Isuzu_Amigo_1998-2000

Power Door Locks

Print

Door Lock Motor



Removal & Installation
Front Doors

This procedure covers removal of the door lock assembly.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove power window switch/regulator handle as follows:
    1. Power windows: Pry out the power window switch and remove the connectors.
    2.  
    3. Manual windows: To remove the regulator handle (1), remove the clip (2), at the root of the handle by using wire with hook.

      Click image to see an enlarged view

      Fig. To remove the regulator handle (1), remove the clip (2), at the root of the handle by using wire with hook

    4.  

  4.  
  5. Remove the screw while pulling the inside lever toward you and then remove the inside handle
  6.  
  7. Remove speaker grille, as follows:
    1. Pull out the front side of the grille.
    2.  

  8.  
  9. Remove 4 screws and disconnect the speaker harness connector, then remove the speaker.
  10.  
  11. Remove courtesy light lens.
  12.  
  13. Remove 5 screws (1), (3) and pull out the door trim panel at the 6 clip (2) positions.

    Click image to see an enlarged view

    Fig. Remove 5 screws (1), (3) and pull out the door trim panel at the 6 clip (2) positions.

  14.  
  15. Note the location of the door harness, peel the waterproof sheet off the door panel carefully.
  16.  
  17. Raise the glass up to the uppermost position, and then remove the rear guide rail.
  18.  
  19. Disconnect the locking links then remove the door lock assembly fixing screws and door lock assembly.

    Click image to see an enlarged view

    Fig. 1. Outside handle 2. Door locking link 3. Door lock assembly 4. Waterproof sheet 5. Door trim panel 6. Courtesy light lens 7. Speaker grille 8. Grip cover 9. Inside handle 10. Power window switch/regulator handle 11. Speaker

  20.  

To install:

  1. To install, follow the removal steps in the reverse order, noting the following points:
    1. Apply chassis grease to the lock assembly and striker moving surface.
    2.  
    3. Install the regulator handle as shown in the illustration, if equipped without power windows.

      Click image to see an enlarged view

      Fig. If equipped with manual windows, install the regulator handle as shown

    4.  
    5. Tighten the door lock assembly mounting screws to 61 inch lbs. (7 Nm).
    6.  
    7. Check that the door lock operates smoothly.
    8.  

  2.  

Rear Doors

This procedure covers removal of the door lock assembly.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove rear corner garnish.
  4.  
  5. Remove courtesy light lens.
  6.  
  7. Remove window regulator handle, by removing the clip on the rear side of the regulator handle using a wire.
  8.  
  9. Remove the screw while pulling the inside lever toward you and then remove the inside handle.
  10.  
  11. Remove the 2 screws at the pull case and courtesy light.
  12.  
  13. Pull out the trim panel at the 8 clip positions. Disconnect the power window switch connector and courtesy light connector.

    Click image to see an enlarged view

    Fig. Pull out the trim panel at the 8 clip positions. Disconnect the power window switch connector and courtesy light connector

  14.  
  15. Remove power window switch, if equipped.
  16.  
  17. Remove bracket.
  18.  
  19. Note the location of the door harness, peel the waterproof sheet off the door panel carefully.
  20.  
  21. Disconnect the locking links and remove the door lock assembly fixing screws to remove the door lock assembly.

    Click image to see an enlarged view

    Fig. 1. Outside handle 2. Door locking link 3. Bracket 4. Rear corner garnish 5. Door trim panel 6. Courtesy light lens 7. Power window switch/regulator handle 8. Inside handle 9. Waterproof sheet

  22.  

To install:

  1. To install, follow the removal steps in the reverse order, noting the following points:
    1. Apply chassis grease to the lock assembly and striker moving surface.
    2.  
    3. Install the regulator handle as shown in the illustration, if equipped without power windows.

      Click image to see an enlarged view

      Fig. If equipped with manual windows, install the regulator handle as shown

    4.  
    5. Tighten the door lock assembly mounting screws to 61 inch lbs. (7 Nm).
    6.  
    7. Check that the door lock operates smoothly.
    8.  

  2.  

 
label.common.footer.alt.autozoneLogo