Isuzu Axiom 2002-05

Transmission Removal & Installation

Print

A340e



2-Wheel Drive
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Driveshaft
     
    Fuel line bracket from the transmission
     
    Wiring harness heat shield
     
    Transmission harness connectors
     

  4.  
  5. Support the transmission with a jack.
  6.  
  7. Remove or disconnect the following:

    Transmission mount and crossmember
     
    Transmission oil cooler lines
     
    Selector cable
     
    Starter motor
     
    Undercovers
     
    Torque converter bolts
     
    Transmission flange bolts
     
    Transmission
     

  8.  

To install:


NOTE
Use new torque converter bolts.

  1. Install or connect the following:

    Transmission. Tighten the large bolts to 56 ft. lbs. (76 Nm) and the small bolts to 69 inch lbs. (8 Nm).
     
    Torque converter. Tighten the bolts to 40 ft. lbs. (54 Nm).
     
    Under covers
     
    Starter motor. Tighten the bolts to 30 ft. lbs. (40 Nm).
     
    Selector cable
     
    Transmission oil cooler lines
     
    Crossmember. Tighten the bolts to 85 ft. lbs. (116 Nm).
     
    Transmission mount. Tighten the bolts to 37 ft. lbs. (50 Nm).
     
    Transmission harness connectors
     
    Wiring harness heat shield
     
    Fuel line bracket
     
    Driveshaft. Tighten the flange bolts to 46 ft. lbs. (63 Nm).
     
    Negative battery cable
     

  2.  

A340f



4-Wheel Drive
  1. Before servicing the vehicle, refer to the precautions section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Skid plate
     
    Driveshafts
     
    Center exhaust pipe
     
    Fuel line bracket from the transmission
     
    Wiring harness heat shield
     
    Transmission harness connectors
     

  4.  
  5. Support the transmission with a jack.
  6.  
  7. Remove or disconnect the following:

    Transmission mount and crossmember
     
    Transmission oil cooler lines
     
    Selector cable
     
    Starter motor
     
    Undercovers
     
    Torque converter bolts
     
    Transmission flange bolts
     
    Transmission
     

  8.  

To install:


NOTE
Use new torque converter bolts.

  1. Install or connect the following:

    Transmission. Tighten the large bolts to 56 ft. lbs. (76 Nm) and the small bolts to 69 inch lbs. (8 Nm).
     
    Torque converter. Tighten the bolts to 40 ft. lbs. (54 Nm).
     
    Under covers
     
    Starter motor. Tighten the bolts to 30 ft. lbs. (40 Nm).
     
    Selector cable
     
    Transmission oil cooler lines
     
    Crossmember. Tighten the bolts to 85 ft. lbs. (116 Nm).
     
    Transmission mount. Tighten the bolts to 37 ft. lbs. (50 Nm).
     
    Transmission harness connectors
     
    Wiring harness heat shield
     
    Fuel line bracket
     
    Center exhaust pipe
     
    Driveshafts. Tighten the flange bolts to 46 ft. lbs. (63 Nm).
     
    Skid plate
     
    Negative battery cable
     

  2.  

 
label.common.footer.alt.autozoneLogo