Isuzu Axiom 2002-05

Door Glass & Regulator

Print

Power Windows



Removal & Installation
Motor & Regulator
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the mounting screw, then remove the pull box.

    Click image to see an enlarged view

    Fig. Remove the mounting screw, then remove the pull box

  4.  
  5. Remove the power window switch by prying the power window switch out and disconnect the switch connector.

    Click image to see an enlarged view

    Fig. Carefully pry the power window switch (1) out, then detach the electrical connector

  6.  
  7. Remove the inside handle by removing the screw cover and the screws, then disconnecting the cable.

    Click image to see an enlarged view

    Fig. Remove the inside handle by removing the screw cover and removing the screw, then disconnecting the cable

  8.  
  9. Remove the door mirror cover.
  10.  
  11. Remove the door trim panel with the eight clips (1) from the door panel.

    Click image to see an enlarged view

    Fig. The door trim panel has eight retaining clips (1)

  12.  
  13. Disconnect the tweeter and courtesy light connectors.
  14.  
  15. Remove the inner waist seal.
  16.  
  17. Remove the courtesy light.
  18.  
  19. Remove the tweeter.
  20.  
  21. Remove the pull box bracket.
  22.  
  23. Remove the inside lock bracket and disconnect the cable.
  24.  
  25. Remove the speaker, speaker spacer and detach the speaker connector.

    Click image to see an enlarged view

    Fig. 1. Glass 2. Glass Run 3. Door mirror 4. Door mirror cover 5. Tweeter 6. Speaker spacer 7. Speaker assembly 8. Inner waist seal 9. Door trim panel 10. Power window switch 11. Inside lock bracket 12. Inside handle 13. Pull box 14. Courtesy light 15. Pull box bracket 16. Waterproof sheet 17. Door panel 18. Door lock assembly 19. Door lock cylinder 20. Outside handle 21. Power window regulator 22. Outer waist seal

  26.  
  27. Carefully remove the waterproof sheet.
  28.  
  29. Remove the outer waist seal, by removing the rear side screw and pull the outer waist seal upward.
  30.  
  31. Remove the window glass, as follows:
    1. Temporarily connect the negative battery cable, then operate the regulator (power window switch) to adjust the glass height and expose the access hole.
    2.  
    3. Remove the 2 bolts fixing the bottom channel and the regulator. Remove the glass.

      Click image to see an enlarged view

      Fig. Remove the 2 bolts fixing the bottom channel and the regulator



      Click image to see an enlarged view

      Fig. Be very careful when removing the window glass

    4.  

  32.  
  33. Remove the window regulator mounting bolts and disconnect the window regulator motor harness connector.
  34.  
  35. Remove the glass run by carefully pulling it from the door frame.

    Click image to see an enlarged view

    Fig. Remove the glass run (6) by carefully pulling it from the door frame

  36.  
  37. Remove the power window motor screws, then remove the motor.

    Click image to see an enlarged view

    Fig. Window regulator (2) and power window motor assembly (1)

  38.  

To install:

  1. Installation is the reverse of the removal procedure, noting the following:
    1. Check to see that the window regulator operates smoothly and the glass opens and closes properly.
    2.  
    3. Install the waterproof sheet tightly against the door panel.
    4.  
    5. Tighten the window regulator assembly mounting bolts to 52 inch lbs. (6 Nm).
    6.  

  2.  

Switch
  1. Disconnect the negative battery cable.
  2.  
  3. Remove the power window switch by prying the power window switch out and disconnect the switch connector.
  4.  
  5. Installation is the reverse of the removal procedure.

    Click image to see an enlarged view

    Fig. Carefully pry the power window switch (1) out, then detach the electrical connector

  6.  

 
label.common.footer.alt.autozoneLogo