Isuzu I-280, I-350 2005-06

Door Glass & Regulator

Print

Power Windows



Removal & Installation
Motor
Front
  1. Remove the front door window regulator.
  2.  
  3. Drill a hole (1) through the window regulator bracket and lift arm.
  4.  
  5. Install a nut and bolt through the hole (1) to secure the lift arm while the motor is removed.

    Click image to see an enlarged view

    Fig. Securing lift arm with a nut and bolt

  6.  
  7. Remove the bolts retaining the front window regulator motor to the regulator bracket.
  8.  
  9. Remove the front window regulator motor from the regulator.

    Click image to see an enlarged view

    Fig. Removing front window regulator motor from the regulator

  10.  

To install:

  1. Install the front window regulator motor to the regulator.
  2.  
  3. Install the bolts retaining the front window regulator motor to the regulator bracket. Tighten the front window regulator motor bolts to 40 inch lbs. (4.5 Nm).
  4.  
  5. Remove the nut and bolt securing the lift arm to the regulator bracket.
  6.  
  7. Install the front window regulator to the front door.
  8.  

Rear
  1. Remove the rear door window regulator.
  2.  
  3. Remove the bolts retaining the rear window regulator motor to the regulator bracket.
  4.  
  5. Remove the rear window regulator motor from the regulator.

    Click image to see an enlarged view

    Fig. Removing rear window regulator from the regulator

  6.  

To install:

  1. Install the rear window regulator motor to the regulator.
  2.  
  3. Install the bolts retaining the rear window regulator motor to the regulator bracket. Tighten the rear window regulator motor bolts to 40 inch lbs. (4.5 Nm).
  4.  
  5. Install the rear door window regulator.
  6.  

Regulator
Front Door
  1. Remove the front door trim panel.
  2.  
  3. Remove the front door water deflector.
  4.  
  5. Remove the bolts retaining the front door window to the window regulator.
  6.  
  7. Remove the front door window by performing the following:
    1. Remove the front door outer belt sealing strip.
    2.  
    3. Remove the bolts retaining the front door window to the window regulator.

      Click image to see an enlarged view

      Fig. Removing front door window to regulator retaining bolts

    4.  
    5. Lift the window off of the window regulator.
    6.  
    7. Rotate the rear of the window upwards, disengaging the window from the window run channel.
    8.  
    9. Remove the window from between the inner and outer door panels.

      Click image to see an enlarged view

      Fig. Removing front window from between the inner and outer door panels

    10.  

  8.  
  9. Disconnect the electrical connector from the window regulator motor.
  10.  
  11. Loosen the bolts (1) retaining the window regulator to the inner panel at the keyhole slot locations.
  12.  
  13. Remove the remaining fasteners retaining the window regulator to the inner panel.
  14.  
  15. Remove the window regulator from the door by lifting the regulator up, and out of the keyhole slots, and removing the regulator out through the access hole.

    Click image to see an enlarged view

    Fig. Removing front door window regulator

  16.  

To install:

  1. Install the front door window regulator into the front door through the access hole.
  2.  
  3. Position the window regulator to the inner panel by sliding the regulator bolts (1) into the keyhole slots in the inner panel.
  4.  
  5. Install the fastener retaining the front door window regulator to the door. Tighten the front window regulator fasteners to 80 inch lbs. (9 Nm).
  6.  
  7. Connect the electrical connector to the window regulator motor.
  8.  
  9. Install the front door window by performing the following:
    1. Install the front door window into the front door between the inner and outer door panels.
    2.  
    3. Rotate the rear of the window down, positioning the window into the window run channels.
    4.  
    5. Lower the window down onto the window regulator.
    6.  
    7. Install the bolts retaining the front door window to the window regulator. Tighten the front window bolts to 80 inch lbs. (9 Nm).
    8.  
    9. Install the front door outer belt sealing strip.
    10.  

  10.  
  11. Install the front door water deflector.
  12.  
  13. Install the front door trim panel.
  14.  

Rear Door
  1. Remove the rear door trim panel.
  2.  
  3. Remove the rear inside door handle.
  4.  
  5. Remove the rear door speaker.
  6.  
  7. Remove the rear door water deflector.
  8.  
  9. Remove the bolts retaining the rear window to the window regulator.
  10.  
  11. Raise and support the rear door window.

    Click image to see an enlarged view

    Fig. Removing rear window-to-regulator retaining bolts

  12.  
  13. Disconnect the electrical connector from the window regulator motor.
  14.  
  15. Loosen the bolts retaining the window regulator (1) to the inner door at the keyhole slot (2) locations.
  16.  
  17. Remove the bolts retaining the window regulator to the inner panel.
  18.  
  19. Remove the window regulator (1) by lifting the regulator up, and out of the keyhole slots (2) in the inner panel, and removing the regulator out through the access hole.

    Click image to see an enlarged view

    Fig. Removing rear door window regulator

  20.  

To install:

  1. Install the rear door window regulator into the rear door through the access hole.
  2.  
  3. Position the rear door window regulator to the inner panel by inserting the regulator bolts to the keyhole slots on the inner panel.
  4.  
  5. Install the bolts retaining the rear door window regulator to the inner panel. Tighten the rear window regulator bolts to 80 inch lbs. (9 Nm).
  6.  
  7. Connect the electrical connector to the window regulator motor.
  8.  
  9. Remove the window support and lower the window onto the window regulator carrier plate.
  10.  
  11. Install the bolts retaining the window to the window regulator. Tighten the rear window bolts to 80 inch lbs. (9 Nm).
  12.  
  13. Install the rear door water deflector.
  14.  
  15. Install the rear door speaker.
  16.  
  17. Install the rear door inside handle.
  18.  
  19. Install the rear door trim panel.
  20.  

Switch
Front
  1. Remove the 2 screws securing the switch plate assembly to the door trim panel.
  2.  
  3. Lift the front of the switch plate up to disengage clip.
  4.  
  5. Remove the switch plate out of the door trim panel opening.

    Click image to see an enlarged view

    Fig. Removing switch plate out of the door trim panel opening-front

  6.  
  7. Disconnect the electrical connectors (3, 4) from the switches (2, 5).
  8.  
  9. Remove the switch plate assembly (1) from the vehicle.
  10.  
  11. If replacing only the switches, remove the switches from the plate.
  12.  
  13. If replacing only the switch plate, retain the switches for transfer.
  14.  

To install:

  1. Install the switches to the switch plate.
  2.  
  3. Connect the electrical connectors to the switches.
  4.  
  5. Install the switch plate assembly to the door trim panel with the 2 screws. Tighten the front door switch plate screws to 18 inch lbs. (2 Nm).
  6.  

Rear
  1. Remove the 2 screws securing the switch plate assembly to the door trim panel.
  2.  
  3. Lift the switch plate up and out of the door trim panel.

    Click image to see an enlarged view

    Fig. Removing the screws securing the switch plate assembly to the door trim panel

  4.  
  5. Disconnect the electrical connectors from the switch module.
  6.  
  7. Remove the switch plate assembly from the vehicle.
  8.  
  9. If replacing only the switch module, remove the module from the switch plate.
  10.  
  11. If replacing only the switch plate, retain the switch module for transfer.

    Click image to see an enlarged view

    Fig. Remove the switch plate assembly from the vehicle

  12.  

To install:

  1. Install the switch module to the switch plate.
  2.  
  3. Connect the electrical connector to the switch module.
  4.  
  5. Install the rear switch plate assembly to the door trim panel with the 2 screws. Tighten the rear door switch plate screws to 18 inch lbs. (2 Nm).
  6.  

 
label.common.footer.alt.autozoneLogo