Jaguar 2000-06

Instrument Panel & Pad

Print

Removal & Installation



  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Move the front seats to fully rearward position.
  4.  
  5. Place steering wheel in straight ahead position.
  6.  
  7. Remove or disconnect the following:

    Negative battery cable
     
    Selector lever finish panel
     
    Center console veneer panel
     
    Radio
     
    Center console
     
    Center console A/C duct
     
    Driver air bag
     
    Steering column covers
     
    Wiper switch
     
    Warning speaker
     
    Glove box
     
    A pillar trim pads
     
    Drive storage bin
     
    Center console and footwell electrical connectors
     
    Steering column electrical connectors
     
    Fascia mounting bracket
     
    Instrument panel end trim pads
     
    A/C unit fascia plate
     
    A/C unit to driveshaft tunnel bolts
     
    Electrical connectors underneath and behind instrument panel
     
    Instrument panel fascia panel retaining bolts
     
    Instrument panel fascia panel, with assistance
     
    Key transponder module
     
    Light switch module
     
    Control processor behind glove box opening
     
    Instrument panel veneer
     

  8.  

To install:

  1. To install, reverse the removal procedure.
  2.  
  3. Tighten steering column lower bolts to 15 ft. lbs. (20 Nm). Upper bolts to 18 ft. lbs. (25 Nm).
  4.  
  5. Tighten all instrument panel retaining bolts to 18 ft. lbs. (25 Nm).
  6.  
  7. Reconnect negative battery cable.
  8.  
  9. Refill the cooling system.
  10.  
  11. Recharge the air conditioning system.
  12.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Cowl vent screen
     
    Engine compartment brace
     
    Instrument panel lower trim panel
     
    Steering column lower shroud
     
    Driver air bag module
     
    Clockspring
     
    Instrument panel temperature sensor hose
     
    Instrument panel console
     
    Instrument panel retaining bracket
     
    Floor console duct retaining clip
     
    Scuff plate trim panel
     
    Cowl side trim panel
     
    Footwell electrical connectors
     
    Climate control electrical connectors
     
    Instrument panel end panel
     
    Sunload sensor
     
    Defogger duct
     
    Instrument panel retaining bolts
     
    Instrument panel
     

  4.  

To install:

  1. To install, reverse the removal procedure.
  2.  
  3. Tighten all instrument panel retaining bolts to 15 ft. lbs. (20 Nm).
  4.  
  5. Tighten air bag module to 62 inch lbs. (7 Nm).
  6.  
  7. Reconnect negative battery cable.
  8.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Instrument panel lower trim panel
     
    Steering column lower shroud
     
    Instrument panel multi-switch pack
     
    Instrument panel support bracket connectors
     
    Instrument panel support bracket
     
    A pillar trim panels
     
    Instrument panel end caps
     
    Door weather stripping
     
    Defroster vent
     
    Passenger side trim panels
     
    Instrument panel connectors
     
    Instrument panel bolts and screws
     
    Instrument panel
     

  4.  

To install:

  1. To install, reverse the removal procedure.
  2.  
  3. Tighten all instrument panel retaining bolts to 15 ft. lbs. (20 Nm).
  4.  
  5. Tighten steering column bolts to 18 ft. lbs. (25 Nm).
  6.  
  7. Tighten air bag module to 62 inch lbs. (7 Nm).
  8.  
  9. Reconnect negative battery cable.
  10.  

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Remove or disconnect the following:

    Negative battery cable
     
    Instrument panel console
     
    Climate control panel
     
    Navigation screen, if equipped
     
    Instrument cluster
     
    Passenger finish panel
     
    Right side end panel trim
     
    Support panel
     
    Lower vent
     
    Instrument panel retaining screws
     
    Instrument panel
     
    Center register air duct
     
    Glove box mounting frame
     
    Remaining electrical connectors
     
    Instrument panel cross beam
     

  4.  

To install:

  1. To install, reverse the removal procedure.
  2.  
  3. Tighten all instrument panel retaining bolts to 15 ft. lbs. (20 Nm).
  4.  
  5. Tighten steering column bolts to 18 ft. lbs. (25 Nm).
  6.  
  7. Tighten air bag module to 80 inch lbs. (9 Nm).
  8.  
  9. Reconnect negative battery cable.
  10.  

  1. Disconnect the battery ground cable.
  2.  
  3. Remove the ashtray retaining screws.
  4.  
  5. Remove the ashtray. Disconnect the electrical connectors.
  6.  
  7. Remove the climate control assembly mounting bracket upper retaining screws cover.
  8.  
  9. Remove the climate control assembly mounting bracket upper retaining screws.
  10.  
  11. Remove the climate control assembly mounting bracket lower retaining screws.
  12.  
  13. Disconnect the hazard lamp switch assembly electrical connectors.
  14.  
  15. Remove the hazard lamp switch assembly. Remove the retaining screws.
  16.  
  17. Disconnect the climate control assembly electrical connectors.
  18.  
  19. Remove the climate control assembly retaining screws.
  20.  
  21. Remove the retaining screws. Remove the climate control assembly.
  22.  
  23. Installation is the reverse of the removal procedure.
    NOTE
    Make sure the climate control assembly is correctly located into the audio unit.

  24.  

 
label.common.footer.alt.autozoneLogo