  

  4.  
  5. Set the boot so that it does not swell or deform when its length is 3.78-3.86 in. (96-98mm).
  6.  
  7. Lock the new boot bands securely.
  8.  

  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Remove or disconnect the following:


    1. Remove the boot bands.
    2.  
    3. Thread a slide hammer into the joint sub-assembly and pull the joint out of the shaft.
      NOTE
      Do not disassemble the spider assembly.

    4.  
    5. Remove the boot.
    6.  

  4.  

To install:

  1. Install the joint as follows:
    1. Thoroughly clean all parts in solvent and dry with compressed air. Check parts for evidence of damage, and replace as necessary.
    2.  
    3. Pack the joint with 3.03-3.39 ounces (86-96g) of grease.
    4.  
    5. Install the boot and new boot band on the halfshaft.
    6.  
    7. Install a new snapring.
    8.  
    9. Ensure that the boot is properly installed on the halfshaft groove.
    10.  

  2.  
  3. Set the boot so that it does not swell or deform when its length is 3.82 in. (97mm).
  4.  
  5. Lock the new boot bands securely.
  6.  

 
label.common.footer.alt.autozoneLogo