Jaguar 2000-06

Window Systems

Print

Removal & Installation



Motor & Regulator
Sedan
Rear Door
  1. Remove the rear door window glass.
  2.  
  3. Detach the rear door window regulator and motor.
  4.  
  5. Remove the rear door window regulator and motor. Disconnect the rear door window regulator and motor electrical connector.
  6.  
  7. To install, reverse the removal procedure.

    Click image to see an enlarged view

    Fig. Removing window motor and regulator-Sedan Rear

  8.  

Front Door
  1. Remove the front door window glass.
  2.  
  3. Detach the front door window regulator and motor.
  4.  
  5. Detach the front door window regulator and motor.
  6.  
  7. Remove the front door window regulator and motor. Disconnect the front door window regulator and motor electrical connector.
  8.  
  9. To install, reverse removal procedure.

    Click image to see an enlarged view

    Fig. Removing window motor and regulator-Sedan Front

  10.  

Coupe & Convertible
  1. With door open, turn ignition key to position II.
  2.  
  3. Motor door glass to fully lowered position.
  4.  
  5. Turn ignition key to position O.
  6.  
  7. Disconnect the negative battery cable.
  8.  
  9. Remove door casing for access.
  10.  
  11. Remove speaker.
  12.  
  13. Remove main water shedder and position secondary shedder clear of regulator assembly.
  14.  
  15. Remove clips from nylon fixings and retain for re-use.
  16.  
  17. Release glass regulator assembly from nylon fixings.
  18.  
  19. Manually raise glass to uppermost position and using linen or similarly strong tape, secure glass to top of door.
  20.  
  21. Accessing via speaker aperture, disconnect harness multiplug from lift motor.
    NOTE
    The position of this stud is critical to glass alignment and must be measured accurately.

  22.  
  23. Using vernier calipers, measure position of regulator channel securing stud in elongated hole and slacken and remove nut.
  24.  
  25. Slacken and remove screws securing lift motor to door.
  26.  
  27. Lower motor/regulator assembly into bottom of door and close scissor mechanism.
  28.  
  29. Turning it to achieve clearance, withdraw motor/regulator assembly through door aperture.
  30.  
  31. Place assembly on bench, slacken and remove screws securing lift motor to regulator and remove motor.

    Click image to see an enlarged view

    Fig. Removing motor/regulator assembly-Coupe and Convertible

  32.  

To install:

  1. Position lift motor on regulator assembly and fit and tighten securing screws.
  2.  
  3. Close scissor mechanism and pass assembly through aperture into door.
  4.  
  5. Position motor/regulator assembly in door.
  6.  
  7. Fit but do not tighten motor to door securing screws and regulator channel securing nut.
  8.  
  9. Position regulator channel securing stud in elongated hole as measured during removal and fit and fully tighten securing nut.
  10.  
  11. Fully tighten motor to door securing screws.
  12.  
  13. Supporting door glass, remove linen tape and lower glass onto regulator assembly.
  14.  
  15. Press regulator ball joints into nylon seats on lower channel and fit retaining clips.
  16.  
  17. Connect harness multiplug to motor.
  18.  
  19. Position speaker in door and connect harness multiplug.
  20.  
  21. Align speaker and new gasket in door and fit and tighten securing screws.
  22.  
  23. Fit door casing.
  24.  

Diagnosis & Testing



  1. Inspect the fuses, relays, window motors, loose or corroded electrical connector, switch and circuits. Repair as necessary.
  2.  

 
label.common.footer.alt.autozoneLogo