Isuzu I-280, I-350 2005-06

Arming The System

Imprimir

Zone 1



  1. Remove the key from the ignition.
  2.  
  3. Connect the sensor connectors to both (2) front end sensors.
  4.  
  5. Install the CPAs to both sensor connectors.
  6.  
  7. Remove the SIR fuse into the fuse block (1) located in the underhood fuse block.
  8.  
  9. Staying well away from all air bags, turn ON the ignition, with the engine OFF. The AIR BAG indicator will flash 7 times. The AIR BAG indicator will then turn OFF.
  10.  

Zone 2



  1. Remove the key from the ignition.
  2.  
  3. Connect the roof rail module connector (1) and install the garnish molding.
  4.  
  5. Connect the seat belt pretensioner, left, and install the CPA.
  6.  
  7. Install the trim panel. For extended cab install the rear access door wiring harness grommet.
  8.  
  9. Connect the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  10.  
  11. Install the CPA (3) to the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  12.  
  13. Install the left door trim panel.
  14.  
  15. Install the SIR fuse to the fuse block (1) located in the underhood fuse block.
  16.  
  17. Staying well away from all air bags, turn ON the ignition, with the engine OFF. The AIR BAG indicator will flash 7 times. The AIR BAG indicator will then turn OFF.
  18.  

Zone 3



  1. Remove the key from the ignition.
  2.  
  3. Connect the steering wheel module yellow 4-way connector (2) located left of the steering column above the left hinge pillar trim panel.
  4.  
  5. Install the CPA (1) to the steering wheel module yellow 4-way connector (2) located left of the steering column above the left hinge pillar trim panel.
  6.  
  7. Install the SIR fuse to the fuse block (1) located in the underhood fuse block.
  8.  
  9. Staying well away from all air bags, turn ON the ignition, with the engine OFF. The AIR BAG indicator will flash 7 times. The AIR BAG indicator will then turn OFF.
  10.  

Zone 5



  1. Remove the key from the ignition.
  2.  
  3. Connect the I/P module yellow 4-way inline connector C208 (2) located above the driver side kick panel.
  4.  
  5. Install the CPA to the I/P module yellow 4-way inline connector C208 (2) located above the driver side kick panel.
  6.  
  7. Install the SIR fuse to the fuse block (1) located in the underhood fuse block.
  8.  
  9. Staying well away from all air bags, turn ON the ignition, with the engine OFF. The AIR BAG indicator will flash 7 times. The AIR BAG indicator will then turn OFF.
  10.  

Zone 6



  1. Remove the key from the ignition.
  2.  
  3. Connect the roof rail module connector (1) and install the garnish molding.
  4.  
  5. Connect the seat belt pretensioner, right, and install the CPA.
  6.  
  7. Install the trim panel. For extended cab install the rear access door wiring harness grommet.
  8.  
  9. Connect the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  10.  
  11. Install the CPA (3) to the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  12.  
  13. Install the left door trim panel.
  14.  
  15. Install the SIR fuse to the fuse block (1) located in the underhood fuse block.
  16.  
  17. Staying well away from all air bags, turn ON the ignition, with the engine OFF. The AIR BAG indicator will flash 7 times. The AIR BAG indicator will then turn OFF.
  18.  

Zone 8



  1. Remove the key from the ignition.
  2.  
  3. Connect the steering wheel module yellow 4-way connector (1) located left of the steering column (2) above the left hinge pillar trim panel.
  4.  
  5. Install the CPA (1) to the steering wheel module yellow 4-way connector (1) located left of the steering column (2) above the left hinge pillar trim panel.
  6.  
  7. Connect the roof rail module connector (1) and install the garnish molding.
  8.  
  9. Connect the seat belt pretensioner, left, and install the CPA.
  10.  
  11. Install the trim panel. For extended cab install the rear access door wiring harness grommet.
  12.  
  13. Connect the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  14.  
  15. Install the CPA (3) to the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  16.  
  17. Install the left door trim panel.
  18.  
  19. Connect the I/P module yellow 4-way inline connector C208 (2) located above the driver door kick panel.
  20.  
  21. Install the CPA to the I/P module yellow 4-way inline connector C208 (2) located above the driver side kick panel.
  22.  
  23. Connect the roof rail module connector (1) and install the garnish molding.
  24.  
  25. Connect the seat belt pretensioner-right and install the CPA.
  26.  
  27. Install the trim panel. For extended cab install the rear access door wiring harness grommet.
  28.  
  29. Connect the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  30.  
  31. Install the CPA (3) to the side impact sensor yellow 2-way connector (5) located near the middle of the door.
  32.  
  33. Install the right door trim panel.
  34.  
  35. Install the SIR fuse to the fuse block (1) located in the underhood fuse block.
  36.  
  37. Staying well away from all air bags, turn ON the ignition, with the engine OFF. The AIR BAG indicator will flash 7 times. The AIR BAG indicator will then turn OFF.
  38.  

 
label.common.footer.alt.autozoneLogo